SOLVE CAREFULLY!! Please Write Clearly and Box the final Answer Suppose an analysis has revealed that the candidate trouble spot in a part is a state of plane stress with ox equal to 15 ksi, oy equal to 1 ksi, and Txy equal to 10ksi. Furthermore, the yield strength is Sy equal to 76 ksi. The safety factor by the Distortion Energy theory is

Answered: Image /qna-images/answer/e2e29830-cfa0-4e9b-a49b-e4613a6a7c48.jpg

Answered: Suppose an analysis has revealed that…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q6/ A material has a true stress -strain curve given by o=Kɛ", derive and calculate the true and engineering ultimate tensile strength of this material. (use : k=689.47kpa , n=0.5)
! Required information A ductile hot-rolled steel bar has a minimum yield strength in tension and compression of 350 MPa. Using the distortion-energy and maximum-shear-stress theories, determine the factors of safety for the following plane stress states. 0x = 96 MPa, and Txy = -76 MPa The factor of safety from the maximum-shear-stress theory is " and the factor of safety from the distortion-energy theory is
A machine part is made of forged steel with Sy = 630 MPa, S'== 0.5 S, .Estimate the life cycles (L) for a fatigue strength of 294 MPa. For 103 cycles, take Sf=0.9 S,
Problem 2: Determine the Factor of Safety for the following condition: (a) Using distortion-energy theory, determine the factor of safety of a AISI 1040 hot-rolled steel for the following plane stress states: o = -50 MPa, o, = 40 MPa, Ty=-80 MPa (b) Using Coulomb-Mohr and Modified mohr theory, determine the factor of safety of a ASTM 50 cast iron for the following principal stress states: o, = 10 kpsi, o, = -15 kpsi, ty= -20 kpsi
Determine the factor of safety for fatigue at million cycles (2 decimal places) if a steel part experiences Omax 95 MPa, Omin -30 MPa, Tmax 50 MPa, and Tmin -5 MPa. Sut = 435 MPa and Se 125 MPa. Your Answer:
B) A machine part is made of forged steel with Su = 630 MPa, S'e = 0.5 Su. Estimate the life cycles (L) for a fatigue strength of 294 MPa. For 103 cycles, take S, = 0.9 Su. %3D
A rod specimen of ductile cast iron was tested in a torsion-testing machine. The rod diameter was 16 mm, and the rod length was 360 mm. When the applied torque reached 254.8 N-m, a shear strain of 1780 microradians was measured in the specimen. What was the angle of twist in the specimen? Part 1 Calculate the shear stress in the specimen. Correct Answer: T= 316.97 eTextbook and Media Part 2 Correct Use Hooke's Law to calculate the shear modulus of the specimen. answer: G= 178073.034 Part 3 eTextbook and Media Incorrect MPa Answer: Calculate the angle of twist in the specimen. D=0.8006 MPa O Attempts: 1 of 5 used Attempts: 1 of 5 used
Required information A ductile hot-rolled steel bar has a minimum yield strength in tension and compression of 350 MPa. Using the distortion- energy and maximum-shear-stress theories, determine the factors of safety for the following plane stress states. 0x = -46 MPa, Oy = -80.5 MPa, and Txy = -46 MPa The factor of safety from the maximum-shear-stress theory is 3.56, and the factor of safety from the distortion-energy theory is 3.3
A rod specimen of ductile cast iron was tested in a torsion-testing machine. The rod diameter was 16 mm, and the rod length was 360 mm. When the applied torque reached 254.8 N-m, a shear strain of 1780 microradians was measured in the specimen. What was the angle of twist in the specimen? Part 1 Calculate the shear stress in the specimen. Correct Answer: T= 316.97 eTextbook and Media Part 2 Use Hooke's Law to calculate the shear modulus of the specimen. answer: G= i MPa MPa Attempts: 1 of 5 used
(a) determine the minimum factor of safety based on yielding according to the maximum- shear-stress theory. (b) determine the minimum factor of safety based on yielding according to the distortion-energy theory.
A small element at the critical section of a component is in bi-axial state of stress with two principal stresses being 360 MPa and 140 MPa. The maximum working stress according to distortion energy theory (in MPa) is
Q4- Explain the following state "other mechanical properties often may be estimated from hardness data" Q5- "Engineering stress-stain curve and True stress-strain curve are similar". Why? Q6- Is it possible utilized bending test for non-brittle materials? Why? Q7- Engineering stress-strain curve for the compression test is similar to that of the tensile test. But the shape of plastic region is different. Explain why? Q8- find the yield point for brittle and ductile materials?

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

Suppose an analysis has revealed that the candidate trouble spot in a part is a state of plane stress with ox equal to 15 ksi, oy equal to 1 ksi, and Txy equal to 10 ksi. Furthermore, the yield strength is Sy equal to 76 ksi. The safety factor by the Distortion Energy theory is