The shear modulus of the solid steel shaft is G = 11 x 10° ksi. Motor A is directly coupled to the shaft and delivers 3 hp while rotating at 1800 rpm (revolutions per minute). Gears B, C, and D remove the powers indicated in the figure. Given the following two criteria, determine the required diameter of the shaft to the nearest 1/s in. (1) The maximum shear stress must not exceed Tallow = 9 ksi. (2) In order to prevent binding or interference in the attached machin- ery, the angle of twist of gear B with respect to gear D must not exceed 1°. 1.25 ft 1.0 ft B. 3 hp 1.5 ft 1 hp 0.5 hp 1.5 hp

The shear modulus of the solid steel shaft is G = 11 x 10° ksi. Motor A is directly coupled to the shaft and delivers 3 hp while rotating at 1800 rpm (revolutions per minute). Gears B, C, and D remove the powers indicated in the figure. Given the following two criteria, determine the required diameter of the shaft to the nearest 1/s in. (1) The maximum shear stress must not exceed Tallow = 9 ksi. (2) In order to prevent binding or interference in the attached machin- ery, the angle of twist of gear B with respect to gear D must not exceed 1°. 1.25 ft 1.0 ft B. 3 hp 1.5 ft 1 hp 0.5 hp 1.5 hp

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The solid steel shaft is supported by frictionless bearings in D and E. This system is connected to a motor that provides 5 kW of power to the shaft while rotating at w = 75 rpm. If A and B gears get 2 kW and 3 kW respectively, determine the minimum shaft diameter. w rotation speed and safety shear stress τem = 35MPa are known and given in the table with your names below.
The four gears shown are attached to a steel shaft that is rotating at 2 Hz. Gear B supplies 70 kW of power to the shaft. Of that power, 20kW are used by gear A, 20 kW by gear C and 30kW by gear D. G=83 GPa for steel -20KW JOKN -20kw -30kW 2m 1.5m 1.5m B (a) If a uniform shaft diameter of 125 mm B speci fied, detenmine the angle of rotation of A relative to D. O f segment Co is to be replaced lay a hollaw Shaft with an inside diameter of 80 mm, what is the outside diameter if the stress is not to excced 70 MPa.
The solid steel shaft is supported by the frictionless customer on D and E. This system The mile provided 5 kW of power in w dev / second and was connected to a motor at C. wwww ww www ww ww www wwwm www w A and B If gears get primary 2 kW and 3 kW, determine the minimum shaft diameter. w rotation speed and The safety shear stress is known and is included in the table below. pictures. wwww ww wwwwwwwww www wwwwww wwwwwwww wwwwwwwww w(cycle/second) = 100 tem(Mpa) = 40 3 kW 5 kW 2 kW A D B E C _
The motor delivers a torque of T-60 Nm to the shaft AB. This torque is transmitted to shaft CD using the gears at E and F. The bearings BC, and D allow free rotation of the shafts Figure 50 mm, 30 mm B 35 mm 125 mm 1 of 12 ▾ Determine the maximum shear stress in AB shaft Express your answer with the appropriate units. (TA) 1.415. Submit Part C X Incorrect: Try Again: 5 attempts remaining MPa Previous Answers Request Answer Determine the maximum shear stress in CD shalt Express your answer with the appropriate units. (CD) 2.227 Submit MPa Previous Answers Request Answer ? ?
The electric motor exerts a 500-N-m torque on the aluminum shaft ABCD when it is rotating at a constant speed. The torques exerted on pulleys Band Care as shown. Take a = 1.4 m, b= 0.9 m, and G= 27 GPa. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 300 N. m 200 N. m 45 mm 44 mm 40 mm Im Determine the angle of twist between Band C. The angle of twist between Band Cis|
Determine the diameter of a solid steel shaft which will transmit 112.5 kW at 200 rpm. Also determine the length of the shaft if the twist must not exceed 1.5o over the entire length. The maximum shear stress is limited to 55 N/mm2. Take the value of modulus of rigidity = 8 x 104 N/mm2.
A solid 1.5 in. diameter shaft is used to synchronize multiple mechanisms in a manufacturing plant. The torque delivered by the shaft is 3500 lb-in. What horsepower must be delivered to the shaft to maintain a shaft speed of 670 rpm? What is the maximum shear stress developed in the shaft? Convert the given shaft speed to units of rad/s. Answer: W = i rad/s
The steel shaft with two different diameters rotates at 4.9 Hz. The power supplied to gear C is 54.1 kW, of which 26.9 kW is removed by gear B. Find the angle of rotation of gear A relative to gear Cif d = 55.5 mm, h = 68.9 mm, L = 4.2 m, M = 2.8 m, and G = 83.46 Gpa. Round off the final answer to two decimal places.
The coupled shafts shown are transmitting 270 hp at 600 rev/min. The shafts are connected by a coupling with eight bolts. The bolt circle diameters are 5 and 10 in. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. O 0 600 rev/min Determine the minimum nominal shoulder diameter of a bolt if all bolts are to have the same diameter and not exceed a shear stress of 20 kpsi Select a preferred fraction size. The minimum nominal shoulder diameter of a bolt is, in.
The turbine develops 150 kW of power, which is transmitted to the gears such that C receives 70% and D receives 30%. The rotation of the 100-mm-diameter A-36 steel shaft is a 750 rev/min. The journal bearing at E allows the shaft to turn freely about its axis. The shear modulus of elasticity for A-36 steel is 75 GPa. (Figure 1) Figure 1 of 1 Part A Determine the absolute maximum shear stress in the shaft. Express your answer to three significant figures and include the appropriate units. Tax Value Submit Part B $8/0 Submit Request Answer Determine the angle of twist of end E of the shaft relative to B Express your answer using three significant figures. Provide Feedback VAX Units Request Answer ? Ivec 4 ? rad
STRENGTH OF MATERIALS. Please show the complete solutions. Rate will be given. Answer in 3 decimal places! The steel shaft DF consists of three concentric tubes and is supported by smooth bearings at D and E. It is coupled to a motor at F, which delivers 14 kW of power to the shaft while it is running at 52 rev/sec. The gears A, B, and C remove 3 kW, 5 kW, and 6 kW, respectively. The shaft is free to turn in its support bearings D and F. Determine the shearing stress developed in segments BC and CE.
A motor drives a shaft at 300 rpm and a power output of 100 kW. The shaft is made of A-36 steel and has diameter 128 mm. There are two gears at B and C and power is transmitted to them equally. The bearing at D can be taken to be frictionless. Calculate the maximum shear stress in the shaft, and the angle of twist of D relative to A. The lengths are 2 m, L2 = 3 m, and L3 = 3.5 m. L₁ = A B 030/ 2021 Cathy Zupke X ↳₂ The maximum shear stress is Tmax= 60.9 X MPa The angle of twist (in degrees) between A and D is A/D 58.2 O C