The Rexroth simulators have the following component specifications: Double acting cylinders with piston diameters of 25-mm and rod diameters of 16-mm. Cylinder stroke of 40-cm for the large cylinder and 20-cm for the small cylinder(s). Pump rated output of 8 liters/minute. Maximum cylinder pressure of 105 bar (10500 kPa). Calculate the following based on the above system specifications. Refer to the formula sheet attached to this lab: a. Piston area [Ap] and rod area [AR] in units of m2. Ap = AR x De 4 = x0.025 x 0-016? 0.00020 m? b. Maximum cylinder force in extension [FE], retraction [FR] and regeneration [Fregen]: = 0.00049 m?

The Rexroth simulators have the following component specifications: Double acting cylinders with piston diameters of 25-mm and rod diameters of 16-mm. Cylinder stroke of 40-cm for the large cylinder and 20-cm for the small cylinder(s). Pump rated output of 8 liters/minute. Maximum cylinder pressure of 105 bar (10500 kPa). Calculate the following based on the above system specifications. Refer to the formula sheet attached to this lab: a. Piston area [Ap] and rod area [AR] in units of m2. Ap = AR x De 4 = x0.025 x 0-016? 0.00020 m? b. Maximum cylinder force in extension [FE], retraction [FR] and regeneration [Fregen]: = 0.00049 m?

Name: can you please find solution for part b? The Rexroth simulators have t
Uploaded: 2024-03-20T06:51:10.000Z
Channel: Bartleby
Description: can you please find solution for part b? The Rexroth simulators have the following component specifications:Double acting cylinders with piston diameters of 25-mm and rod diameters of 16-mm.Cylinder stroke of 40-cm for the large cylinder and 20-cm fo

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter14: Fluid Mechanics

Section: Chapter Questions

Problem 125CP: The inside volume of a house is equivalent to that of a rectangular solid 13.0 m wide by 200 m long...

See similar textbooks

Similar questions

Technician A says that oil should be squirted into all of the cylinders before taking a compression test. Technician B says that if the compression greatly increases when some oil is squirted into the cylinders, it indicates defective or worn piston rings.
In the figure below, what is the pressure of the gas in the flask (in atm) if the barometer reads 693.4 torr? (Ah = 8.37 cm) oo Round your answer to 4 significant figures. Open end Gas Ah Note: Reference the SI prefixes and Conversion factors for non-SI units tables for additional information. Pressure = 0.9123 atm 0 x10 X olo Ar B
What is the pressure of the gas in the cylinder, in kPa (kiloPascal)? h = 0.620 m, Pmercury = 13,600 kg/m3, 1.0 atm = 1.00 x 105 Pa = 100 kPa, and g = 10.0 m/s?. Your answer needs to have 3 significant figures, including the negative sign in your answer if needed. Do not include the positive sign if the answer is positive. No unit is needed in your answer, it is already given in the question statement. Mercury. p = 13,600 kg/m² Pen
An Aircraft engine cylinder has a piston displacement of 45 cubic inches and a clearance volume of 10 cubic inches. If the intake pressure is 14.7 PSIA what is the absolute pressure when the piston is at TDC? What is the compression ratio?
The pressure of a gas contained in a cylinder with a movable piston is 750 Pa. The area of the piston is 1.5 m2. Calculate the force that is exerted on the piston.
A cylinder is filled with10.0Lof gas and a piston is put into it. The initial pressure of the gas is measured to be 268.kPa.The piston is now pushed down, compressing the gas, until the gas has a final volume of 8.70L. Calculate the final pressure of the gas. Round your answer to 3 significant digits.
A balloon contains 6 L of He. The pressure is reduced to 1 atm and the balloon expands to occupy a volume of 12.25 L, T constant. What was the initial pressure exerted on the balloon? (Give your answer correct to two decimal places) The pressure is atm
A booster pump on a brake system designed to be used horizontally consists of two cylinders capped by pistons connected by a hose. The cylinders and hose are filled with an incompressible fluid. The system produces a mechanical advantage of six times; that is, the output force is six times as great as the input force. If the cross-sectional area of the input piston is 2.6 in2, how large (in in2) must the area of the output piston be? _____________in2
2) The pump of a water distribution system is powered by an electric motor whose efficiency is 80% with a shaft that is 97% efficient and a pump that is 60% efficient. The water flow rate through the pump is 0.2 m³/s. What is the total efficiency of the pump/motor assembly? The diameters of the inlet and outlet pipes are the same, and the elevation difference across the pump is negligible. If the pressures at the inlet and outlet of the pump are measured to be 70 kPa and 720 kPa (absolute), respectively, determine the electrical consumption of the pump.
What is the pressure of the gas in the cylinder, in kPa (kiloPascal)? Pmercury = 13,600 kg/m3, 1.0 atm = 1.00 x 105 Pa = 100 kPa, and g = 10.0 m/s?. Your answer needs to have 3 significant figures, including the negative sign in your answer if needed. Do not include the positive sign if the answer is positive. No unit is needed in your answer, it is already given in the question statement. Pgas -Mercury 16 cm 6 cm
A piston has an external pressure of 8.00 barbar. How much work has been done in joules if the cylinder goes from a volume of 0.180 litres to 0.650 litres. Express your answer with the appropriate units. W=
What is the pressure of the gas in the cylinder, in kPa (kiloPascal)? h = 0.700 m, ρmercury = 13,600 kg/m3, 1.0 atm = 1.00 × 105 Pa = 100 kPa, and g = 10.0 m/s2. Your answer needs to have 3 significant figures, including the negative sign in your answer if needed. Do not include the positive sign if the answer is positive. No unit is needed in your answer, it is already given in the question statement.