The bending stress o in a beam depends upon the bending moment Mand the beam area moment of inertia / and is proportional to the beam half-thickness y. For the particular case M= 2900 in-Ibf, y= 1.5 in, and /= 0.4 in4, the predicted stress is 75 MPa. Find the only possible dimensionally homogeneous formula for o. Multiple Choice o = My/2 o = y/MI o = My/l

The bending stress o in a beam depends upon the bending moment Mand the beam area moment of inertia / and is proportional to the beam half-thickness y. For the particular case M= 2900 in-Ibf, y= 1.5 in, and /= 0.4 in4, the predicted stress is 75 MPa. Find the only possible dimensionally homogeneous formula for o. Multiple Choice o = My/2 o = y/MI o = My/l

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Haw-3 The compressiv Stresf (r)of a rectangular beam sectionis given by the fakmula: 6 M bh where Mis bending moment (24 x1 N-mm Pi axiat ferce (6x1o° N) , b is widthof section (30o mm) and h is height of Section (600 mm),if the errok in measuring (M)is +3-6 x lo° N-mmekkak in measuring (P) ir +18x1 x lo N anderror in measuring each (6) and h) 9 mmyuse khe tatat derivative to find the tatal is
The second moment of area of a rectangle is given by the formula I =bh^3/12where b is the breadth and h is the height.Determine the approximate percentage error, if b is measured 3% too largeand the height h is measured 1.7% too small.(Use the Binomial Expansion Method)
Various distributed forces are exerted on the beam shown, w(x) = 2.234 F N/m, p(x) = 1.551 N/m, q(x) = 2.071 N/m, a = 3 m, b = 5 m, and c = 5 m. Determine the net force on them and their direction (+ up. - down). State your answer in kN to 3 significant figures after correct rounding. w (x) a p(x) b q (x)
2 Find the centre of gravity of an inverted T- section with flange 60 mm x 10 mm and web [Ans. 18.6 mm from bottom of the flange] 50 mm x 10 mm 1 A channel section 300 mm x 10 mm is 20 mm thick. Find the centre of gravity of the
20 kN/m 10 kN/m 40 kN 20 kN 20 kN / 10 kN A 2 m 2 m 3 m 2 m, RE 1m RA IF the RA is (42.5) find : Bending moment midway between C and D • Bending moment midway between D and E
Consider the beam in the picture below: 7kN/m 5kN/m P N/m Section 1 Section 2 Section 3 - L/3 L/3 L/3 %3D Take P = the last four digits of your student number in N/m. If P<250 N/m then take P = 30OON/m instead. Take L = the third digit of your student number, reading left to reight. If this value is zero then take L = 2 Assume: The reaction at the Pin = V pin 47000L+9PL )N 54 The reaction at the Roller = Vroller = 61000L+9PL 54 and that both reactions act vertically upwards. a) Find an expression for the internal moment for Section 1. Show all working and any relevant free body diagrams. b) What is the maximum magnitude of the internal moment for Section 1? Mark sure you prove that the value you calculate is the maximum. c) Find an expression for the internal moment for Section 2. Show all working and any relevant free body diagrams. d) What is the maximum magnitude of the internal moment for Section 2? Mark sure you prove that the value you calculate is the maximum. e) Find an…
Find the moment M at O to hold the gate 45° Gate 2 m wide Fig.1 M O Water 700 mm 350 mm 1.3 m PB=-490.8 Pa S-6
3) A point mass is attached to one end of a beam levered against a spike which acts as the pivot. The point mass weighs 250N and the beam has a uniform mass of 10kg and is 8m long. Parts a and b Part c Fapplied 3 of 6mov 1m 8m Krist 0 = 60° Scale 250 N Scale a. If a scale placed beneath the point mass reads 250N, what is the magnitude and direction for the force at the pivot point? Direction: North, 90° from x-axis Magnitude to k* 250N = 2500 N b. For the same scenario, how far must the pivot point be located relative to the left edge of the beam? (Hint, both the boxes weight and the force from the scale act at the farthest right edge of the beam.) www.acta 0672nos onl c. The pivot is then moved to be 6m from the left edge of the beam which now makes a 60 angle with the floor. How much downward force would be needed at the left-most edge of the beam to reduce the reading on the scale to zero? (Hint: the beam is still in static eq. when the scale reads zero.)
The bending moment diagram and cross-section for a beam are shown below. Use the elastic flexural formula ox = -Mzy/l, to determine the required strength of the beam to resist the compressive stresses. Circle the correct answer for the compressive strength in ksi: 2.3, 2.5, 27.5, 30, 37.7 Show your work below. Bending Moment Diagram Beam Cross-Section 4" +50 2' (K-Fe) 2" 2" - 40 2"
1. 2. 10 mm 10 mm 3. 5 mm 100 mm A beam section as shown in the sketch is subjected to a bendingmoment of Mx = 4 kN.m and a shear force of V = 2.5KN. 50 mm 100 mm Calculate the position of the centroid and the the second moment of area of the section about the sentroid horizontally. Draw the bending stress distribution through the height of the beam by calculating the bending stress at the critical positions Draw the shear stress distribution trough the height of the beam by calculating the shear stress below the flanges and at the centroid. 4. Draw the stress condition below the flanges, at the centroid and at the top and bottom of the beam.(7) 5. Draw the shearflow through the section. Show calculations
X B X1 F₂ F2 A X₂ F₁
2. Draw shear force and bending moment diagrams for the beam shown in figure. 50 kN/m 20 kN/m 2 m 2 m - 2 m Ro Hello sir, please the same source as the question solution. 3. Relation between load, shear and moment: The free body diagram wdx :- %3! W (N/m) 严 of segment of this beam of length (dx) is shown M+4M but wdx is the summation of area between (x, and x2) in figure (2). V+av ..V, -V, = AV = (area) nad RI %3! similarly M2 (1) (2) ( dM = Vdx EF, =0= V +wdx-(V+dV)%3D0 w ------- Intensity of load (N/m) . dV =wdx M1 M, - M, = AM = (area ) hm %3! dx M, =0= M+Vdx + (wdx)-(M + dM) =0 shear AP . W =- (dr)? dx (slope of shear diagram) Where: :ero 2 .. dM Vdx dM :.V = dx (slope of moment diagram) for (dV = wdx ) we can integrating