The following data are obtained for 7.5 hp, 28A, 4-pole, 208V, 60Hz, Y-connected stator squirrel cage three-phase induction motor. DC Test: Voc = 13.6V , Ioc= 28A No-Load Test: Vt= 208V , IA= 8.12A , Pout= 420W Locked-Rolot Test: Vt=25V , IA= 28A , Pin = 920W Calculate the per-phase equivalent circuit parumeters of this motor referred to the stator side. ?????

The following data are obtained for 7.5 hp, 28A, 4-pole, 208V, 60Hz, Y-connected stator squirrel cage three-phase induction motor. DC Test: Voc = 13.6V , Ioc= 28A No-Load Test: Vt= 208V , IA= 8.12A , Pout= 420W Locked-Rolot Test: Vt=25V , IA= 28A , Pin = 920W Calculate the per-phase equivalent circuit parumeters of this motor referred to the stator side. ?????

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter32: Three-phase Motors

Section: Chapter Questions

Problem 6RQ: Name three factors that determine the torque produced by an induction motor.

See similar textbooks

Similar questions

A freewheeling DC motor is driven with 1000 rpm and a nominal load torque of 80Nm. The field circuit resistance is 200 and the armature circuit resistance is 0.2 O. The field coils are fed with a zero degree transmission angle through a single-phase fully controlled converter connected to a single-phase 240V source. The armature circuit is fed from a single phase 400V source through another fully controlled converter. Magnetic saturation has been neglected, the motor constant is given as 0.8 V - s / A - rad. Assuming that there is no fluctuation in armature and field current, find the control angle of the converter feeding the armature at nominal load. If you want to leave the question blank, click again on the option you marked.
An 8 pole, 50 Hz slip ring induction motor runs at a slip of 2.67% on full load. The rotor resistance per phase of the winding is 0.2 ohm. What external resistance per phase must be added in the rotor circuit so that the motor now runs ate a slip of 17.33% such that the torque remains same in both the cases. (Ans: 1.1 ohm)
A 110 V, 60 Hz, 6 – pole single phase induction motor 1/3 hp has the following equivalent circuit impedances: RI = 1.52 ohm, R2 = 3.13 ohm and x1 =2.10 ohm, x2 =1.56 ohm. Xm=58.2 ohm, The Friction, windage and stry losses =16W, the core loss = 35 W, For a slip of 0.05, calculation (a) input current, (b) power factor, (c) developed power, (d) output power, (e) speed (f) in put power (g) air gab power (h) T ind (i) T load 6) efficiency.
c) What is the physical meaning for each of the following induction motor parameters: R1 „R2 ,Rc ,X1 ,X2 ,Xm ?
A 125-hp, 480-V, 50-Hz, 6-pole, Y-connected induction motor has the per-phase equivalent circuit parameters as follows: Nominal code Locked rotor, letter kVA/hp R = 0.15 2 R2 = 0.10 2 X1 = 0.360 X2 = 0.36 2 C 3.55 – 4.00 =8.362 D 4.00 – 4.50 E 4.50 – 5.00 F 5.00 – 5.60 The core-losses are 1.7 5.60 – 6.30 kW, mechanical losses are 1.8 kW, and stray losses are 50 W. a) b) Calculate the speed at the pullout torque in rpm, the pullout torque, and the starting torque using exact Thevenin parameters. c) Find the starting code letter assigned to this motor.
A 480V, 60 Hz, 6-pole, three-phase, delta-connected induction motor has the following parameters: R₁=0.461 2, R₂=0.258 2, X₁=0.507 92, X₂=0.309 Q, Xm-30.749 Rotational losses are 2450W. The motor drives a mechanical load at a speed of 1170 rpm. Calculate the following information: i. Synchronous speed in rpm ii. iii. iv. V. vi. vii. viii. slip Line Current Input Power Airgap Power Torque Developed Output Power in Hp Efficiency
Q2] Fill in the blank (9 Marks) 1-The current drwan by the armature of D.C. motor is directly proportional to 2- The speed of a D.C. shunt-wound motor will shunt field regulator is increased. 3- The synchronous speed of a three-phase induction motor is number of pairs of poles. Rotor copper losses Rotor input power in induction motor = 5- A 4-pole three-phase induction motor has a synchronous speed of 25 r.p.s. The frequency of the supply to the stator is_ Hz. 6- The power input to a mains transformer is 200VA. If the primary current is 2.5A, the secondary voltage is 2V and assuming no losses in the transformer, the turns ratio step down. is 7- A 200kVA transformer has an iron loss of 1 kW and full load cu loss of 2 kW. Its load kVA corresponding to maximum efficiency is kVA. 8- If cu loss of a transformer at 7/8th full load is 4900 W, then its full-load cu loss would be watt. 4- if the value of resistance of the proportional to the 9- The slight curvature at the lower end of the open…
A 3 – phase induction motor has a 4 – pole, star – connected stator winding. The motorruns on a 50 – Hz supply with 200 V between lines. The rotor resistance and standstillreactance power phase are 0.1 and 0.9 ohm respectively. The ratio of rotor to stator turnsis 0.67. Calculate (a) total torque at 4 % slip, (b) total mechanical power at 4 % slip, (c)maximum torque, (d) speed at maximum torque, (e) maximum m power
Two identical 3-phase, 500-V induction machines are mechanically coupled for a back-to-back test. One machine is motoring from a 500-V, 50-Hz supply and the other is generating on to a 3-phase, 500-V synchronous machine for which the fre- quency can be controlled. It is required to run the motoring induction mạchine at 40 hp. Neglecting the slight change in the generating machine parameters due to oper- ating at a reduced frequency, estimate the rating of the synchronous machine for this duty and the frequency at which it must be run. Line input readings for each machine No load 500 V 8.5 A 1-6 kW Locked rotor 100 V 30 A 1-6 kW Friction and windage loss per machine 0-8 kW. R = R2'
L-1). The 3-phase wound-rotor induction motor has .... . a) high starting torque b) low starting current c) both "a" and "b" d) neither "a" nor "b" L-2). The 3-phase wound-rotor induction.........a) motor has a wire wound rotor b) motor's rotor can be connected to an external resistive load by way of slip rings and brushes c) motor requires more maintenance than the 3-phase squirrel-cage induction motor d) all of the above L-3). The 3-phase wound-rotor induction motor's rotor circuit's resistance should be adjusted so it is__________ during starting. a) low b) high c) either "a" or "b" d) neither "a" nor "b" L-4). Will a 3-phase wound-rotor induction motor start with no external circuit connected to its rotor leads? a) yes b) no
7- A 6-pole, 50-Hz, 3-0 induction motor is running at 950 rpm and has rotor Cu loss of 6 kW. Its rotor input is......kW (a) 120 (b) 60 (c) 6.3 (d) 66 8- The number of slip rings on a squirrel cage induction motor is usually (a)Two (b) Three (c) Four (d) None
A 220 V, 50 Hz, 4-Pole, 1410 rpm, single phase induction motor has the following parameters: R₁ = 9.5 Q, X₁ = 12 Q, R₂ = 10.8 Q, X2 = 12 2, and XM = 260 Q. At rated speed the core loss is 30W, and the friction and windage loss is 15W. The motor is connected to a single phase 220V, 50 Hz and runs at the rated speed. Determine: the slip, motor current, power factor, input power, developed torque, output shaft power, shaft torque, efficiency, rotor frequencies, rotor copper losses, and the ratio of forward flux to the backward flux.