The guy wires AB and AC are attached to the top of the transmission tower. The tension in cable AB is 8.2 kN. Determine the required tension T in cable AC such that the net effect of the two cables is a downward force at point A. Determine the magnitude R of this downward force. Assume a 30 m, b = 41 m, c = 24 m, and d = 34 m. B

The guy wires AB and AC are attached to the top of the transmission tower. The tension in cable AB is 8.2 kN. Determine the required tension T in cable AC such that the net effect of the two cables is a downward force at point A. Determine the magnitude R of this downward force. Assume a 30 m, b = 41 m, c = 24 m, and d = 34 m. B

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter11: Magnetic Forces And Fields

Section: Chapter Questions

Problem 101AP: Unreasonable results Frustrated by the small Hall voltage obtained in blood flow measurements, a...

See similar textbooks

Similar questions

x component y conponent z component = 204.44 = 255.5 = 472.78 Knowing that the tension is 555 lb in cable AB and 470 lb in cable AC, determine the magnitude and direction of the resultant of the forces exerted at A by the two cables. y 45 in. 40 in. 60 in. 60 in. D The magnitude of the resultant of the forces at A is The angle defining the direction of the resultant force exis The angle defining the direction of the resultant force @yis[ The angle defining the direction of the resultant force 8, is lb.
A rectangular plate is supported by three cables as shown. Knowing that the tension in cable AC is 669 N, determine the weight of the plate. Given that L1 = 349 mm, L2 = 266 mm and L3 = 526 mm. L3 130 320 450
Three cables are connected at A, where the forces P and Q are applied as shown. Determine the tension in each cable knowing that P = 3080 N and Q = 596 N. 320 mm 380 mm B y 220 mm 960 mm 960 mm The tension in cable AB is The tension in cable AC is The tension in cable AD is N. N N. 240 mm X
The system represented in the figure is in balance.Determine the voltages on wires 1, 2 and 3 and the value ofangle θ.answer:T1 = 1.960N; T2 = 1.697N; T3 = 3.394N; θ = 60°
Physics students, wanted to investigate the forces of attraction (F) between two parallel conductors carrying currents li and l2 (also known as Ampere's Law) The students noticed that as the length of the parallel conductors (/) was increased the force of attraction between the conductors (F) also increased. The data collected is in the |L= SA conductor 1 average separation (d = 0.50m) table: conductor 2 Length, / (m) Force, F (x 10-5 N) 12= 5A 1.00 9.00 1.20 10.8 1.40 12,5 1.60 14.2 1.80 16.2 (iii) On the grid plot the force and length values from the table. (iv) Draw the line of best fit (v) Find the slope of the line of best fit. (c) Use the slope calculated and the Ampere's Law equation to determine the experimental value of the magnetic force constant, k.
The mass of the cylinder is 50 kg. 0 = 65 degrees B Ө Ө The tension in the cable AC is most nearly:
Two resistanceless rails rest 42 cm apart on a 6.6o ramp. They are joined at the bottom by a 0.68 Ω resistor. At the top, a copper bar of mass 0.034 kg (ignore its resistance) is laid across the rails. The whole apparatus is immersed in a vertical 0.35 T field. What is the terminal (steady) velocity of the bar as it slides frictionlessly down the rails?
For the following equilibrium system, assuming all strings are ideal. If the mass M = 50, and the angles B and 0 are 50 ° and 30 °, respectively. What is the value of the magnitude of the voltage T4? T3 O T2 M a) T4 = 762.3042 N b) T4 = 980 N c) T4 = 565.8035 N d) T4 = 639.6499 N
Physics students, wanted to investigate the forces of attractioh (F) between two parallel conductors carrying currents l1 and l2 (also known as Ampere's Law) The students noticed that as the length of the parallel conductors (/) was increased the force of attraction between the conductors (F) also increased. The data collected is in the |L= 5A conductor 1 average separation (d 0.50m) table: conductor 2 Length, I (m) Force, F (x 106 N) 12 = 5A 1.00 9.00 1.20 10.8 1.40 12,5 1.60 14.2 1.80 16.2 (iii) On the grid plot the force and length values from the table. (iv) Draw the line of best fit (v) Find the slope of the line of best fit. (c) Use the slope calculated and the Ampere's Law rmine the experimental value of equation to de the magnetic force constant, k.
A straight rod moves along parallel con- ducting rails, as shown. The rails are con- nected at the left side through a resistor so that the rod and rails form a closed rectangu- lar loop. A uniform field perpendicular to the movement of the rod exists throughout the region. Assume the rod remains in contact with the rails as it moves. The rod experiences no friction or air drag. The rails and rod have negligible resistance. 3.7 T 3.7 T At what speed should the rod be moving to produce the downward current in the resistor? Answer in units of m/s. 0.39 A – ® 7.6 g 1.6 m
14.32 Label the directions and mark the po- larities for the six unique currents in the cir- cuit below. Then use Kirchhoff's rules to set up six independent equations that can then be solved for the unknown currents. a 25.0 Ω www 10.0 Ω wwww www. 3.5 Ω + 15.5 V 10.0 Ω www wwww 5.0 22 b Figure 14.49: A bridge circuit with five resis- C tors. BLO
1.8 Cast-steel Cross-sectional pap1 = 0.5 mm. area -3 cm? 1.6 l4 = 10 cm Silicon iron Cast iron 1.4 Mild steel 1.2 Cross-sectional area 32 ст? 1.0 0.8 Cast iron Cross-sectional area-1.4 cm? = 0.1 mm 0.6 (a) 0.4 0.2A 1000 2000 3000 4000 5000 6000 7000 Magnetic field strength, H(A/m) (b) Figure (1) Silicon Iron uɔ S7 = "1 Flux density, B(T)