The state of plane stress at a point with respect to the xy-axes is shown in Fig. (a). Using Mohr's circle, determine (1) the principal stresses and principal planes; (2) the maximum in-plane shear stress; and (3) the equivalent state of stress with respect to the x'y'-axes. Show all results on sketches of properly oriented elements. y20 MPa 50° 40 MPa 16 MPa (a)

The state of plane stress at a point with respect to the xy-axes is shown in Fig. (a). Using Mohr's circle, determine (1) the principal stresses and principal planes; (2) the maximum in-plane shear stress; and (3) the equivalent state of stress with respect to the x'y'-axes. Show all results on sketches of properly oriented elements. y20 MPa 50° 40 MPa 16 MPa (a)

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.21P: An clement m plane stress from the frame of a racing car is oriented at a known angle 8 (sec...

See similar textbooks

Similar questions

-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
An clement m plane stress from the frame of a racing car is oriented at a known angle 8 (sec figure). On this inclined clement, the normal and shear stresses have the magnitudes and directions shown in the figure. Determine the normal and shear stresses acting on an clement whose sides are parallel to the \y axes, that is, determine crv, tr(_, and t, Show the results on a sketch of an clement oriented at B .
(a) Construct Mohr's circle for an element in a uniaxial state of stress (b) Use this Mohr's circle to derive the equation for the normal stress On and shear stress En on the n-face. The equations should depend on Ox and θ (c) Use the Mohr's circle to determine the planes on which the maximum shear stress acts. Sketch a properly oriented maximum-shear-stress element and indicate the normal and shear stresses acting on its faces. Ơn nt o, Note: for (b), the angle θ is between 0 and 90° and is positive
3. (a) Using Stress transformation equations, determine the principal planes, the principal stresses, the maximum in-plane shear stress and the corresponding normal stress. (b) Solve part (a) using Mohr's circle. 100 MPa 75 MPa 150 MPa
2. At a point in a brocket, the stresses on two mutually perpendicular planes are 180 MN/m? (tensile) and 70 MN/m2 (Compressive). The shear stress across the planes is 65 MN/m2. Find the following by Mohr's Circle method and compare with Analytical solutions: (i)The Normal stress on a plane making an angle of 50° with the plane of first stress. (ii)Shear stress on the plane (iii) Maximum shear stress (iv) Resultant stress and it's direction. (v) Major and minor principal stresses.
The state of stress at a point in a soil beneath a level ground surface consists of a major principal stress of 70 kPa and a minor principal stress of 25 kPa. The major principal stress acts in the vertical direction. (a) Draw the Mohr's circle of stress and show the pole point (origin of planes). (b) Determine the maximum shear stress and calculate the orientation angle (relative to horizontal) of the plane of positive maximum shear stress. (c) Determine the normal stress and shear stress on a plane that makes an angle of -20° (i.e., 20° clockwise) relative to the horizontal plane.
To determine the normal and shear stresses on the indicated plane, we must first determine the orientation of the inclined plane relative to the x face of the stress element. Determine the magnitude of the counterclockwise angle between the x face and the inclined plane. Assume Sx = 170 MPa, Sy = 105 MPa, Sxy = 85 MPa, and ß = 65°. Sx Sxy В Sy Answer: 0 = 25 X O'
Problem 3: For the plane stress state listed below, draw a Mohr's circle diagram properly labeled. Keep in mind that the principal stress is that stress state where the shear stress is zero. That means it is the stress state along the normal stress line in Mohr's space. So, use your Mohr's circle to find the principal normal and shear stresses, and determine the angle from the x axis to o1. 0x = 16 kpsi, oy = 9 kpsi, Ty = 5 kpsi ccw
1. For the two cases i.e. (a) 2D and (b) 3D shown below, find the principal stresses, maximum shear stresses and directions by using Mohr’s circle. Support your answers with diagrams. 41 GOMPa 60MPR Txy=40MPA 40MPA (a) (b)
Assume the plane stress element shown in Fig. E3-a represents the stress a geosynthetic membrane used in a mechanically stabilized earth wall. If the reference state of stress for this element results in the Mohr’s circle plot shown in Fig. E3-b, determine: The principal stresses. The principal directions (angles to the principal planes). The maximum in-plane shear stress. It is known that the seam, which is rotated 45 deg from the vertical as shown in Fig. E3-c, will fail if subjected to a tensile stress of 25 kPa or a shear stress of 1 kPa. Determine the normal stress and shear stress acting on the seam, and state if the seam will fail due to the loading indicated.
Problem 2: A state of plane stress at a point on the surface of a structure consists of the following stress components: Ox = 18 ksi, oy = 24 ksi, and Txy = 15 ksi. Note that the stress components act in the directions shown on the element below. Ox Txy 24 ksi бу 18 ksi 15 ksi (a) Draw a complete Mohr's circle for this stress state. Clearly label the X and Y faces, the center C, and the radius R. (b) Using Mohr's circle, determine the stress components Ox, Oy, and Txy on an element rotated 25° counter-clockwise from the original element shown. Label all of these quantities on the circle. (c) Show all stresses from part (b) on a properly oriented stress element. Be sure to include all stress components acting on the element.
Mohr's Circle The major and minor principal stresses acting at a point are 80 psi compression and 20 psi tension. (a) Draw the Mohr's circle for this stress combination. (b) What is the maximum shear stress acting at the point, and what value of normal stress acts on the plane? (c) Determine the value of the shear and normal stress acting on a plane that is 30° from the major principal plane. kindly answer the following with a complete solution so that i can understand how to solve it. thank you