Solev the question using matlab The arrangement of cranks in a six-cylinder in-line engine is shown in the figure. The cylinders areseparated by a distance a in the axial direction, and the angular positions of the cranks are given by α₁ =α6 = 0°, α₂ = α5 = 120°, and a3 = α4 = 240°. If the crank length, connecting-rod length, and thereciprocating mass of each cylinder are r, I, and m, respectively, find the primary and secondary unbalancedforces and moments with respect to the reference plane indicated in the figure.2←D→◄D.IT51162,5120°1,6120°120°3, 4

Given the parameters:Number of cylinders, n = 6Angular positions of the cranks = [0, 120, 240, 240,…

The arrangement of cranks in a six-cylinder in-line engine is shown in the figure. The cylinders are separated by a distance a in the axial direction, and the angular positions of the cranks are given by a₁ = α = 0°, α₂ = α5 = 120°, and a3 = a4 = 240°. If the crank length, connecting-rod length, and the reciprocating mass of each cylinder are r, l, and m, respectively, find the primary and secondary unbalanced forces and moments with respect to the reference plane indicated in the figure.

The arrangement of cranks in a six-cylinder in-line engine is shown in the figure. The cylinders are separated by a distance a in the axial direction, and the angular positions of the cranks are given by a₁ = α = 0°, α₂ = α5 = 120°, and a3 = a4 = 240°. If the crank length, connecting-rod length, and the reciprocating mass of each cylinder are r, l, and m, respectively, find the primary and secondary unbalanced forces and moments with respect to the reference plane indicated in the figure.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An inside cylinder locomotive has its cylinder centre lines 1 m apart and has a stroke of 1 m. The rotating masses per cylinder are equivalent to 100 kg at the crank pin, and the reciprocating masses per cylinder to 200 kg. The wheel centre lines are 2 m apart. The cranks are at right angles. The whole of the rotating and 2/3 of the reciprocating masses are to be balanced by masses placed at a radius of 0.8 m. Find the magnitude of the balancing mass on the right most wheel. Select one: A. 55.32 kg B. 322.3 kg C. 225.3 kg D. 115.3 kg
Problem Graphically position the links for the compressor linkage in the configuration shown in Figure. Then reposition the links as the 45-mm crank is rotated 90° counterclockwise. Determine the resulting displacement of the piston. FIGURE 45 mm 100 mm piston 30 crank
The crank-rocker mechanism shown has lengths n = 9 in, r2 = 2 in, r3 = 7 in, andr4= 10 in. Find the angular displacement Aa that crank OA makes to move the rocker OpB from the extreme right to the extreme left position. Crank OAA rotates counterclockwise as shown. Write your answer in degrees but do not write the units. B A 0B Answer. DELL
8. The torque exerted on the crank shaft of a two stroke engine is given by the equation: T(N-m)= = 14 500 + 2300 sin 20 – 1900 cos 20 where 0 is the crank angle displacement from the inner dead centre. Assuming the resisting torque to be constant, determine: 1. The power of the engine when the speed is 150 r.p.m. ; 2. The moment of inertia of the flywheel if the speed variation is not to exceed ± 0.5% of the mean speed; and 3. The angular acceleration of the flywheel when the crank has turned through 30° from the inner dead [Ans. 228 kW; 1208 kg-m²; 0.86 rad/s²] centre.
Unlike the common V6 engine, Subaru engines contain pistons that are horizontally opposed (see Wikipedia for more info). Luckily for us, this also makes for an interesting dynamics problem! At the instant shown, the crank arm's angular velocity is waB = 2,000 rpm (rotating clockwise) and the angle 0 = 40° with respect to the horizontal. Length of bar AB is r1 = 3 in. and the length of bar BD is r2 = 8 in. a) Clearly define coordinate systems for each link and write transformation arrays for each. b) Compute the velocity of point B in ft/s. Express your answer in rectangular coordinates. [Ans. to Check: 33.66 i– 40.11 j ft/sec] c) Determine the magnitude of the speed of the piston P in ft/s. Note: all answers should be positive since we only want to know the magnitude of the speed, not the direction (the piston can only move in the horizontal direction). [Ans. to Check: 43.6 ft/s] r2 10 B
Question 1 An inside cylinder locomotive has its cylinder centre lines 1 m apart and has a stroke of 1 m. The rotating masses per cylinder are equivalent to 100 kg at the crank pin, and the reciprocating masses per cylinder to 200 kg. The wheel centre lines are 2 m apart. The cranks are at right angles. The whole of the rotating and 2/3 of the reciprocating masses are to be balanced by masses placed at a radius of 0.8 m. Find the magnitude of the balancing mass on the right most wheel. Select one: A. 55.32 kg B. 322.3 kg C. 225.3 kg D. 115.3 kg Question 2 For the data given in Question 1, find the direction (with horizontal) of the balancing mass on the left most wheel. Select one: A. 115 degrees B. 15 degrees C. 215 degrees D. 45 degrees
A shaft carries four masses A, B, C and D with a a magnitude of 200kg, 300kg, 400 kg and 200 kg respectively and revolving at radii 80mm, 70mm, 60mm and 80mm in planes measured from A at 300mm, 400mm and 700mm. The angles between the cranks measured counter clockwise are A to B 450, B to C 700 and C o D 1200. The balancing masses are to be placed in planes X and Y. Distance between planes A and X is 100mm, between X and Y is 400mm and between Y and D is 200mm. If the balancing masses revolve at radius of 100mm find their magnitude and angular position
The figure below depicts a camshaft assembly such as one that might be found in an automobile engine to open and close intake and exhaust valves. The cam is a circular disk of radius R with a hole of diameter R cut through it. As shown in the figure, the hole does not pass through the center of the disk. The cam with the hole cut out has mass M. The cam is mounted on a uniform, solid, cylindrical shaft of diameter R and also of mass M. What is the kinetic energy of the entire camshaft assembly when it is rotating with angular speed ? about the shaft's axis? (Use any variable or symbol stated above as necessary.)
The figure below depicts a camshaft assembly such as one that might be found in an automobile engine to open and close intake and exhaust valves. The cam is a circular disk of radius R with a hole of diameter R cut through it. As shown in the figure, the hole does not pass through the center of the disk. The cam with the hole cut out has mass M. The cam is mounted on a uniform, solid, cylindrical shaft of diameter R and also of mass M. What is the kinetic energy of the entire camshaft assembly when it is rotating with angular speed ω about the shaft's axis? (Use any variable or symbol stated above as necessary.)
In the mechanism shown below, points E and B have the same vertical coordinate. Find the velocities of points B. C, and D of the double-slider mechanism shown in the figure if Crank 2 rotates at 42 rad/s CCW. And all forces acting. D 6. EA - 0.55" AB - 2.5" AC - 1.0" CB = 1.75" CD - 2.05" 0.75"- 4 3 60 A
In the image on the right, there is a red gear G1 on the left with a radius of r1 = 2.81cm. Gear G1 is locked to the green gear G2 with a radius of r2 = 0.734cm. Gear G2 then shares the same axle as the blue circular saw G3, which has a radius of r3 known to make a full rotation every T = 0.836s. Using at least 6 significant digits in your calculations, compute the following: V3! 12.8cm. Gear G1 is W1 a) The angular speed wi of gear G1. Remember that angular speed is measured in radians per T3 r2 unit time. G2 b) The rim speed vi of gear G1. Since gears G1 and G2 are locked together, the rim speed of G2 is also v1. G1 G3 c) The angular speed w2 of gear G2. Since gear G2 and saw G3 share the same axle, the angular speed of G3 is also w2. d) The rim speed v3 of saw G3.
Analytically determine the linear displacement of the piston in the compressor linkage shown in the figure as the 45 mm. crank is rotated from its current position 90 degree clockwise.