The buck converter with resistive load has the input voltage of 30[V], the output voltage of 10 [V](constant), and the switching frequency of 30 [kHz]. If the output average power is 20[W], thendetermine the size of the inductor such that the minimum inductor current is 25 % of the averageinductor current.O 32.78 mikro HenryO 74.07 mikro HenryO 59.26 mikro HenryO 118.52 mikro HenryO 148.15 mikro HenryO 88.89 mikro HenryO 44.44 mikro HenryO 124.56 mikro Henry

From given output power , output voltage and minimum inductor current condition we will find maximum…

Answered: The buck converter with resistive load…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

C'uk Converter Design A C'uk converter has an input of 12 V and is to have an output of - 24 V supplying a 60 W load. Select the duty ratio, the switching frequency, the inductor sizes such that the change in inductor currents is no more than 12 percent of the average inductor current, the output ripple voltage is no more than 1.5 percent, and the ripple voltage across C1 is no more than 3 percent.
Design a Cuk converter that has an input of 25V and the output of -30V. The load is 60W. Specify the duty ratio, switching frequency, inductor values and capacitor values. The maximum change in inductor currents must be 20 percent of the average currents. The ripple voltage across capacitor C1 must be less than 5 percent, and the output ripple voltage must be less than 1 percent.
A Capacitor filter is used at the output across the load to minimize the ripple factor of the output voltage. If R = 20 02 and the single- phase bridge rectifier is supplied from a 120V - 60 Hz sinusoidal source. Find the capacitor value in millifarads that will maintain the amount of the output ripples to less than 5% 艹 Ce = m₂ 0 mF RL%
Q1/ Sketch the output waveform for the circuit. 15V RL Vo -15V Va 7V Input waveform ww
Design a boost converter to provide an output voltage of 36V from a 24V source. The load is 50W. The voltage ripple factor must be less than 0.5%. Specify the duty cycle ratio, switching frequency, inductor and capacitor size, and power device
The buck converter with resistive load has the input voltage of 30[V], the output voltage of 10 [V] (constant), and the switching frequency of 30 [kHz]. If the output average power is 25[W], then determine the size of the inductor such that the minimum inductor current is 25 % of the average inductor current.
design a boost converter to provide an output voltage of 36V from a 24V source. the load is 50W. the voltage ripple factor must be less than 0.5%. specify the duty cycle ratio, switching frequency, inductor an capacitor size
A step down converter is operated with a duty cycle of k 0.75. The input voltage is V, 20V. and the load is L=5mH, R=152 The minimum inductor current is I 0.1A. The maximum inductor current is %3D %3D Select one: O a. 0.9 A O b. 1.9 A O C. None of these O d. 1.1 A O e.2A
Draw the small signal equivalent circuit of the following circuit. Note that C1 and C2 are large AC coupling capacitors. 5 VIO C1 RF Q1 C2 fem RL Vo
Question 4 A boost converter has an input of 5V and an output of 20W at 15V. The minimum inductor current must be no less than 50% of the average. The output voltage ripple must be less than 1%. The switching frequency is 30kHz. Determine the duty ratio, minimum inductor value, and minimum capacitor value. Verify your answers using Matlab, show the inductor current is continues and its minimum is no less than 50% of its average. Furthermore, the output voltage ripple is less than 1%.
O Inductor Diode Voltage Source Switching Device Capacitor This DC-to-DC converter has a duty cycle of 33.3% and an input of 5V. What is the output voltage if the losses are negligible? LOAD
A buck converter operating in continues mode has the following parameters: Imin =0.9 A, Pout 124 W, R=2.6 2, f= 250 Hz, and the average value of the input current = 1.8 A. %3D %3D Find The inductor L in mH.

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS