The rigid, horizontal slab is attached to two identical copper rods. There is a gap = 0.18 mm between the middle bar, which is made of aluminum, and the slab. Neglecting the mass of the slab, calculate the stress in each rod when the temperature in the assembly is increased by 85 degrees Celsius. A(mm²) α/°C E (GPa) Copper Rod 500 16.8 x 10-6 120 Aluminum 400 23.1 x 10-6 70 Copper Aluminum Copper 750 mm

The rigid, horizontal slab is attached to two identical copper rods. There is a gap = 0.18 mm between the middle bar, which is made of aluminum, and the slab. Neglecting the mass of the slab, calculate the stress in each rod when the temperature in the assembly is increased by 85 degrees Celsius. A(mm²) α/°C E (GPa) Copper Rod 500 16.8 x 10-6 120 Aluminum 400 23.1 x 10-6 70 Copper Aluminum Copper 750 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

ll ? The rod BD is made of material with G1= 135 GPa has a diameter 16 mm is bonded to the tube CA at point B, the tube made of material with G2=230o GPa has an outer diameter 37 mm and wall thickness of 7 mm. li T1=803 N.m and T2=1445 N.m, answer the following questions: B T2 Nm 04 m 0.1 m 0.3 m TI N-m The polar moment of inertia of the rod BD is Your answer The polar moment of inertia of the tube CA is
An 1500 mm long, 43 mm aluminum square bar is rigidly supported on both ends (stress-free). Determine the stress in the bar if the temperature is raised by 153 °C. For aluminum: the coefficient of thermal expansion is 23 x 10-6/°C, G = 70 Gpa. Answer in Mpa.
A steel rod of 20 mm diameter passes centrally through a copper tube 40 mm external diameter and 30 mm internal diameter. The tube is closed at each end by rigid plates of negligible thickness. The nuts are tightened lightly home on the projected parts of the rod. If the temperature of the assembly is raised by 60°C, calculate the stresses developed in copper and steel. Take E for steel and copper as 200 GN/m2 and 100 GN/m2 and α for steel and copper as 12 x 10-6 per °C and 18 x 10-6 per °C.
Problem #1: The bar below is composed of three solids cylindrical pieces with the diameters shown. The bar initially has a temperature of 70° F, and is slowly heated to a final temperature of 116° F. If the bar initially has zero stress, find the axial stress in each section when the bar reaches its final temperature. Young's Modulus (ksi) Coeff. Thermal Exp. (/°F) | 12.9×10-6 A Aluminum Bronze 10,600 15,000 11.1×106 9.6×10-6 2014-T6 Aluminum 12 in. 4 ft Stainless Steel 28,000 B C 86100 Bronze 8 in. 6 ft 304 Stainless steel C 4 in. 3 ft D
The steel bar AB has a x-in.square cross section and is held by pins that are a fixed distance apart and are located at a distance e = 0.034 in. from the geometric axis of the bar. Determine the required distance d for which the bar will just make contact with point C when the temperature increases by 120°F. Use E= 29 × 106 psi and a coefficient of thermal expansion a = 6.5 × 10-6/°F. Use a simple approximation by ignoring the eccentricity during the thermal part of your calculation. (Round the final answer to four decimal places.) in.- B The distance dis 4 in. 4 in. in.
PROBLEM NO. 2 The rigid bar AB is pinned at 0 and connected to two rods as shown in the figure. If the bar AB is horizongal at a given temperature, determine the ration of the areas of the two rods so that the bar AB will be horizontal at any temperature. Neglect the weight of the bar AB. ALUMINUM E O GPa = 23. Lm/(m°c) 5TRIEL E= 200 6 L= m m'c
A 12mm thick steel tire has a width of 110mm and has an internal diameter of 800mm. The tire is heated and shrunk to a steel wheel 800.5 mm in diameter. The modulus of elasticity E = 200 MPa. a. Determine the tensile stress in the tire. b. Determine the compressive pressure between the tire and the wheel. c. Determine the thickness of the tire to resist a pressure of 1.5 MPa if it has an allowable stress of 124 MPa. I need answer ASAP. Thank you!
The 50-mm-diameter cylinder is made from Am 1004-T61 magnesium and is placed in the clamp when the temperature is T₁ = 15°C. (Figure 1) Figure Part A 100 mm T₂ = Value If the two 304-stainless-steel carriage bolts of the clamp each have a diameter of 10 mm, and they hold the cylinder snug with negligible force against the rigid jaws, determine the temperature at which the average normal stress in either the magnesium or the steel first becomes 11.5 MPa. Express your answer to three significant figures and include the appropriate units. Units Submit Previous Answers Request Answer 150 mm ? 1 of 1
The 50-mm-diameter cylinder is made from Am 1004-T61 magnesium and is placed in the clamp when the temperature is T₁ = 15°C. (Figure 1) Figure 100 mm 150 mm 1 of 1 > Part A If the two 304-stainless-steel carriage bolts of the clamp each have a diameter of 10 mm, and they hold the cylinder snug with negligible force against the rigid jaws, determine the temperature at which the average normal stress in either the magnesium or the steel first becomes 14.5 MPa Express your answer to three significant figures and include the appropriate units. ºμÀ T₂ = 150.54 Submit 6 Provide Feedback ➜ C Previous Answers Request Answer ? X Incorrect; Try Again; 5 attempts remaining Next >
The horizontal steel rod, 2.5 m long and 1200 mm2 in crosssectional area, is secured between two walls as. If the rod is stress-free at 20_C, compute the stress when the temperature has dropped to _20_C. Assume that (1) the walls do not move and (2) the walls move together a distance Δ = 0.5 mm. Use α = 11.7x10-6 oC and E = 200 GPa.
The 50-mm-diameter cylinder is made from Am 1004-T61 magnesium and is placed in the clamp when the temperature is T₁ = 15°C. (Figure 1) Figure 100 mm 1 of 1 150 mm Part A If the two 304-stainless-steel carriage bolts of the clamp each have a diameter of 10 mm, and they hold the cylinder snug with negligible force against the rigid jaws, determine the temperature at which the average normal stress in either the magnesium or the steel first becomes 10.0 MPa Express your answer to three significant figures and include the appropriate units. T₂ = 244 μA Submit Previous Answers Request Answer Provide Feedback ? X Incorrect; Try Again; 8 attempts remaining Next >
The 50-mm-diameter cylinder is made from Am 1004- T61 magnesium and is placed in the clamp when the temperature is T₁ = 15°C. (Figure 1) Figure 100 mm 1 of 1 150 mm Part A If the two 304-stainless-steel carriage bolts of the clamp each have a diameter of 10 mm, and they hold the cylinder snug with negligible force against the rigid jaws, determine the temperature at which the average normal stress in either the magnesium or the steel first becomes 15.0 MPa. Express your answer to three significant figures and include the appropriate units. T₂ = Submit 1 μА Value Provide Feedback ← Request Answer A Units ? Next >