The channel section shown is of constant thickness t, 16 mm and has an internal height to the top of the flange W of 78 mm The channel is symmetrical about its y axis and has an overall width F, of 185 mm. Determine the position of the neutral axis of the beam measured relative to the position of the base. Number Preesent your answer in mm to 4 sig fig

The channel section shown is of constant thickness t, 16 mm and has an internal height to the top of the flange W of 78 mm The channel is symmetrical about its y axis and has an overall width F, of 185 mm. Determine the position of the neutral axis of the beam measured relative to the position of the base. Number Preesent your answer in mm to 4 sig fig

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter9: Moments And Products Of Inertia Of Areas

Section: Chapter Questions

Problem 9.16P: Figure (a) shows the cross-sectional dimensions for the structural steel section known as C1020...

See similar textbooks

Similar questions

Haw-3 The compressiv Stresf (r)of a rectangular beam sectionis given by the fakmula: 6 M bh where Mis bending moment (24 x1 N-mm Pi axiat ferce (6x1o° N) , b is widthof section (30o mm) and h is height of Section (600 mm),if the errok in measuring (M)is +3-6 x lo° N-mmekkak in measuring (P) ir +18x1 x lo N anderror in measuring each (6) and h) 9 mmyuse khe tatat derivative to find the tatal is
Q1(a) Cross section of a beam is as shown in Figure Q1(a),determine; (i) center of gravity with respect to bottom edge AB; (ii) second moment of area of the section about AB. 200 300 100 A B Figure Q1(a) (take all dimensions in milli meters) (b) If a concentric hole of diameter100 mm drilled on the circular section in Q1(a), explain its effect on the center of gravity with respect to 'AB'.
depth of water on the upstream and downstream sides of the lock are 6 m and 4 m respectively. Find: is 10 m. Each gate is supported by two hinges located at I m and 5 m above the bottom of the lock. The 24. The end gates ABC of a lock are 8 m high and when closed make an angle of 120°. The width of lat gate, and (i) magnitude of the hinge reactions. [Ans. () 79.279 kN, () Ry=27.924 kN, R,= 51.3SAN sides of the gates are 4 m and 3 m respectively, determine : (i) the magnitude of resultant pressure on cat gates are closed, they make an angle of 120°. The width of the lock is 4 m. If the depths of water on the rwe 4m as shown in Fig. 3.60. Consider width of the gate unity. () Resultant water force on cach gate. 21. Find the horizontal and vertical components of the water pressure exerted on a tainter gate of [Ans. F,= 19.62 kN, F, =710244N] 22. Find the magnitude and direction of the resultant water pressure acting on a curved face of a dam which is shaped WATER SURFACE according to the…
Hydraulics In Exercises 41-44, determine the location of the horizontal axis y, at which a vertical gate in a dam is to be hinged so that there is no moment causing rotation under the indicated loading (see figure). The model for y, is Ya Iy hA where y is the y-coordinate of the centroid of the gate, I, is the moment of inertia of the gate about the line y = y, h is the depth of the centroid below the surface, and A is the area of the gate. 44. d y = L y = L y = y Ya=y-hA y
Hwi A beam with I cross-Section is Subjected to negative bending moment M: 50 KN.m.The Cross sectionel dimensions of the beam are shown. Determine the magnitude of marimum bending stress. 15mm loumm 下 le 120 mm
A simply supported beam has a symmetrical rectangular cross-section. If thesecond moment of area (I) of a beam with a rectangular cross-section is 11.50 x 106 mm4 about its centroidal x-axis and the depth dimension (d) of the rectangular section is 180 mm, determine the breadth dimension (b) for this beam section. Give your answer in millimetres (mm) and to 2 decimal places. Assume the beam section material is homogeneous. (show all work)
Maximum Bending Moment: For the beam shown, determine the value of the maximum bending moment at section C due to a uniform live load of 10KN/m, which is 9m long. Round off the answer in KNm, to the nearest whole number. 10KN /m 6m 12m
The simple beam shown supports the uniformly distributed load with intensity Wo = 300 N/m. The span of the beam is 1.2 m. Determine the value of Ely, in N-m³, at midspan. Wo /2 а. -22.7 с. -28.04 b. -26.07 d. Answer is not among the choices TTTT
For the channel-section below a= 40cm b = 10cm a
A beam is subjected to equal 21.7 kip-ft bending moments. Assume t₁ =t₂ = tw- 3 in., d = 15 in., b₁ = 6 in., and b₂ =8 in. The cross- sectional dimensions of the beam are illustrated. Determine: (a) the distance y to the centroid (measured from the bottom), the moment of inertial₂ about the z axis, and the controlling section modulus S₂ about the z axis. (b) the bending stress at point H (positive if tension, negative if compression). (c) the bending stress ok at point K(positive if tension, negative if compression). (d) the maximum bending stress max produced in the cross section (positive if tension, negative if compression). M Answers: (a) y = (b) 6μ = 6.978 (c) OK (c) omax = = i M in., I₂ = X i psi. psi. psi. 41 1₂ 2886.59 b₁ b₂ Cross section H K in.4, S₂ = i in.³.
The cross sectional dimensions of a beam are shown. If the flange thickness, h, is 15.9 mm, determine the vertical distance from the bottom edge of the flange to the centroid of the cross section. Note: State your answer in mm Note: Do NOT include units in your answer. Юнн Answer: 150HM 120 MM hmm
poru i Henuz cevaplanmadı 5,00 uzerinden işaretlenmiş y F Soruyu işaretle H The internal shear force V at a certain section of a beam is 49,9 kN.m. If the beam has a cross-section shown in the figure where h=243 mm, a=99 mm, b=196 mm, c=10 mm and t=12,2 mm, Determine the location of the centroid of the cross-section in the y-axis from the bottom (mm). Yanıt: