The connection consists of a plate connected to another plate by four 22 mm diameter rivets. It carries a load P = 60 kN at a distance of 344 mm from the centroid of the rivet group. Assume a = 165 mm Determine the shear stress on each rivet due to force alone, in MPa. Determine the shear stress on each rivet due to torsion alone, in MPa. Determine the shear stress on the highly stressed rivet, in MPa

The connection consists of a plate connected to another plate by four 22 mm diameter rivets. It carries a load P = 60 kN at a distance of 344 mm from the centroid of the rivet group. Assume a = 165 mm Determine the shear stress on each rivet due to force alone, in MPa. Determine the shear stress on each rivet due to torsion alone, in MPa. Determine the shear stress on the highly stressed rivet, in MPa

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.5.11P: The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in...

See similar textbooks

Similar questions

A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
A sign is supported by a pipe (see figure) having an outer diameter 110 mm and inner diameter 90 mm. The dimensions of the sign are 2.0 m X 1.0 m, and its lower edge is 3.0 m above the base. Note that the center of gravity of the sign is 1.05 m from the axis of the pipe. The wind pressure against the sign is 1.5 kPa. Determine the maximum in-plane shear stresses due to the wind pressure on the sign at points /I, B, and C, located on the outer surface at the base of the pipe.
A single steel strut AB with a diameter (a) Find the strut force Fs and average normal stress ds= 8 mm supports the vehicle engine hood of a in the strut. mass 20 kg that pivots about hinges at C and D (see (b) Find the average shear stress t aver in the bolt at A,figure parts a and b). The strut is bent into a loop at (C) Find the average bearing stress bon the bolt at A. its end and then attached to a bolt at A with a diameter db= 10 mm. Strut AB lies in a vertical plane.
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
A long re Lai nine: wall is braced by wood shores set at an angle of 30° and supported by concrete thrust blocks, as shown in the first part of the figure. The shores are evenly spaced at 3 m apart. For analysis purposes, the wall and shores are idealized as shown in the second part of the figure. Note that the base of the wall and both ends of the shores are assumed to be pinned. The pressure of the soil against the wall is assumed to be triangularly distributed, and the resultant force acting on a 3-meter length of the walls is F = 190 kN. If each shore has a 150 mm X 150 mm square cross section, what is the compressive stress
Solve the preceding problem if the mass of the tailgate is MT— 11 kg and that of the crate is hic— 6S kg. Use dimensions H = 305 mm, L = 406 mm, dc= 460 mm, and dT= 350 mm. The cable cross-sectional area is At= 11.0 mm'. (a) Find the tensile Force T and normal stress T in each cable. (b) IF each cable elongates
A plane frame with a pin support at A and roller supports at C and £ has a cable attached at E. which runs over Frictionless pulleys al D and B (see figure). The cable force is known to be 400 N. There is a pin connection just Lo the left of joint C. (a) Find reactions at supports^, C, and E. (b) Find internal stress, resultants N, V, and M just to the right of joint C. (c) Find resultant force in the pin near C.
The connection consists of a plate connected to another plate by four 22 mm diameter rivets. It carries a load P = 60 kN at a distance of 165 mm from the centroid of the rivet group. Determine the shear stress on each rivet due to force alone, in MPa. Determine the shear stress on each rivet due to torsion alone, in MPa. Determine the shear stress on the highly stressed rivet, in MPa
Find the tension of the cord that extends from point C to D and compute for stress experienced by the cable if it's diameter in 1.51 in2. Neglect the members weight and friction. Round-off your answer into the nearest whole number. 150 Ivft B 6ft 6 ft E -12 ft 8 ft ANS: T = Ib, Stress = ksi
The vertical load P acting on the wheel of a traveling crane is 13,000 lb. What is the average shear stress in the 1.25 in. diameter axle?
Find the tension of the cord that extends from point C to D and compute for stress experienced by the cable if it's diameter in 1.51 in2. Neglect the members weight and friction. Round-off your answer into the nearest whole number. 150 Ib/ft 6 ft ft 6 ft 12 ft ft ANS: T = Ib, Stress = ksi
As shown, three steel wires, each 28 mm2 in area, are used to lift a mass M. Their unstretched lengths are 19.99 m, 19.98 m, and 20 m. If M= 1,182 kg. what stress exists in the MIDDLE wire? Use E=215 Gpa. Answer must be in MPa.