Three single-phase transformers (ideal) are connected as shown inthe figure below to supply a balanced 3-phase, 150 KVA, 600 VLload from primary 4.16 KVLLline.H1X1H2X2BALLANCEDH1X1THREE PHAGELOADH2X2H1X1X2(a)Draw (neatly) a phasor diagram showing the three, primaryline-to-line voltages and the six secondary phase and linevoltages. What is the phase relationship between the primaryvoltage VAB and the secondary voltage V12? Indicate on thephasor diagram:f

Please find your answer below in step 2

the figure below to supply a balanced 3-phase, 150 KVA, 600 VLL load from primary 4.16 KVLL line. BALLANCED THREEPHAGE H1 X1 LOAD HI X1 (а) Draw (neatly) a phasor diagram showing the three, primary line-to-line voltages and the six secondary phase and line voltages. What is the phase relationship between the primary voltage VAB and the secondary voltage V12? Indicate on the phasor diagram: 空

the figure below to supply a balanced 3-phase, 150 KVA, 600 VLL load from primary 4.16 KVLL line. BALLANCED THREEPHAGE H1 X1 LOAD HI X1 (а) Draw (neatly) a phasor diagram showing the three, primary line-to-line voltages and the six secondary phase and line voltages. What is the phase relationship between the primary voltage VAB and the secondary voltage V12? Indicate on the phasor diagram: 空

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.56P: Three single-phase two-winding transformers, each rated 3kVA,220/110volts,60Hz, with a 0.10 per-unit...

See similar textbooks

Similar questions

Three single-phase two-winding transformers, each rated 3kVA,220/110volts,60Hz, with a 0.10 per-unit leakage reactance, are connected as a three-phase extended autotransformer bank, as shown in Figure 3.36(c). The low-voltage winding has a 110 volt rating. (a) Draw the positive-sequence phasor diagram and show that the high-voltage winding has a 479.5 volt rating. (b) A three-phase load connected to the low-voltage terminals absorbs 6 kW at 110 volts and at 0.8 power factor lagging. Draw the per-unit impedance diagram and calculate the voltage and current at the high-voltage terminals. Assume positive-sequence operation.
In developing per-unit equivalent circuits for three-phase transformers. under balanced three-phase operation. (i) A common Sbase is selected for both the H and X terminals. (ii) The ratio of the voltage bases Vbase/VbaseX is selected to be equal to the ratio of the rated line-to-line voltages VratedHLL/VratedXLL. (a) Only one of the above is true. (b) Neither is true. (C) Both statements are true.
In per-unit equivalent circuits of practical three-phase transformers, under balanced thr-phase operation, in which of the following connect ions would a phase-shifting transformer come up? (a) Y-Y (b) Y- (c) -
Connect three single-phase transformers in Y-Y, with subtractive polarity, so that the line-to-line voltages on the primary are 30 degrees delayed to their respective line-to-line voltages on the secondary. It should show each step that is needed to make this connection (example: the phasor diagram) and should show the final connection of the three transformers including the polarity markings. Assume phase A on the primary is terminal "H1".
In the system shown in Figure 1, the transformers are connected star-star with both star points grounded and the generators are connected in star with thier star points grounded. The system base is 15 MVA. The transformers all have reactances of 0.04 p.u. on this 15 MVA base. The reactances of all other elements are given in Table 1 (in 2) and the voltage levels are given in Table 2. p.u. G1 p.u. T1 jö Per-Unit Convert all values to p.u. on a 15 MVA base. Xa= p.u. Xc₂= XL = V BABE G1 2 X 9 T3 Figure 1: A section of the distribution system T1 L Table 1: Sequence reactances (2) 3 G1 L G2 0.3 0.59 0.01 4 L 9/10 10 Fault Voltage What is the voltage at bus 3 (in Volts) after the fault has occurred? Vp= V T2 5 T2 34 10/4 Table 2: Voltage bases (kV) G2 4 T3 10/9 | G2 Fault Current A three-phase fault with a fault reactance of 0.01 p.u. occurs at bus 3. Calculate the fault current flowing at the fault point in KA. Ip=-j KA So
a)Why are transformers generally connected in parallel at a substation?b)What conditions must be met for two transformers to be paralleled?c)Draw the phase relationship and connection diagram for Dd0 connection andYy6
What are the conditions for the parallel operation of 1-phase transformers?
2- Draw and explain the phasor diagram for two transformers in parallel.
Three single phase transformers each having a 240 V primary and two 250 V secondaries, as shown in the figure below, is to be connected to a 400 V, 3–phase supply to give a six phase output. A d e В f Show how this is done and find the voltage between adjacent phases of the 6-phase output.
If you have 3-phase power and you need to step down (or up) in 3-phase voltage, how many single-phase transformers are needed? Explain.
A three-phase transformer bank is connected wye–delta. The primary voltage is 12,470 V, and the secondary voltage is 480 V. The total capacity of the transformer bank is 450 kVA. One of the three transformers that form the three-phase bank develops a shorted primary winding and becomes unusable. A suggestion is made to reconnect the bank for operation as an open-delta. Can the two remaining transformers be connected open-delta? Explain your answer as to why they can or why they cannot be connected as an open-delta. If they can be reconnected open-delta, what would be the output capacity of the two remaining transformers?
For performing dielectric-strength tests on insulating materials, two transformers are connected in a A. parallel combination.B. polyphase arrangement.C. series combination. D. cascade arrangement.