The phase voltages across a certain load are given as: Va = 176 – j132 volts Vb = -128 - j96 volts Vc = -160 + j100 volts Va1 = 163.24-j35.10 / 166.97L-12.135 Va2 = 50.1-j53.9 / 73.59L-47.09 Va0 = -37.34-j42.67 / 56.70L-131.19 Compute for positive, negative, and zero sequence components of voltage.

The phase voltages across a certain load are given as: Va = 176 – j132 volts Vb = -128 - j96 volts Vc = -160 + j100 volts Va1 = 163.24-j35.10 / 166.97L-12.135 Va2 = 50.1-j53.9 / 73.59L-47.09 Va0 = -37.34-j42.67 / 56.70L-131.19 Compute for positive, negative, and zero sequence components of voltage.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

Use the information below to answer questions 24 und 25. The voltage across and the current through a load are (10+ j5Y and (2-jiArespecively. 24. What is the reactive power in VArconsumed? D. 0 A. 15 C. 20 D. 25 25. What is the pawer factor of the load? A. 0.8 leading B. 0.8 Jagging. -D. 0.6 ligging C 0.6 leading
A generator rated at 30MVA, 11kV has a reactance of 40%. Calculate its p.u. reactances for a base of 50MVA and 10kV. O 0.606 p.u. O 0.506 p.u. O 0.806 p.u. O 0.706 p.u.
6. What is the effect of load inductance on the ripple current? 7. i effect of chonnine Bock and boost 8. Wh 9 What chopping 10. At what duty evcle does the load current rinnle current he
The output voltage waveform of a four quadrant chopper is shown in figure. In the waveform, Vdc is input voltage, D is duty cycle ratio and T is cycle time. DT T. The RMS value of ripple component in output voltage is (A) Vác 2V VD-D (В) V(2D-1) (C) de de (D) V de VD- D? yd
Exercise-1 Vs = 240V 60Hz Is=10A/....... Power system Is ww R 1k0 Xc=-j/(2pi60x0.00016)=-1994 XL=ZL=j2pifl=j2pi60x0.142=j53.54 142mH Is=Ir+IL+Ic=.........=Vs/Ztotal=....... 160μF
Ererrises: IA platinum oil has a resifance of 3-14k r at go°C and 3.747JV at 100°C.- Fin'd the resistance at o'C ond the kmp -creff. of resifonce af 40°C 2. A pofential difference of r5oV is apphed to a field wnding at 15°C and the currend is SA. What will be the mean fempouafure of the winiding when currend has falen to 3.91A, apphedvrltage being constant Aasume s =p7.5. 3. A cril has a resi fance of 182 when its mean femperature is 20°C and 20v when ik mean femperature s 50°C. Frid is mean femperature rise when ik resotonce is 21JL and the sorrandinig femperature is i5°C. A cril of a relay takes a curre of 0.12 A when it is at the vem insbi o al 4. A jemperature of is'C ond canneckerdacms a oV supply If the minimum operating current of the relay is 0.1 A, colculate the femperature above ohich the relay will fail to operate when connected ti the same supply. Resi tncenfemp.coefficrenf of the cril makria] is o.0043 per °C at 0°C.
The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax
Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
4) Determine the value of voltage across resistor and capacitor5) Convert in rms values
2. The pu impedance of a circuit element is 0.15. If the base kV and base MVA are halved. Then the new value of pu impedance of the circuit element is A. 1.2 C. 1.1 3. The pu impedan B. 1.0 B. ambient tempera- ture D. 0.8 E. none
15. You are working on a power factor correction installation, and you notice with a clip-on ammeter as you add in capacitance the current drops, you add more capacitance and the current drops, you add more capacitance the current rises. How do you know when you are at unity power factor?
A DC-DC Chopper Circuit with an RL Load has an output current waveform shown below with a duty cycle of 50% and 1ms period. If it has a resistance of 1ohm and an inductance of 10mH, find the source voltage. 5A 2A ton toff output _current