The device serves as a compact torsional spring. It is made of A-36 steel and consists of a solid inner shaft CB which is surrounded by and attached to a tube AB using a rigid ring at B. The ring at A can also be assumed rigid and is fixed from rotating. A torque of T=1.4 kipin. is applied to the shaft. (Figure 1) Figure ▾ Part A 0.5 in. 12 in. 12 in. B 0.75 in. 1 in. Determine the angle of twist at the end C. Express your answer in degrees to three significant figures. 1 of 1

The device serves as a compact torsional spring. It is made of A-36 steel and consists of a solid inner shaft CB which is surrounded by and attached to a tube AB using a rigid ring at B. The ring at A can also be assumed rigid and is fixed from rotating. A torque of T=1.4 kipin. is applied to the shaft. (Figure 1) Figure ▾ Part A 0.5 in. 12 in. 12 in. B 0.75 in. 1 in. Determine the angle of twist at the end C. Express your answer in degrees to three significant figures. 1 of 1

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.8.10P: A bumping post at the end of a track in a railway yard has a spring constant k = 8.0 MN/m (see...

See similar textbooks

Similar questions

Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
A makeshift compact torsional spring is made of steel (Gst = 11,000,000 psi) and is composed of a solid inner shaft from C to B and a hollow shaft from A to B. The solid and hollow shafts are connected through an unyielding ring at B. The necessary radiuses are shown below. Assume the ring attached to the hollow shaft at A is rigid with no rotation. If the torque applied Tat point C is 2 kip-in, find the: a Maximum shear stress in the solid inner shaft, ksi a. Maximum shear stress in the hollow outer shaft, ksi c Angle of twist at point C, degrees 12 in. 12 in. B 0.75 in. T 1 in. 0.6 in.
A makeshift compact torsional spring is made of steel (Gst = 11,000,000 psi) and is composed of a solid inner shaft from C to B and a hollow shaft from A to B. The solid and hollow shafts are connected through an unyielding ring at B. The necessary radiuses are shown below. Assume the ring attached to the hollow shaft at A is rigid with no rotation. If the torque applied T at point C is 2 kip-in, find the: - Maximum shear stress in the solid inner shaft, ksi b. Maximum shear stress in the hollow outer shaft, ksi c Angle of twist at point C, degrees 12 in. 12 in. B 0.75 in. T 1 in. 0.6 in.
A turbine rotor is mounted on a stepped shaft that is fixed at both ends as shown in The torsional stiffnesses of the two segments of the shaft are given by ka = 3,000 N-m/rad and k2 = 4,000 N-m/rad. The turbine generates a harmonic torque given by M(t) = Mo cos wt about the shaft axis with M, = 200 N-m and w = 500 rads. The mass moment of inertia of the rotor about the shaft axis is Jo = 0.05 kg-m. Assuming the equivalent torsional damping constant of the system as c, = 2.5 N-m-s/rad, determine the steady-state response of the rotor, 6(1). O(1) ke M(1) = M, cos ot Turbine rotor, Jo
- A flat spiral steel spring is to give a maximum torque of 1500 N-mm for a maximum stress of 1000 MPa. • Find the thickness and length of the spring to give three complete turns of motion, when the stress . decreases from 1000 to zero. The width of the spring strip is 12 mm. The Young's modulus for the material of the strip is 200 kN/mm2.
A horizontal shaft AD supported in bearings at A and B and carrying pulleys at C and D is totransmit 75 kW at 500 r.p.m. from drive pulley D to off-take pulley C, Calculate the diameter of shaft. The data given is : P1 = 2 P2 (both horizontal), Q1 = 2 Q2 (bothvertical), radius of pulley C = 220 mm, radius of pulley D = 160 mm, allowable shear stress = 45 MPa.[Ans. 100 mm] Given CD=350mm CA=100mm AB=150mm BD=100mm
The shaft shown has two pulleys, where pulley C is the input and pulley A is the output. The shaft is supported by frictionless bearings at points O and B. The pulley diameters are dA = 361 mm and dc = 224 mm. The input tensions on pulley Care T3 = 267 N and T4 = 0.10*T3. The shaft diameter, ds = 25 mm. T₁ da ХОА 1₂ oo ds B dc T3 XAB XBC T₁ • What is the tension T₁ on the output pulley (in N)? Assume the lower tension is 10% of the higher tension.
2. A steel shaft rotating at 600 rpm is supported by two bearings as shown. E=30 Msi, d=1.0" (inch), L₁=24.0" (inches), L=42" (inches), W₁-50 lb, Neglect the weight of the shaft. "The design is acceptable." True ? Show details. or False Diameter d W₁
A typical compound helical spring consists of two coaxial closed coil spring having the following particulars: Outer spring 1: Mean coil diameter = 100mm Wire diameter = 12.5 mm No. of turns = 15 Inner spring 2: Mean coil diameter = 75 mm No. of turns = 20 Both the springs are of equal initial length when unloaded. If the working stress for each spring is to be the same. The modulus of rigidity for the wire material is 80 GPa. Calculate the following: a. Diameter of steel wire for inner spring b. Stiffness of inner spring c. Stiffness of the compound spring
A steel cable is supporting a load of F = 9800 lb and is wrapped around a drum attached to gear A as shown. Assuming the motor is locked in place while the load is applied, answer the following. (1) What is the internal torque in the flexible shaft? (2) What is the rotation of gear A in degrees? 7.0 in bearing gear A 42.0 in gear B bearing 8.0 in -motor solid circular shaft r = 1.2 in G = 2000 ksi L = 38 in
Determine the resisting torque at support A and B , of the shaft shown in the figure.
Consider the compound shaft KC which is composed of a 1200mm long solid rod fitted snuggly into an equally long pipe. Refer to the figure for given dimensions and material properties. If end K is fixed to a rigid wall and a concentrated torque is applied at end C, determine the following: Pipe E = 115 GPa G - 36.0 GPa 1, = 48.0 MPa 1200 mm 180mm Rod E = 220 GPa G = 85.0 GPa *, 80.0 MPa 1. The required outer diameter for the pipe such that the rod and the pipe yields simultaneously. 2. The corresponding maximum angle of twist of the shaft when it yields. 3. The corresponding maximum torque T that can be applied at end C of the shaft