The request for this project is to design the diameter of the output shaft of a single reduction gearbox with a 20° pressure angle involute spur gear set. The gearbox consists of two (2) shafts, four (4) bearings, two (2) spur gears, and gearbox steel casing, as shown in Figure 1 below. The gearbox is powered by a 3 kW Power, 50 Hz AC electric motor with a speed of 1440 rpm. The main goal of the gearbox is to reduce the speed to 575 rpm. The gearbox had to abide by the following: 1. The weight of the motor and gears do not add to the bending or shear stresses of the system and will be ignored when doing calculations. 2. The entire system is bolted to a horizontal bedplate and will only be accessible from the top surface. 3. The machine components, including bolts, shafts, and bearings, must all be designed with a factor of safety (ns) as 2.5.

The request for this project is to design the diameter of the output shaft of a single reduction gearbox with a 20° pressure angle involute spur gear set. The gearbox consists of two (2) shafts, four (4) bearings, two (2) spur gears, and gearbox steel casing, as shown in Figure 1 below. The gearbox is powered by a 3 kW Power, 50 Hz AC electric motor with a speed of 1440 rpm. The main goal of the gearbox is to reduce the speed to 575 rpm. The gearbox had to abide by the following: 1. The weight of the motor and gears do not add to the bending or shear stresses of the system and will be ignored when doing calculations. 2. The entire system is bolted to a horizontal bedplate and will only be accessible from the top surface. 3. The machine components, including bolts, shafts, and bearings, must all be designed with a factor of safety (ns) as 2.5.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A gearbox is needed to provide an exact increase in speed, while minimizing the overall gearbox size. The input and output shafts should be in-line. Specify appropriate teeth numbers. The gearbox is required to transmit 18 kW from a shaft rotating at 2650 rpm. The desired output speed is exactly 13250 rpm. For space limitation and standardization reasons a double step-up gearbox is requested. Using the limited selection of gears presented in Tables 6.7 to 6.10, select suitable gears for the gears and pinions 24 2650 rpm Table 6.7 Spur gears: 1.0 module, heavy duty steel 817M40, 655M13, face width 15 mm Outer Boss Bore Part PCD diameter diameter diameter number Teeth (mm) (mm) (mm) (mm) SG1.9 9 SG1-10 10 SG1-11 11 SG1-12 12 10:00 12:00 12 11.00 13.00 13 12.00 14.00 14 12.00 14.00 14 SG1-13 13 1300 15.00 15 6 SG1-14 14 1400 16.00 16 6 15.00 17.00 SG1-15 15 6 SG1-16 16 16.00 18.00 SG1-17 17 17.00 19.00 18 SG1-18 18 18.00 20.00 18 SG1-19 19 19:00 21.00 SG1-20 20 2000 2200 21.00 2300 2200…
O It is required to design a pair of spur gears with 20° full-depth involute teeth. The input shaft rotates at 720 rpm and receives 5 kW power through a flexible coupling. The speed of the output shaft should be 144 rpm. The pinion as well as the gear are made of steel Fe 410 (S = 410 N/mm). The service factor.for the application is 1.25. The gears are machined to meet the specifications of Grade 6. ut [LO 6, 7] (i) Assume suitable number of teeth for the pinion and the gear. (ii) For preliminary calculations, assume the pitch line velocity as 5 m/s and the factor of safety as 2. Estimate the module and select the first preference value of the module. (iii) Using this value of the module, calculate the pitch circle diameters of the pinion and gear and the face width. (iv) Determine static load and the dynamic load by Buckingham's equation. Also calculate the beam strength and the correct value of factor of safety based on beam strength. (v) Using a factor of safety of 2 for wear…
A gearbox is needed to provide an exact increase in speed, while minimizing the overall gearbox size. The input and output shafts should be in-line. Specify appropriate teeth numbers. The gearbox is required to transmit 18 kW from a shaft rotating at 2650 rpm. The desired output speed is exactly 13250 rpm. For space limitation and standardization reasons a double step-up gearbox is requested. Using the limited selection of gears presented in Tables 6.7 to 6.10, select suitable gears for the gears and pinions 2650 rpm 13250 rpm
A 70.74 hp motor turning at 2116 rpm is to deliver its power to a worm-gear reducer, whose velocity ratio is to be 25. The worm is shell type and has 3 threads; the worm and gear materials are 8 - High-test CI & High-test CI respectively. Provide the details for this pair of gears if the chosen circular pitch is 5/8. Assume Sn= 31,000 psi. For the diameter of the worm, use the proportion as provided by the equation for hell worms on page 437 of the book of FAIRES. Please answer those on the Table.
Problem 19-11 A pair of straight bevel gears, mounted on shafts which are intersecting at right angles, consists of a 24 teeth pinion meshing with a 32 teeth gear. The module at the large end of the tooth is 5 mm. Calculate : 1. the pitch circle diameters of the pinion and the gear; 2. the pitch angles for the pinion and gear; 3. the cone distance; 4. the formative number of teeth for the pinion and gear; and 5. the back cone radius for the pinion and gear?
A group of first year students are designing gear reduction system in the Makerspace, consisting of four gears A, B, C and D. The radii of the gears are TA = 1.5 in, r = 3.5 in, rc = 2.0 in and r₁= 5.0 in. Gear A rotates clockwise with a constant angular velocity WA = 440 rpm. Gears B and C are rotating together on the same shaft. Determine: @A A B rc C D TA TB "D (a) the angular velocities of gears B and D, (b) the accelerations of the contact point on gear B and contact point on gear D.
Figure Q1 below shows a gear reducer unit which drive a cement mixer drum at output of this unit and attached to a motor at the input. A 1.5 kW motor with a speed of 9 33 rpm is used as an input source to drive this gear reducer. The gear reducer consists two pairs of spur gears which each pair of them have modules of 1.5 mm for gear set 1 and 2.5 mm for gear set 2. All the spur gears have 20 deg pressure angle. Gear set 2 Gear set 1 Вearing 1,5 kW 933rpm Motor Cement mixer drum Gear Reducer Unit Figure Q1: A gear reducer unit a) Calculate torque generated from the motor. (Nm) - [1 mark]
Examine the gear drive shown. The small driving gear has 15 teeth, DP = 8, RPM = 1200, Torque = 4 ft-lbs. The large gear has 54 teeth and DP = 8. What is the Gear Ratio for this system? What is the Speed Ratio for this system? What is the Center to Center spacing of the gears? What is the RPM of the larger gear? What is the Torque supplied by the larger gear?
(a) An epicyclic gear has a fixed sun gear (B) with 200 teeth. The planet gear (C) has 40 teeth Compounde with gear (D) (140 teeth). The input shaft delivers 400 W at 3600 rev/min. the gear box efficiency is 70%. Calculate the following: I. The number of teeth on (E). II. The gear box ratio III. The output speed and its direction IV. The holding torque. D Input Output D
Design A two stage spur gear reduction unit with 20- Deg full depth involute teeth. The input shaft rotates at 1440 rpm and receives 10 kW power. The speed of the output shaft should be approximately 180 rpm plus minus 5 rpm , All gears are made of steel and have the same module . Determine appropriate number of teeth of the gears in the unit .
Explain the following terms with reference to Spur gears: ①Pitch circle ② pressure angle ⑤ Backlash 6 Base Circle 3 circular pitch (4) Addendum
Asap