The intercepted areas between the output torque curve and the mean resistance line, taken in order from one end, are as follows : + 55, – 121, + 101, – 131, + 91, – 71 and + 76 mm?, when the engine is running at a speed of 10.33 r.p.s with the total fluctuation of speed is not to exceed ± 2% of the mean speed.Find the radius of gyration,when the rotating parts are equivalent to a mass of 45kgs and draw the turning moment diagram for a petrol engine with scale: Crank angle,1mm=3° Turning moment, 1mm=2N-m

The intercepted areas between the output torque curve and the mean resistance line, taken in order from one end, are as follows : + 55, – 121, + 101, – 131, + 91, – 71 and + 76 mm?, when the engine is running at a speed of 10.33 r.p.s with the total fluctuation of speed is not to exceed ± 2% of the mean speed.Find the radius of gyration,when the rotating parts are equivalent to a mass of 45kgs and draw the turning moment diagram for a petrol engine with scale: Crank angle,1mm=3° Turning moment, 1mm=2N-m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The turning moment diagram for a multi cylinder engine has been drawn toa scale of 1 mm = 4500 N -m vertically and 1 mm = 2. 4 ͦ horizontally. Theintercepted areas between output torque curve and mean resistance lineabove and below the mean taken in order from one end are 342, 23, 245,303, 115, 232, 227, 164 ??2, when the engine is running at 150 rpm. Ifthe mass of the flywheel is 1000 kg and the total fluctuation of speed doesnot exceed 3% of the mean speed, find the minimum value of the radius ofgyration.
The turning moment diagram for a multicylinder engine has been drawn to a scale of 1 mm = 4550 N-m vertically and 1 mm = 2.5° horizontally. The intercepted areas between output torque curve and mean resistance line taken in order from one end are 340, -24, 245, -305, 120,-232, 228, -165 mm2, when the engine is running at 180 r.p.m. If the mass of the flywheel is 1100 kg and the total fluctuation of speed does not exceed 4% of the mean speed, find the minimum value of the radius of gyration.
A gasoline engine working on four-stroke develops a brake power of 20.9 kW. A Morse Test was conducted on this engine and the brake power (kW) obtained when each cylinder was made inoperative by short circuiting the spark plug are 14.9, 14.3, 14.8 and 14.5 respectively. The test was conducted at constant speed. Find the indicated power, mechanical efficiency and bmep when all the cylinders are firing. The bore of the engine is 75 mm and the stroke is 90 mm. The engine is running at 3000 rpm.
ASAP
The turning moment diagram for the engine is drawn to the following scales: Turning moment, 1 mm = 1000 N-m and crank angle, 1 mm = - 6°. The areas above and below the mean turning moment line taken in order are : 530, 330, 380, 470, 180, 360, 350 and 280 mm². The mean speed of the engine is 150 r.p.m. and the total fluctuation of speed must not exceed 3.5% of mean speed. Determine the diameter and mass of the flywheel rim, assuming that the total energy of the flywheel to be 15/14 that of rim. The peripheral velocity of the flywheel is 15 m/s. Find also the suitable cross-scetional area of the rim of the flywheel. Take density of the material of the rim as 7200 kg/m³. [Ans. 1.91 m; 8063 kg; 0.1866 m²]
the torque-velocity (T/(w)) relations of the two machines with their shafts clamped together at constant voltage; T1(w)=a1-b1w a1=150Nm b1=1Nm . s/rad T2(w)=a2-b2w a2=270Nm b2=2Nm . s/rad friction will be neglected and there is also no load. question= Find the idle speed of the motors alone (not clamped).?
For the complex gear train shown, calculate the velocity ratio (VR). @2 = @3 W4 130 rpm N, = 45 N, = 90 N, = 80 %3D N3 = 20
Calculate the indicated power of a cylinder and the engine, if the mechanical efficiency of the engine is given as 75 % Calculate the brake power and friction power of the engine. Provide your answer in kW and hp. Study the power if the engine is a four stroke type. Cylinder bore 500 Piston stroke 2,050 Stroke/bore ratio Speed range Mean effective pressure = 2050/500 124-99 19.5 Maximum cylinder pressure Numbers of cylinders 5 to 8 Feedback: Correct answer = 155 mm mm rev/min bar bar
An engine develops 200 kW of power at a mean speed of 75 rpm. The coefficient of energy fluctuation is 0.15 and speed fluctuates within ±3% of the mean speed. Find the moment of inertia of the flywheel that must attached to the crankshaft of the engine in order to maintain the speedwithin the acceptable range.
Starter is used to transmit initial mechanical power to the car engine and the analysis will be based on this initial power input. Starter power is 1 hp, rotates at 250 rpm and has 10 teeth. The crankshaft has 48 teeth and camshaft has 60 teeth. Determine torque delivered by the camshaft? If the timing belt has 10 teeth/in, find its speed in in/min?
3. Determine the principal dimensions of a cone faced with leather to transmit 30 kW at 750 rpm from an electric motor to an air compressor. Sketch a sectional front view of the clutch and provide the main dimensions on the sketch. Assume: semi-angle of the cone = 12 1/2°; f = 0.2; mean diameter of cone = 6 to 10d where d is the diameter of shaft; allowable normal pressure for leather and cast iron = 0.075 to 0.1 N/mm²; load factor = 1.75 and mean diameter to face width ratio = 6.
2. A 75 kW induction motor runs at 740 rpm in clockwise direction. A 19 tooth helical pinion with20 degree normal pressure angle, 10 mm normal module and a helix angle of 23 degree is keyed to the motor shaft. Draw a 3-dimensional sketch of the motor shaft and the pinion. Show the forces acting on the pinion and the bearing at A and B. The thrust should be taken out at A All dimensions are in mm y 750 B 200 Z2=38 Z₁ = 19 X