The steel shaft is made from two segments: AC has a diameter of 50 mm, and CB has a diameter of 100 mm. If the shaft is fixed at its ends A and B and subjected to a torque of 1500 N.m, and G= 76 GPa. 50 mm D 1500N.m 30 mm 80 mm 100 mm B 120 mm 1- What is the torque value at point A in (N.m)? O 141.18 O 988.23 O 264.71 O 1235.29 O 211.76 None 2- What is the maximum shear stress in the shaft in (MPa)? O 8.63 O 5.75 O 3.60 O 10.79 2.87 O None

The steel shaft is made from two segments: AC has a diameter of 50 mm, and CB has a diameter of 100 mm. If the shaft is fixed at its ends A and B and subjected to a torque of 1500 N.m, and G= 76 GPa. 50 mm D 1500N.m 30 mm 80 mm 100 mm B 120 mm 1- What is the torque value at point A in (N.m)? O 141.18 O 988.23 O 264.71 O 1235.29 O 211.76 None 2- What is the maximum shear stress in the shaft in (MPa)? O 8.63 O 5.75 O 3.60 O 10.79 2.87 O None

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The steel shaft is made from two segments: AC has a diameter of 50 mm, and CB has a diameter of 100 mm. If the shaft is fixed at its ends A and B and subjected to a torque of 800 N.m, and G = 76 GPa. st 50 mm s00 N.m 30 mm 100 mm 80 mm 120 mm 1- What is the torque value at polint A in (N.m)? O 88.32 O 411.76 658.82 O. 141.18 O 264.71 None 2- What is the maximum shear stress in the shaft in (MPa)? O 8.63 O 5.75 O3,60 O 10.79 O 2.87 O None
The steel shaft is made from two segments: AC has a diameter of 50 mm, and CB has a diameter of 100 mm. If the shaft is fixed at its ends A and B and subjected to a torque of 1200 N.m, and G = 76 GPa. st A 50 mm D_1200N.m 30 mm 100 mm 80 mm 120 mm 1- What is the torque value at point A in (N.m)?
A shaft is fixed at support C and has a torque of 75lb.ft with respect to free end at a distance of 0.75ft from C. It remains constant for 0.75ft before a negative uniformly distributed torque of 1200lb.ft/ft at a distance of 1.5ft is introduced. The shaft then remains flat for 1.5ft to free end with a torque of 600lb.ft. where in the shaft is the torque equals to negative 1200lb.ft measured from the free end?
Determine the torque that can be transmitted by this shaft. D = 120 mm d = 80 mm L = 3 m Modulus of rigidity, G = 90 GPa = 30 Outer diameter, Inside diameter, IT Length of shaft, 3m Angle of twist
What is the minimum diameter of a solid steel shaft that will not twist through more than 10 degrees in a 6 m length when subjected to a torque of 28 kN.m.?Use G=83 GPa. 131.33 mm 125.22 mm 118 mm 104.25 mm
The shaft shown below consists of three segments AB, BC and CD is subjected to the three torques T1=114 N.m, T2=245 N.m and T3=441 N N.m. The length of each segment is L1=0.71 m, L2=0.31 m and L3=0.43 m . The diameter of each segment is d1=46 mm, d2=97 mm and d3=131 mm . The material have modulus of rigidity G = 143 Gpa. Answer the following questions
A shaft made from acrylic is subjected to the three torques indicated below. The acrylic has a shear modulus of 1.7 GPa. Determine: a. The twist at the end D if the diameter if the shaft is 100 mm. b. The minimum shaft diameter if Tallow = 10 MPa 200 N•m A 800 N•m 300 mm B 400 N•m 600 mm C 600 mm
O A. Given a homogenous shaft with length L, radius R, and modulus of rigidity G, if the internal torque along the shaft is given by the equation T(x) = 0.5x, what is the magnitude of the angle of twist at æ = L? Select one: O B L 4.JG O C. TG O D. E
A solid constant-diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Determine the internal torque in segment (2) of the shaft. Assume that TA = 130 N-m, TB = 300 N-m, Tc= 365 N-m, and Tp = 195 N-m. X TD O -155 N-m -204 N-m O -170 N-m -230 N-m O-214 N-m Tc C (2) B TB (1) TA
What is the minimum diameter of a solid steel shaft that will not twist through more than 4o in a 9 m length when subjected to a torque of 11 kN.m ? if G = 83 GPa
3. The two identical shafts, 1 and 2, are built into supports at their left ends. Gears mounted on their right ends engage a third gear that is attached to shaft 3. Determine the torques in shafts 1 and 2 when the 500N -m torque is applied to shaft 3. 40 500 Nm 80 Dimensions in mm 4. A 4-ft-long tube with the cross section shown in the figure is made of aluminum. Find the torque that will cause a maximum shear stress of 10 000 psi. Use G = 4 x 106 psi for aluminum. +4 in. → 0.04 in. 0.08 in.´ 5. Two steel springs are arranged in series as shown. The upper spring has 36 turns of 100-mm- diameter wire on a mean radius of 350 mm. The lower spring consists of 24 turns of 75-mm diameter wire on a mean radius of 245 mm. If the ultimate shearing stress in either spring must not exceed 692 MPa, (a) compute the maximum value of P and total elongation using factor of safety equal to 1.5. (b) What is the equivalent spring constant? Use G = 83 GPa. 2 of 2 4 in. wwwww.-
A hollow steel shaft is stressed to 35 MPa by a torque of 200000Nm. Determine the outside diameter in mm if the inside diameter is 2/3 of the outside diameter both in mm.