The industrial truck is used to move the solid 1200- k roll of paper up the 30° incline. If the coefficients of static and kinetic friction between the roll and the vertical barrier of the truck and between the roll and the incline are both 0.40, compute the required tractive force P between the tires of the truck and the horizontal surface.

The industrial truck is used to move the solid 1200- k roll of paper up the 30° incline. If the coefficients of static and kinetic friction between the roll and the vertical barrier of the truck and between the roll and the incline are both 0.40, compute the required tractive force P between the tires of the truck and the horizontal surface.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.24P: A uniform plank is supported by a fixed support at A and a drum at B that rotates clockwise. The...

See similar textbooks

Similar questions

The block of weight W is pulled by the force P inclined at the angle to the horizontal. Find the smallest force P and the corresponding angle that would cause impending sliding of the block. The angle of static friction between the block and the ground is s.
A uniform plank is supported by a fixed support at A and a drum at B that rotates clockwise. The coefficients of static and kinetic friction for the two points of contact are as shown. Determine whether the plank moves from the position shown if (a) the plank is placed in position before the drum is set in motion; and (b) the plank is first placed on the support at A and then lowered onto the drum, which is already rotating.
Calculate the horizontal force P required to push the 85-lb lawn mower at constant speed. The center of gravity of the mower is at G, and the coefficients of rolling resistance are 0.12 for the front wheels and 0.18 for the rear wheels.
The 2225 N block shown is in contact with 45° incline. The coefficient of static friction is 0.25. Compute the value of the horizontal force P necessary to a. just start the block up the incline b. just prevent motion down the incline c. If P = 1780 N, what is the amount and direction of the friction force?
1.The figure shows 3 blocks. Block C hangs from a rope which passes through a fixed cylinder and is attached to block B. Find the maximum mass of block C so that block B does not move to the right. Take into account that there are frictional forces at all points of contact. Consider the given values of the masses and , the coefficient of static friction between surfaces µ1 and the coefficient of friction static between the cylinder and the uC chord. Here are the values: ma= 72 kg mb= 62 kg u1= 0,47 uC=0,37
2. Compute the horizontal force P required to prevent the block from sliding down the plane for the 100 lb block shown. Assume the coefficient of static friction to be 0.65. 30° W = 100 lb MRSM
1. A 5.0kg steel block is resting on a horizontal table. The coefficient of static friction is 0.75 and coeficient of kinetic friction is 0.57. What is the maximum force that can be applied horizontally before it starts to move? 2. Three drums stacked as shown. Considering the weight of the drums and friction in all contact surfaces, how many forces are there in the FBD of A? (Friction and normal forces are treated separately.) (*see first image for the figure) 3. How many components (forces and couples) does a fixed support in 3D contain? (*see second image for the figure)
A 150 lb man stands on a 60 lb bar to which the cable is tied at B. The cable passes over two fixed pegs with coefficient of frictions as indicated. You may treat the cable the same as you would treat a flexible flat belt. assume the normal force exerted by the man in the bar acts downward through point A. Find the smallest force the man can exert on the cable if the bar is to remain horizontal.
Required information A photograph of the NASA Apollo 16 Lunar Module (abbreviated by NASA as the LM) is shown on the surface of the Moon. Such spacecraft made six Moon landings during 1969 - 72. A simplified model for one of the four landing gear assemblies of the LM is shown. Assume the weight of the LM is uniformly supported by all four landing gear assemblies, and neglect friction between the landing gear and the surface of the Moon. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. A (2.5, 2.5, -2.2) m B (1.5, 1.5,0) m C(2, 1,-1.2) m D(1,2,-1.2) m Z B D If the LM has 14950 kg mass and rests on the surface of the Moon where acceleration due to gravity is 1.62 m/s2, determine the forces supported by members AB, AC, and AD. (Round the final answers to four decimal places. Include a minus sign if necessary.) The forces supported by members AB, AC, and AD are as follows: TAB 10621 N TAC= 2903 N TAD 6032 N
5. A box with a mass of 100 kg was originally attached to the spring at position A. After that, pressure was applied to the box until The spring compresses to a distance of X - 1 m and releases it, causing the box to move upwards along the inclined floor. If the incline has and = the coefficient of friction uk = 0.3, find the box that can travel along the incline for a maximum distance in meters.
Problem 4. A.) If the uniform concrete block has a mass of 500 kg, determine the smallest horizontal force P needed to movethe wedge to the left. The coefficient of static friction between the wedge and the concrete and the wedge and the floor is 0.3. The coefficient of static friction between the concrete and floor is 0.5.ANSWER: P=1797.52; N=1.80kNB.)Refer to problem number 4. Calculate the followinga.) the angle of friction between the wedge and the concrete and the wedge and the floor.Answer: ?????? ??? ????????= ?????? ??? ?????= 16.7ob.) the coefficient of static friction between the concrete and floor.Answer: ????????? ??? ?????= 263.56o
1. Find the least value of P required to cause the system of blacks shown to have impending motion to the left. Also find the normal forces on each block. The coefficient of friction under each block is 0.20 and angle alpha is 25 degrees. CIL 30 kN 10 kN 30