The inner surface temperature of a 23 cm thick wall of an oven is 820°C, and the outer surface temperature is 170°C. When kept constant, the heat loss of the furnace is measured as 2450 W/m2 from m2 of the wall. heat of the wall Calculate the transmission coefficient

The inner surface temperature of a 23 cm thick wall of an oven is 820°C, and the outer surface temperature is 170°C. When kept constant, the heat loss of the furnace is measured as 2450 W/m2 from m2 of the wall. heat of the wall Calculate the transmission coefficient

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.60P

See similar textbooks

Similar questions

2.38 The addition of aluminum fins has been suggested to increase the rate of heat dissipation from one side of an electronic device 1 m wide and 1 m tall. The fins are to be rectangular in cross section, 2.5 cm long and 0.25 cm thick, as shown in the figure. There are to be 100 fins per meter. The convection heat transfer coefficient, both for the wall and the fins, is estimated to be K. With this information determine the percent increase in the rate of heat transfer of the finned wall compared to the bare wall.
1.60 Two electric resistance heaters with a 20 cm length and a 2 cm diameter are inserted into a well-insulated 40-L tank of water that is initially at 300 K. If each heater dissipates 500 W, what is the time required for bringing the water temperature in the tank to 340 K? State your assumption for your analysis.
Determine the rate of heat transfer per meter length to a light oil flowing through a 2.5-cm-ID, 60-cm-long copper tube at a velocity of 0.03 m/s. The oil enters the tube at 16C, and the tube is heated by steam condensing on its outer surface at atmospheric pressure with a heat transfer coefficient of 11.3 kW/m K. The properties of the oil at various temperatures are listed in the following table: Temperature, T(C) 15 30 40 65 100 (kg/m3) 912 912 896 880 864 c(kJ/kgK) 1.80 1.84 1.925 2.0 2.135 k(W/mK) 0.133 0.133 0.131 0.129 0.128 (kg/ms) 0.089 0.0414 0.023 0.00786 0.0033 Pr 1204 573 338 122 55
A cooling system is to be designed for a food storage warehouse for keeping perishable foods cool prior to transportation to grocery stores. The warehouse has an effective surface area of 1860 m2 exposed to an ambient air temperature of 32C. The warehouse wall insulation (k=0.17W/(mK)) is 7.5 cm thick. Determine the rate at which heat must be removed (W) from the warehouse to maintain the food at 4C.
1.19 A cryogenic fluid is stored in a 0.3-m-diameter spherical container is still air. If the convection heat transfer coefficient between the outer surface of the container and the air is 6.8 , the temperature of the air is 27°C, and the temperature of the surface of the sphere is –183°C, determine the rate of heat transfer by convection.
1.67 In beauty salons and in homes, a ubiquitous device is the hairdryer. The front end of a typical hairdryer is idealized as a thin-walled cylindrical duct with a 6-cm diameter with a fan at the inlet that blows air over an electric heating coil as schematically shown in the figure. The design of this appliance requires two power settings, with which the air blown over the electric heating coil is heated from the ambient temperature of to an outlet temperature of and with exit air velocities of 1.0 m/s and 1.5 m/s. Estimate the electric power required for the heating coil to meet these conditions, assuming that heat loss from the outside of the dryer duct is neglected.
3.16 A large, 2.54-cm.-thick copper plate is placed between two air streams. The heat transfer coefficient on one side is and on the other side is . If the temperature of both streams is suddenly changed from 38°C to 93°C, determine how long it takes for the copper plate to reach a temperature of 82°C.
Steam at a temperature of 200 °C flows through a pipe of 5 cm inside diameter and 6 cm outside diameter. The length of the pipe is 30 m. If the steady rate of heat loss per unit length of the pipe is 2 W/m, calculate the heat fluxes at the inner and outer surfaces of the pipe. (12.7 W/m²; 10.6 W/m²)
A pipe 30 m long with an outer diameter of 75 mm is used to deliver steam at a rate of 1500 kg / hour. The vapor pressure is 198.53 kPa entering the pipe with a quality of 98%. The pipe needs to be insulated with a thermal conductivity of 0.2 W / (m K) so that the quality of the steam will only slightly decrease to 95%. The outer surface temperature of the insulation is assumed to be 25 ° C. Ignore resistance conductive of the pipe material and it is assumed that there is no pressure drop in the pipe. a. Determine the enthalpy of incoming vapor = Answer kJ / kg. b. Determine the enthalpy of steam coming out = Answer kJ / kg. c. Determine the vapor heat change / loss along the flow = Answer watt. d. Specify the minimum required insulation thickness = Answer cm.
The wall of an oven in an industrial plant, made of fire brick (k = 0.71 W/m/K) has thickness of L = 15 cm. The oven is exposed to air at 28oC and the surfaces of the far surroundings are at 20oC. If the temperature of the outer surface of the wall is 92oC and the heat transfer coefficient and emissivity are 20 W/(m^2*K) and 0.8 respectively, determine the temperature of the inner surface of the wall.
A pipe 30 m long with an outer diameter of 75 mm is used to deliver steam at a rate of 1500 kg / hour. The steam pressure is 198.53 kPa entering the pipe with a quality of 98%. The pipe that needs to be insulated with a thermal conductivity of 0.2 W / (m K) so that the quality of the steam only decreases slightly to 95%. The temperature of the outer surface of the insulation is assumed to be 25 ° C. The conductive of the pipe material and the situation of no pressure drop in the pipe. A. Determine the enthalpy of incoming vapor = Answer kJ / kg. b. Determine the enthalpy of steam that comes out = Answer kJ / kg. c. Determine the change / loss of steam heat along the flow = Answer watt. d. Determine the minimum required insulation thickness = Answer cm.
The furnace wall shown in the figure is made of a material with a thermal conductivity of 5 W / m ° C, the radiant emission coefficient of the outer surface of the wall is 0.95, Stefan Boltzman constant is 5.67x104 W / m ^ 2 (K ^ 4), ambient temperature and air temperature 297 K is. The heat transfer coefficient between the outer surface of the wall and the air is h = 20 W / m (K ^ 2). Wall inner surface temperature 573 K, outer surface temperature 308 K Since the value is kept constant a) Find the layer thickness of the wall? b) Find the layer thickness of the wall if the moving fluid medium on the outer surface of the wall is corroded?