The registers A. B. C. D. A. The cache memory. B. C. D. A. B. hold specific data for the fetch-decode-execute cycle store data inside the CPU C. do any maths or logic problems for the CPU send out control signals for the CPU D. stores frequently used instructions close to the CPU What does the CU do? sends out control signals for the CPU holds specific data for the fetch-decode-execute cycle does any maths or logic problems for the CPU Stores frequently used data and instructions Decodes and directs instructions to be carried out Performs Arithmetic and Logical operations Processes graphical functions

The registers A. B. C. D. A. The cache memory. B. C. D. A. B. hold specific data for the fetch-decode-execute cycle store data inside the CPU C. do any maths or logic problems for the CPU send out control signals for the CPU D. stores frequently used instructions close to the CPU What does the CU do? sends out control signals for the CPU holds specific data for the fetch-decode-execute cycle does any maths or logic problems for the CPU Stores frequently used data and instructions Decodes and directs instructions to be carried out Performs Arithmetic and Logical operations Processes graphical functions

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

4) Design and draw these memory units with their control circuits. Explain operations. a) A single EPROM 2716 is used with an 8088 microprocessor so that this microprocessor will see only X bytes of memory between the address range of DF800 –DFFFF or DD800 - DDFFF instead of 1M byte that it expects. Draw this circuit. What are X bytes? Do not use 74138 decoders. b) Design and show a 16K x 16-bit memory circuit by using 8K x 8-bit RAMS. Explain its operation. Do not use decoder 74138 chip.
- The stack memory is addressed by a combination of the plus offset. The PUSH and POP instructions always transfer between segment -bit number the stack and a register or memory location in the 8086 microprocessors. For string instructions, DI always addresses data in the segment. The 8086 LOOP instruction decrements register for a 0 to decide if a jump occurs and tests it
An 8051 subroutine is shown below: SUB: RO, #20H @RO , #0 MOV LOOP: MOV INC RO CJNE RO, #80H, LOOP RET a. What does this subroutine do? b. In how many machine cycles does each instruction execute? How many bytes long is each instruction? C. d. Convert the subroutine to machine language. e. How long does this' subroutine take to execute? (Assume 12 M
3- what is the advantages of memory segment. 4- state the purposes of segment registér. 5- what is the different between general purpose register and segment register and flag register.
Explain the SUB instruction of 8086. Compare it with SBB instruction. Write a Assembly language program for 8086 to find the square root of a number using SUB instruction. (Note : Solve the question in paper, scan and upload along with the other Part B and C answers) A BIE
If R0 = 0x20008000, after run STMDB r0!, {r3, r9, r7, r1, r2} command what is the r7 register memory start address?A. R0= 0x20007ff4B. R0 = 0x20007ffefC. R0 = 0x20007fffD. R0=0x20007fecE. R0 = 0x20007ff0
Given a 8-bit number at memory location 2050H. Write 8085 instruction to move the value stored at the following locations: Register B Accumulator 2052H Write a single program and show register and accumulator screenshot and also attach memory view. In sim8085 software.
A) List and describe 10 features of the Atmel ATmega 2560 AVR microcontroller (use the ATmega 2560 complete reference manual for help). B) List and describe two AVR instructions. As part of your description make sure that you list the operation for each instruction that is provided in the instruction set summary.
When an XIC instruction is cleared: a. This enables the next instruction (the rung-condition-out is true). b. This disables the next instruction (the rung-condition-out is false). c. The rung-condition-out is not scanned. d. The rung-condition-out is has to have an OTL.
Write a Verilog code with testbench for 16-bit up/down counter with synchronous reset and synchronous up/down.If up/down is set the counter is up counter and if it is not set, the counter is a down counter. submit the module code, testbench code, and the simulation results. PLEASE EXECUTE CODE IN VERILOG
1. Write the contents of all registers and the conditions codes registers after each execution instructions in Table Q1(a). Instructions SUBS r0, rl, 12 MOV 12,13, ASR #3 ro 11223344 Table Q1 (a) rl F7770025 12 r3 CF119856 CF119856 NZ V C 010 1
7.a. Weight and humidity are examples ofA. discrete outputs.B. discrete inputs.C. voltage signals.D. analog quantities. 7.b. What statement best describes the CPU scan?A. The data table is read, the inputs are updated, and the logic is solved.B. The fault table is cleared, the inputs are read, and the outputs are updated.C. The program scans for a "logic OK"; if the bit is set, the scan progresses.D. The input status is read, the program logic is solved, and the outputs are updated.