* The permeameter in a perrneability test setup involves a soil sample 200 mm diameter and a length of 30 mm. The height of water is kept constant at 400 mm. In a duration of 4 min, water was collected in the graduated flask having a volume of 420 cu. cm. Determine the following. Flow Rate Hydraulic gradient o Hydraulic conductivity

* The permeameter in a perrneability test setup involves a soil sample 200 mm diameter and a length of 30 mm. The height of water is kept constant at 400 mm. In a duration of 4 min, water was collected in the graduated flask having a volume of 420 cu. cm. Determine the following. Flow Rate Hydraulic gradient o Hydraulic conductivity

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter6: Hydraulic Conductivity

Section: Chapter Questions

Problem 6.7P

See similar textbooks

Similar questions

The permeameter in a permeability test setup involves a sample 200mm diameter and a length of 30mm. The height of water is kept constant at 400mm. In a duration of 4 min, water was collected in the graduated flask having a volume of 450cu.m. Determine the Hydraulic Conductivity.
A sample of sand, 5 cm in diameter and 15 cm long, was prepared at a porosity of 60% in a constant-head apparatus. The total head was kept constant at 30 cm and the amount of water collected in 5 seconds was 40 cm^3. The test temperature was 20 deg C. Calculate the hydraulic conductivity. a. 6.7 x 10^-1 b. 3.47 x 10^-2 c. 5.0 x 10^-2 d. 2.0 x 10^-1
A sample of sand, 5 cm in diameter and 15 cm long, was prepared at a porosity of 60% in a constant-head apparatus. The total head was kept constant at 30 cm and the amount of water collected in 5 seconds was 40 cm^3. The test temperature was 20 deg C. Calculate the hydraulic conductivity. Provide a diagram a.5.0 x 10^-2 b.3.47 x 10^-2 c.2.0 x 10^-1 d.6.7 x 10^-1
Length of soil sample for constant head permeability test is 30 cm, Area of specimen is 177cm, constant head difference is 50 cm, total volume of water collected in 5 min is 350cm'. Calculate the hydraulic conductivity of the soil. A) 2.85x10'cm/sec D) 1.09x10 cm/sec 8) 1.09x10 cm/sec 9 3.95x10 cm/sec Answer A Submit
A constant head test is performed using a permeameter in the laboratory. The graduated cylinder collects 892 cm3 of water in 112 seconds. The soil specimen diameter = 18 cm , th elevation of water in upper-most piezometer is 181 com , the elevation of water in lowest piezometer is 116.6 cm and the piezometer inlets are evenly spaced at 16.7 cm on center. Compute the hydraulic conductivity, k and choose the correct answer below based on that. O A. 2.1 x 10^-3 cm/second O B. 1.5 x 10^-2 cm/second O C. 2.91 x 10^-2 cm/second O D. 2 x 10^-2 cm/second QUESTION 10 Given: -Applied stress on a soil = 122 kPa %3D -Influence Factor = 0.4 Compute the change in stress at 10 m below the edge of 25 m dimeter oil tank and select the correct answer from below: O A. Change in stress = 44 kPa O B. Change in stress = 49 kPa O C. Change in stress = 40 kPa O D. Change in stress = 42 kPa %3D
Question 2 * The permeameter in a permeability test setup involves a soil sample 200 mm diameter and a length of 30 mm. The height of water is kept constant at 400 mm. In a duration of 4 min, water was collected in the graduated flask having a volume of 420 cu. cm. Determine the following. Flow Rate o Hydraulic gradient o Hydraulic conductivity
1. For a constant head laboratory permeability test on a fine sand, the following values are given: Length of specimen, L = 10 inches Diameter of specimen = 2.5 inches Head difference, h = 22 inches Water collected in 2 minutes = 0.044 in %3D Soil specimen The void ratio of the specimen is 0.34. Determine the conductivity, k, of the soil in in/min. b. Ps ne a. Determine the discharge velocity through the soil in in/min. Determine the seepage velocity in in/min. Measuring hurket C.
A sand sample of 35m cm^2 cross sectional area and 20cm long was tested in a constant head permeameter. Under a head of 60 cm, the discharge was 120 ml in 6min. The dry weight of sand used for the test was 1120 g, and Gs= 2.68 A. Determine the hydraulic conductivity in cm/sec. B.Determine the discharge velocity in cm/sec. C. Determine the seepage velocity in cm/sec.
← Darcy' Law A sand sample of 35 m² cross sectional area and 20 cm long was tested in a constant head permeameter. Under a head of 60 km, the discharge was 120 ml in 6 min. The dry unit weight of sand used for the test was 1120 g. and GS = 2.68 Take Sw = 1 g/ cm³ The hydraulic conductivity (in cm/sec) is × 10-³ X
The Laboratory Apparatus shown maintains aconstant head in both the upper and lowerreservoirs. The soil sample is a silty sand with ahydraulic conductivity K = 5 x 10-3 cm/sec. and amoisture content of 18.5%. Specific gravity of soilsample = 2.70. Compute the seepage velocity.Determine the time required for the plug of water topass through the soil. Compute the discharge ofwater.
1. A 30cm long field sample is tested in a falling head permeameter with a 10 cm diameter cylinder. the diameter of the tube is 10mm. the water level in the tube is 35cm above the outlet level after one hour of operation, while the level drops to 22cm after 12 hours of operation. find the hydraulic conductivity of the sample.
A falling-head permeability test was carried out on a clay soil of diameter 100 mm and length150 mm. In 4 minutes the head in the standpipe of diameter 5mm dropped from 680 to 350mm. Calculate the hydraulic conductivity of this clay.