The instruction "BTG 0x89,3,1" takes. instruction cycles to execute. If the default RC oscillator with Tosc = 32 uSec is used then this instruction take uSec to execute.
Q: 3. A relay coil has a resistance of 500 ohms and inductance of 10mH. The triggering current of relay…
A: Solution is attached with this notes.Thank you.
Q: If the vector R = 17.41 ap+ 16.83 a +5.13 az at (3.24, 357.37 degrees, 2.80) in cylindrical…
A:
Q: In a magnetic field, a coil with a resistance of 500 is placed. Determine the current at the coil at…
A: According to Faraday's Law of Electromagnetic induction, When a coil is placed in a time-varying…
Q: A 3-phase 25kVA, 220V alternator delivers rated kVA at a pf of 0.84. The effective resistance…
A: An electrical device that produces an alternating current is called an alternator. Utilizing a motor…
Q: The magnetic field intensity in free space is given as H = Ho sine ay A/m. where 0 = (wt-Bz) and ß…
A:
Q: Find the spectrum for the wave forms: 1 + 8 Sin (Gut) "t-2 @ vot
A: Given: v(t)=π(t-24)+8sin(6πt) To find the spectrum of the signal, we'll compute the Fourier…
Q: The symbol shown is for i Ţ O a. DPST O b. DPDT O C. SPDT d. SPST
A: Given, The symbol shown is
Q: Subject: Basic Electronics Can you please describe (in words) the following: 1.) CMOS 2.)…
A: 1. CMOS - The term CMOS stands for complementary metal-oxide semiconductor. The semiconductor…
Q: Find to in the network shown. 12 Τ Select one: O a. 4 mA ΙΚΩ O b. 3 mA Oc. None of them Od. 6 MA O e…
A: We need to find out the current for given circuit
Q: Obtain the form factor of a half rectified sinewave mm sine kn -ot
A:
Q: is the approximate center freque f the filter needed to pass the chosen ideband if the upper…
A:
Q: Using TDR, a pulse is transmitted down a cable with a velocity of propagation of 0.7c. The reflected…
A: Time Domain Reflectometer is an electronic system that tracks faults in metallic cables such as…
Q: In a balanced delta connected 30 circuit, the load in each branch consists of a 10 resistance in…
A: Given Data, Line Voltage VL=400 V Frequency f=50 Hz Resistance R=10 ohm Inductance XL=0.0318 H
Q: A meter whose constant is 600 revolution/ kwh makes 5 revolutions in 20 seconds . Calculate the load…
A:
Q: Calculate the current in the 5 resistor for the circuit shown below by source conversion technique.…
A: When modifying complicated circuits, source transformation techniques are employed to convert…
Q: A 150-m antenna, transmitting at 1.2 MHz (and therefore by ground wave), has an antenna current of 8…
A: Given,Transmitting ntenna height, hT=150mFrequency, f=1.2 MHzAntenna current, I=8ADistance,…
Q: A 2MVA, 2.3kV 3-phase Y-connected alternator operates at rated kVA at a power factor of 80%. The DC…
A:
Q: 5. When a power Pt is transmitted by an antenna, amount of energy incident on the target is given by…
A: The correct option along with the explanation is provided in the following section.
Q: An 8.0-mH inductor and a 2.0-02 resistor are wired in series to an ideal battery. A switch in the…
A:
Q: Find the voltage across the capacitor terminal at time 1 ms for the circuit below. R 10 Ω | 100 V C…
A:
Q: 5. For the following circuit, complete the timing diagram for the output (Y). Neglect hold time and…
A: A D Flip Flop is a type of digital electrical circuit that delays the state change of its output…
Q: 4. Which of the following is the correct relationship between temperature (T) and mobility (u) of…
A: The correct option along with the explanation is provided in the following section.
Q: Two concentric Gaussian surfaces encloses a charge. Which is correct? O The outer surface will have…
A: Gauss law : According to Gauss law electric flux passing through any enclosed surface is equal to…
Q: Assume Q = 0 initially and determine the waveform of Q for the NOR SR latch with the following…
A:
Q: 3. For the given latch, write down the truth table considering S, R, En and Q as inputs and Qnext…
A: The truth table of S-R latch En S R Qnext=output after sensing input data Q'next 0 X X No…
Q: Suppose black-and-white digital pictures are to be transmitted to the printer from a graphics source…
A: Given,The picture element per picture is,=2048×1024 pixelsThe intensity levels is,=64 levelsNumber…
Q: 4 a) Differentiate clearly between “intrinsic conduction” and “extrinsic conduction” in…
A: 4) (a) S.No. Intrinsic Conduction Extrinsic Conduction 1. Having low conductivity Having higher…
Q: V₁ + [-5..5] V e CHAPTER II-4. CONTROL OF MOTOR SPEED ERROR Controller Ge(s) Motor Position (V) Om…
A:
Q: what is kvl and kcl in circuit theory ?
A: The electrical circuit consists of various active and passive elements and The circuit calculations…
Q: In a short circuit test on a circuit breaker, the following readings were obtained on single…
A: Given in a short circuit test on a circuit breaker following readings, Time to reach the peak…
Q: For the below circuit, find io across the 24 ohms resistor. 40 ΩΣ + 10ΩΣ 24Ω{ v 30 Ω Σ... 8 A 36 ΩΣ…
A:
Q: 7. A microwave link consists of repeaters at 40-km intervals. What must be the minimum height of…
A:
Q: A capacitor in an LC oscillator has a maximum potential difference of 15V and a maximum energy of…
A:
Q: substation auxillaries
A: Transformer- A device that transfers the electrical energy between two electrical circuits which are…
Q: 12-9. Determine the SWR for a transmission line with maximum voltage standing-wave ampl Vmax = 6 V…
A: It is given that: Vmax=6 VVmin=0.5 V
Q: Suppose we are communicating on a cell phone using a digital modem at 9600 b/s. How many bits will…
A: Communicating on a cell phone using a digital modem at 9600 b/s
Q: 1. Which of the following is not an electronic device? a) A mobile b) A computer c) A magnifying…
A: The solution is provided in the following section.
Q: The electric field in the region is given as E= meters. x²x2 + measured in volts per meter. Find the…
A:
Q: Consider an ideal MOS capacitor with p-type silicon biased into depletion. Let x = 0 be at the…
A: Considering an ideal MOS capacitor with p-type silicon biased into depletion. Let x=0 be at the…
Q: 1. Which of the following is not an electronic device? a) A mobile b) A computer c) A magnifying…
A: mobile , keyboard and computer are design by semiconductor devices like BJT ,MOSFET, Amplifier .
Q: ZL = 50 52. for a 75-92 transmission line that is terminated in a lo
A:
Q: Determine Vout. +30 V Vin OV -30 V Vout at Vin = +30V = Vout at Vin = -30V = 2.2 ΚΩ 12 V- +1₁ V V…
A: Given: Circuit diagram
Q: Determine Vout. +30 V OV -30 V Vin www 2.2 ΚΩ v 12 V t Vout
A:
Q: Given u(t)=step(t) and h(t)=exp(-alpha t). a) perform convolution using different methods b) use…
A:
Q: 1. The circuit in the figure is a half-wave rectifier whose input is sinusoid vin(t)=sin wt and its…
A:
Q: esign consideratio of electrical installation system for commerical building
A: According to the question, we need to discuss the design consideration of the electrical…
Q: An 11 kV, 100 MVA alternator is provided with differential protection. The percentage of winding to…
A:
Q: 1. Which of these is incorrect for an operational amplifier?
A: The correct option along with the explanation is provided in the following section.
Q: Using Mesh analysis, find i1 in Amperes if Vs = 15.1 V and R = 4.8 Ohm.
A: It is given that: Vs=15.1 VR=4.8 ohm
Q: Explain why sometimes Customer Average Interruption Duration Index (CAIDI) increases when redundancy…
A:
Trending now
This is a popular solution!
Step by step
Solved in 3 steps
- III) Convert from Hexadecimal to Decimal (a) 1ACED716 (b) C1AC18A.E8B916 IV) Convert Decimal to Hexadecimal (a) 114510 (b) 3176.54101. Consider the CRC generator shown below. Determine the output of the CRC circuit (i.e. Q4 Q3 Q2 Q1 Q0, expressed as a decimal number) for the input sequence "1010" (input one bit at a time, left to right). Assume the CRC circuit is initialized to state 11111. D Q0 Q2 Q4 Q1 Q3 Clock - Data In1-Write microprocessor program using mnemonics to add two numbers 08 and 06. 2-Write the object code of the program. 3-Perform the program using STEP function. 4-Execute the program and write the results. Object code Mnemonics MOV AX A1 B0 MOV AL B3 MOV BL 04 ADD AL F4 HLT
- There exists one or more discrete ime signal. What is it control system ? (a) discrete time or (b) continuous timeA 9-bit asynchronous counter has a 128-kHz clock signal applied. (1) What is the MOD number of this counter? MOD number = (ii) What will be the frequency at the MSB output? fmsb = (iii) Assume that the counter starts at zero. What will be the count after 635 input pulses? After 635 input pulse, Count =Assume a block diagram for a clock divider that can take a 1 MHz oscillator and create a signal that has clock frequency of 20 Hz. What is the terminal count value needed to create this frequency and the number of bits needed on the counter if the clock divider can select between a 20 Hz signal and 2 kHz signal?
- Design an encoding matrix with diodes and resistors to display a decimal number to on the seven-segment display. You have 10 switches (WO-W9) with one terminal connected to Vec. For decimal number 0, switch 0 (S0) is closed, for decimal number 1, switch 1 (S1) is closed etc. (Switches are on the vertical axis, S0 on top and the outputs are taken on the horizontal axis (Y0-Y6), with “a" on the left and "g" on the right. Note that (Y0-Y6) outputs are used as inputs to seven-segment display. Since these outputs cannot drive the seven segment display LEDS you may need additional bipolar transistors and resistors. The supply voltage is 5V and each LED needs a current of 20mA. Note that this is a design problem and the design is not unique. Do your best! f a a eTo reset IC chips in a system at power-on, the chips must be powered on and working already. That is to say that the reset signal needs to be after the power-on time. Assume that you need to generate a reset signal 1 ms after power-on using an RC circuit, what will be roughly the values of the resistor and capacitor?4. The following Data input and data select waveforms are applied to a Multiplexer. Determine the output waveform. Do D Dy So