The state of stress shown below is from the surface of a bar under axial and torsion loading. Calculate the principal stresses and directions (i.e., the value of the angle 0). Draw the state of stress aligned with the principal directions. a 60 MPa b. 40 MPa 40 MPa

The state of stress shown below is from the surface of a bar under axial and torsion loading. Calculate the principal stresses and directions (i.e., the value of the angle 0). Draw the state of stress aligned with the principal directions. a 60 MPa b. 40 MPa 40 MPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 410 N 30° 45° 200 N 10 10 mm

Q: stress of +140 MPa, and a minimum stress of -70 MPa. The R-ratio (minimum stress to maximum stress)…

A: Given data; Mean stress =+140 MpaMinimum stress=-70 MpaTherefore we have to find the R ratio for…

Q: The state of stress at a point is given by ox = -6 MPa, ơy = 4 MPa, and Txy = -8 MPa. The maximum…

Q: 1. A bar is subjected to a tensile stress of 100 MPa, Determine the normal and tangential stresses…

A: Givenσ=100Mpaθ=30o

Q: 6. In a plane stress condition, the components of stress at a point are o, =20 MPa, oy =80 MPa and…

Q: 1. A point in a strained material is subjected to a tensile stress of 120 MPa and a clockwise shear…

Q: If force of 6 N Produce stress of 30 N/mm2. What is the cross sectional area on which force is…

Q: The state of stress at a point under plane stress condition is Ox = 150 MPa, Oy = 50 MPa, Txy = 20…

A: Mohr's circle is a two dimensional graphical representation of state of stress at a point. Mohr's…

Q: 2. Discuss briefly what are stress elements and how essential are these on the analysis of principal…

A: To discuss: What is stress element and how essential are these on the analysis of principle stress…

Q: Q2) The lower ends of the three steel rods shown in (FIG. Q2) are at the same level before the force…

Q: Problem 1-5 The Cartesian components of stress at a point are given below : Oy = 5, Tyz = - 4,…

Q: Plain stresses in a plain stress are; 0,=130 MPa 02=60 MPa Magnitude of the maximum shear stress is…

A: Given that σ1=130 MPa σ2=60 MPa We know that maximum shear stress is τmax=σ1-σ22

Q: 3. For the state of stress shown below, calculate the principal stresses and maximum shear stress.

A: σx = 90 Mpa σy = -60 Mpa Txy = 20 Mpa

Q: 14. The inclined member in Fig. 2 is subjected to a compressive force of 600 lb. Determine the…

Q: A body is subjected to a direct tensile stress of 300 MPa in one plane accompanied by a simple shear…

A: given data tensile stress = 300 MPa simple shear = 200 MPa to determine maximum shear stress

Q: QUESTION 4) For the given plane state stress, if the 14 MPa components at the inclined surface is…

Q: PROBLEM: Find the values and plot the distribution of stress over the cross section of the upright…

A: The Answer is below

Q: A horizontal force P= 110,976 N is pushing an inverted L-frame supported by a foundation at the…

Q: Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid…

Q: 10 rivets are fastened on a lap joint of 1.25 inch in diameter the thickness of the lap join were…

A: Given: Number of rivets→n=10 Diameter of the each rivet→d=1.25 inch Hence area for shear…

Q: For the state of plane stress shown in Fig. determine (a) the princi-pal planes, (b) the principal…

A: σx=50MPaσY=-10 MPaτxy=40 MPa (a) the principal planes…

Q: QITHE state of plane stress at a point is represented by the stress element below: A. Draw the…

Q: 1.24 The figure shows a glued joint, known as a finger joint, in a 6-in. by 3/4-in. piece of lumber.…

A: Given Data: The longitudinal force subjected to the timber is, P=800 lb. The width of the lumber…

Q: Find the principal normal stresses and their directions that will occur in case of stress in the…

Q: At a point in a material, the principal stresses are 800 N/cm² and 300 N/cm² where both are tensile.…

Q: 3MP 8MPd 45 2MPA Determine the two principal stresses in MPd

Q: Calculate the stress in the steel from the given figure. Use P1=300KN and P2-45KN. Answer in MPa…

Q: Determine the minor principal stress and position of the principal plane when a block is subjected…

A: given data: stress in x direction(σx)=100MPa(tensile)stress in y direction…

Q: A 4ft long rod with a 0.29 inch diameter is subjected to a 10,130Ib tensile load. What is the…

Q: the circumferential stress of the edge of a simply supported circular plate which is subjected to a…

A: Solution : The objective is to find the circumferential stress of the edge of a simply supported…

Q: In the Figure 5, the normal stress on the cross- sectional area is (in Mpa): Figure 5: y P = 400 KN…

A: Area = A = 20 X 30 = 600 mm2 Force normal to area Pn = 400 cos (30) Pn = 346.41 KN

Q: a) Calculate the principal stresses, given that the state of plane stress for an element is: Oy =…

Q: The solid rod shown in Fig. has a radius of 0.75 in. If it is subjected to the force of 800 lb,…

A: Given Data⇒ Diameter of the solid rod(d)=2R d=2×0.75 d=1.5 m Force applied (F)=800 lb…

Q: The solid rod shown in Fig. has a radius of 0.75 in. If it is subjected to the force of 800 lb,…

A: Given Data The radius of a solid rod, r=0.75 in load, P=800 lb

Q: Calculate the applied shear stress Given a

A: Calculate shear strain

Q: C 800 mm 18 mm dia. Rectangular bar B D 16 mm thick 25 mm 400 mm A F - F -800 mm

A: Given Data The force given is: 24 kN The height of the complee member is: 1200 mm The thickness of…

Q: QUESTION 4) For the given plane state stress, if the components at the inclined surface is known and…

Q: For the following state of stress, 48 MPa 16 MPa 60 MPa Find: i. The principal planes ii. The…

A: Given data: σx=16 MPaσy=-48 MPaτxy=60 MPa Need to determine the principal plane, principal stress,…

Q: A 30 mm square is drawn on the rim of a large steel pressure vessel. The biaxial stress situation in…

A: First calculate the strain in y-direction εy using the equation. εy=σyE-νσxE Here,σx is the normal…

Q: 'igure Q5 shows few loadings applied on bar ABD. Suppose the diameter of the bar is 120 mm, and…

Q: Mohr’s circle is shown for a point in a physical object that is subjected to plane stress. Each grid…

A: Given data as per question Each grid slide=16 MPaFor a point in a physical object that is subjected…

Q: Fill in the blanks. Draw and label the Mohr’s circle. For sigma-yp = 30 kSf. does this fail? Find…

Q: Calculate the compressive stress in a 10.0 mm square rod loaded with 2250 N of force distributed…

A: Given DataF=2250Nb=10mm

Q: The solid rod shown in Fig. has a radius of 0.75 in. If it is subjected to the force of 800 lb,…

A: Given: Diameter of the rod (D)=1.5inForce (F)=800lb

Q: A force 10N is applied to one end of a 10 inches diameter circular rod. Calculate the stress. 3.821…

A: Answer: The stress in the rod is 197.3525 N/m2.

Q: 1. For the two cases i.e. (a) 2D and (b) 3D shown below, find the principal stresses, maximum shear…

A: a) The given values are - σx= 60MPa , τxy=40 MPa , σy= 0 The principal stresses are given by - σ1,…

Q: Given sigma x=100 MPa, tau xy=50 MPa, determine stresses at an angle 30 degrees CW from x-axis.

Q: QUESTION 4) For the given plane state stress, if the components at the inclined surface is known and…

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

The state of stress shown below is from the surface of a bar under axial and torsion
loading. Calculate the principal stresses and directions (i.e, the value of the angle 0).
Draw the state of stress aligned with the principal directions.
60 MPa
T
9.
40 MPa
40 MPа

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q2- Show the stress components of a point in plane stress on the square in Figures below: Ty = 18 ksi Oy = 85 ksi (T) = 27 ksi (C) Oxx 1- 18 ksi %3D = 100 MPa (T) =-75 MPa 2- = -75 MPa = 85 MPa (T)
Problem 2: Use an eigenvalue approach to solve for the principal stresses and directions for the state of stress shown below. Show the principal stresses on a properly oriented element of material. 20 mPa
? (sigma) = 90 40 0 40 −50 0 0 0 0 MPaa. Plot the shear and normal stresses on a given oblique plane (rotated plane) on a graph (stress vs. angle) and show the max. shear plane and the principal planes. (like in the image, using excel) b.If the steel sample has a Young’s modulus of 193 GPa, compute the dimensional changes of the plate under the above loading condition. Shear moduli is 70Gpa.
Illistrate Mohr's circle for the given plane stress state. Including the coordinates of the points, show the points with the faces of the figure, the center of the circle and the magnitude of the radius. 7. 3kPa 5kPa 1kPa
A knuckle joint is used to connect two circular rods. The tensile force applied is 50 kN. The tensile stress in the rod and the shear stress in the pin are 25.46 MPa and 35.37 MPa, respectively. Determine the required diameter of the rod and the pin in mm.
Q1. For the given cube below, complete the following: 1.find the center, radius (R), principal normal stresses (σ and σ3), max shear stress (Tmax) and draw the Mohr's Circle. 2. Find the stresses on a plane that is rotated 60° clockwise from the horizontal plane. 6PSE IPSF 10pst 60⁰ TOPST IPSF 6PSF
Q1 / If the cross section of the femur can be approximated as a circular tube, determine the state of stresses on the points A and B at section due to the loads as shown in figure Q1. T. = 2 cm = 1.6 cm %3D Figure Q1 B L 20 cm
Problem 1: Given the 2D states of plane stress below, determine the principal stresses (0₁, 0₂) and the maximum shear stress (Tmax). Show your work. ox ºy Txy 90 MPa -30 MPa 15 MPa 90 MPa 180 MPa 60 MPa 0 MPa -40 MPa 120 MPa 01 02 03 Tmax
the state of stress at a point can be described by óx=36 MPa and Txy= 17MPa a second coordinate system is rotated by theta35 degrees What is the normal stress in the direction of the x' axis what is the shear stress in the y'-direction for the faces with a normal in the x'-direction what is the normal stress in the direction of the y'-axis
A rectangular block of size in mm as shown in fig., is subjected to stressess. Determine the change in linear dimension and change in volume of the block. Take E = 200 X 106 kPa and poisson's ratio = 0.3. 140MPA 50MPA 140MPA 50 MPa 900 600
1. Calculate the maximum stresses to occur in the hole and groove (groove) areas in the plate below, whose geometry and the applied force are known. 200 mm d = 30 mm 5000 N 5000 N t= 25 mm r= 15 mm
3. For the state of stress shown below, calculate the principal stresses and maximum shear stress. 60 MPa Txy = 20 MPa 90 mla