The beam shown is hinged at one end. It is supported by two steel rods of equal length of1.5m. Before the load is applied, the beam hangs level. Use E 200, 000MPa anda = 11.7-m C"Neglect bending of the beam.A=640mm2A=320mm2ACD1.2m0.8 m1.2 m54KNWhat is the stress of rod B if there is no change in temperature in MPa?

Answered: Image /qna-images/answer/0cb1c675-a67d-46c4-9832-d0ec0d91863b.jpg

The beam shown is hinged at one end. It is supported by two steel rods of equal length of 1.5m. Before the load is applied, the beam hangs level. Use E = 200, 000MPa and a=11.7um Neglect bending of the beam. A=640mm2 A=320mm2 A C 1.2 m 0.8 m 1.2 m V 54KN What is the stress of rod B if there is no change in temperature in MPa?

The beam shown is hinged at one end. It is supported by two steel rods of equal length of 1.5m. Before the load is applied, the beam hangs level. Use E = 200, 000MPa and a=11.7um Neglect bending of the beam. A=640mm2 A=320mm2 A C 1.2 m 0.8 m 1.2 m V 54KN What is the stress of rod B if there is no change in temperature in MPa?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the maximum tensile bending stresses in the beam shown. LetP= %3D 19 Note Answer in whole number I = 100 × 106 mm4 P kN/m 2. NA 130 mm 6 m B = 4P 200 mm 2P kN 6-X= Am 4P : - GP
Prob 1. The rigid bar below is supported by a pin and two rods and must support a load of 100 kN is placed 3 m from A. The brass (Ebrass = 85 GPa) rod has a cross section of 30 x 30 mm and the copper (Ecopper = 120 GPa) rod 20 x 20 mm. Determine the normal stress and deflection of both bars. 1.5 m 2 m B -copper 100 kN brass- 3m 3 m E
Q12 (Simple stress and strain) Item 3 of 3 A bar AB (A = 500 mm?) is hinged at A and is supported by a rod CD and C. The rod is pin connected at A, as shown. Neglect deflections of the bar due to bending. If the diameter of the rod connecting the load W = 90 kN is 20 mm, what is the displacement of the load? Use E=210 GPa. (10 38 mm. 2m 1.8m ww Diameter TYOR 2.5 m 1.5m 0.6m W=90kN
Q4) Determine the maximum shear stress acting in the fiberglass beam at the section where the internal shears force is maximum. (tı=15 mm, t2=20 mm, h=150 mm, b=50 mm) 。王! 20 kN/m A |-b-| to 2 m 2 m - 2 m
The rigid bar ABC shown is hinged at A and supported by a steel rod at B. Determine load P that can be applied at C if the stress in the steel rod is limited to 120MPA. E=200 x 10° N/m2 A-300mm? L-3m 3 m 4.5 m
A two pinned end bars AB (Copper), A = 850 mm2, E = 120 GPa and BC (Aluminum), A = 1000mm2, E = 70 GPa is %3D subjected to a horizontal force of 100 kN applied at pin B as shown in the figure, determine the horizontal displacement of pin B. C B 100 kN 2.00m 45° 1.50m
The Figure below shows a two-member truss supporting a block of weight W. The cross-sectional areas of the members are 800 mm² for AB and 400 mm² for AC. Determine the maximum safe value of W (kN) if the working stresses are 110 MPa for AB and 120 MPa for AC. ... B 40 deg. A 60 deg. A) 38.90 в) 55.30 61.70 76.2
The rigid bar AD is supported by two steel wires of 1.5 mm diameter (E = 200 GPa) and a pinand bracket at D. Knowing that the wires were initially taut, determine the stress in each wirewhen a 1200 N load P is applied at D. What is the corresponding deflection of point D?
PROBLEMS 237. The lower ends of the three bars in the figure are at the same level before the rigid homogeneous 18Mg block is attached. Each steel bar has an area of 600mm² and E=200GPa. For the bronze bar, the area is 900mm² and E-83GPa. Find the stress developed in each bar. BRONZE 1.6M STEEL 1M 18Mg STEEL 1M ТЕСНА
A flat steel bar, 25mm wide by 6mm thick and 1 m long, is bent by couple applied at the ends so that the midpoint deflection is 20mm. Use E=200 GN/m^2. Compute: a. the maximum stress in the bar (MPa) b. the magnitude of the couples(N-mm) Round to the nearest whole number.
The shaft is made from a solid steel section AB and a tubular portion made of steel and having a brass core. If it is fixed to a rigid support at A, and a torque of T 50 lb.ft is applied to it at C, determine the rotation angle that occurs at C relative to A and compute the maximum shear stress and maximum shear strain in the brass and steel. Take Gst = 11500 ksi, Gbr 5600 Ksi. %3D %3D 3 ft 2 ft 0.5 in. 1 in. T = 50 lb ft
allowa quired wall thickness 2:11 .l 0.31 KB/S 64 Edit 16 A rigid bar AB is hinged at A and is supported by a rod CD at C. The rod is pin connected at D, as shown. Neglect deflections of the bar due to bending. Use E = 200 GPa. 36 mma 2 m OWhat is the displacement of the loaded end B of the bar? ® Determine the tensile stress induced in rod CD by the 80 kN load D If the allowable stress in rod CD is 124 MPa, what weight W can be safely 1.8 m 12m applied? w80 AN 1. A holl ow cir cular steel colum n is s ubjected toa compression load of 380 kN . The column has a length of 2.4 mn.and an outside dia meter of 187.5 mm. E - 200,000 MPa Determine the min. roquired wall thicknesss base on an allo wable com pressi ve stress of 48 MPa. Determine the min. required wall thickness based on 30 MPa. Determine the min. required wall thickness based on the allowable shortening of the colum n to b e 0.5 0 mm- allowable shear stress of C3D P-38 O kN 2.4 m 2. An 8 mm diameter steel rod, 20 m. long…