The position ontrud system uses unity feedbachand a plant trunsfer funchion10G4) =.s1 5+1)(S+P)be chosen by selechingtheThe parameter p Canaproprrate dc motor. Plot the root locus asa func hion of P. Select p so that the 2 af theComplex roots af the characteristic equation isapproximately Wz.

Answered: Image /qna-images/answer/3e4c6c1d-87e4-4e49-b923-9116c7ef0023.jpg

The posi tion Contrul system uses unity feedbouch and a plant trunsfer funchion 10 G) =. S15+1)(S+P) The parameter aproprrate de motor. Plot the root focus as a func tion of P. Select p so that the 2 af the x roots af the characteristic equation is p Can be chosen by selecting the comple a pproximately z.

The posi tion Contrul system uses unity feedbouch and a plant trunsfer funchion 10 G) =. S15+1)(S+P) The parameter aproprrate de motor. Plot the root focus as a func tion of P. Select p so that the 2 af the x roots af the characteristic equation is p Can be chosen by selecting the comple a pproximately z.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

find 1-transfer function of Dc Separately Excited motors (step by step). 2-Block diagram of Dc Separately Excited motors Ra La www mm Ia Va !Luw! GEH mm Tm, J, B,0
Electrical machine having 5 pole-pairs is supplied with 20 Hz. Peak value of induced back-emf is 120 V. Let's assume there is (0°) zero degrees between rotor and stator and at this moment peak back-emf is induced. What will be mechanical angle between rotor and stator in 0.03 seconds from that moment? What will be an induced back-emf in 0.03 seconds? Angle between rotor and stator deg Back-emf (use positive value) V
A250 V, dc. shunt mtor has an amature resistance of 0.5 chmand a field resistance of 250 dhm When driving a load of canstant tarque at 600 r.pm, the ammature current is 20 A If it is desired to raise the speed fram600 to 800 r.p.m, what resistance should be inserted in the shunt field circut? Assume that the magnetic circut is unsaturated
Electrical machine having 5 pole-pairs is supplied with 20 Hz. Peak value of induced back-emf is 120 V. Let's assume there is (0°) zero degrees between rotor and stator and at this moment peak back-emf is induced. What will be mechanical angle between rotor and stator in 0.03 seconds from that moment? What will be an induced back-emf in 0.03 seconds? Angle between rotor and stator deg
A Long-shunt dynamo running at 800 r.p.m suppLies 8 20hw at e a terminal voltage of 200 V. The resistances of the armature, shunt ficld and senes freld are o-05, lo0, and o.07n vespectively. The overall efficiemey at the above Load is 85.find cas Cu losses (b) dolRe tron and friction Losses ce) the torque excrted by the prime moter,
A DC motor is initially at rest and is then connected to a 12V battery. The motor has aresistance of 2 Ohms and an inductance of 0.5 Henrys. The motor has a torque constant of0.1 Nm/A and a back EMF constant of 0.1 V/(rad/s). Determine the current through themotor as a function of time, and the time it takes for the motor to reach 90% of its finalsteady-state speed.
4) A 40-kW induction motor, with a lagging power factor of 0.76 is supplied by a 120-Vrms, 60-Hz sinusoidal voltage source. Find the capacitance needed in parallel with the motor to raise the power factor to 0.9 lagging
The following figure shows a simplified endivi and inductor for a dc motor. The inductor has an average magnetic path length of 50 cm and a cross-sectional area of 12 cm2. The mean path length of the endivi is 5 cm and the cross-sectional area is given as 12 cm2. The air gap between the armature and the inductor is 0.05 cm, and the cross-sectional area of each air gap (including fringe effect) is 14 cm2. The magnetic permeability of the iron of the core is µr =2000 H/m and 200 turns are wound on the core. If the current through the conductor is set to be 1 A,a) What is the mmm force of the magnetic circuit?b) What is the reluctance of the inductor and armature?c) What is the magnetic flux density in the air gap?Is it Tesla?d) Calculate the inductance of the winding.e) If 10 turns of bandage are wrapped around the armature under these conditions,What is the torque to be induced if current A is passed?
Find the transfer function, 0L(s)/Ea(s), for the motor and load shown in the figure below. The torque-speed curve is given by Tm = -8wm + 200 when the input voltage is 100 volts. N1 = 20 edt) Motor N2= 100 N3 = 25 J= 1 kg-m2 D=5 N-m-s/rad DL = 800 N-m-s/rad N4= 10 JL = 400 kg-m2
8) A 230 V fed single quadrant chopper has a 40% duty cycle. A separately excited DC motor is controlled by a chopper. Motor has a back emf constant of 0.5 V/rad/s and 2 22 armature resistance. Determine the torque of motor at speed of 1400 rpm 4.7 N-m 15.44 N-m 10.5 N-m 19 N-m
(iv) If it's required to share the load by the three generators equally at the same bus- Three separately excited DC generators are connected in parailei to soply wtoo lond current of 1000A. The generators have the following parametera GI: R = 0.2 n, and induced E.M.F-200 V G2: Ra= 0.5 0, and induced E.M.F 250 V GS: R = 0.3 0, and induced E.M.F-220V %D Find Mathematically: (i) The armature current of each generator, (ii) The bus-bar voltage, (m) The power sharing by cach generator and the load power, (iv) bar voltage, what are your suggestions to achieve that?
Electrical Engineering Problem 4-1 DC Excitation of Induction Machine Consider a three phase induction motor in which stator phases b and c are con- nected to a de current source of amplitude Ide. Phase a is left disconnected. Use a stationary reference system with o = 0 and find: a) the stator d and q currents; b) the stator d and q steady state voltages if the rotor speed is constant at Or, (rad/sec); c) the rotor currents for the condition of part (b); d) the torque as a function of the de current, the rotor speed and the machine parameters.