Steel Bronze Area (mm) 600 300 3. Figure (a) shows a rigid bar that is supported by a pin at A and two rods, one made of steel and the other of bronze. Neglecting the weight of the bar, compute the stress in each rod caused by the 50- kN load, the following data : E (GPa) 200 83 Bronze Steel 2 m 1.0 m 1.0 m 0.8 m 50 kN (a)

Steel Bronze Area (mm) 600 300 3. Figure (a) shows a rigid bar that is supported by a pin at A and two rods, one made of steel and the other of bronze. Neglecting the weight of the bar, compute the stress in each rod caused by the 50- kN load, the following data : E (GPa) 200 83 Bronze Steel 2 m 1.0 m 1.0 m 0.8 m 50 kN (a)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An aluminum rod is rigidly attached between a steel rod and a bronze as shown. Axial loads are applied at the positions indicated. Find the stress of each rod in MPa. Steel Aluminum Bronze A- 500mm A = 400mm? A- 200mm 40KN 10KN 20KN 1.5m 2.5m 2.0m Determine the change in length of steel rod having a length of 800mm and a diameter of 6.5mm. The rod is subjected to a force P equal to 110KN. Young's Modulus is 200GPA Compute normal strain of the rod
PROBLEMS: 1. The bolt connection shows 8-22mm diameter bolts in a bolt hole diameter of 25 mm and spaced according to the following: Sı = 40mm T = 16mm S2 = 80mm S3 = 50mm S4 = 100mm te = 12mm Determine the force T if the allowable tensile stress is 200 MPa, the allowable bolt shear stress is 120MPa and the allowable plate bearing stress is 120 MPa. 2. A long retaining wall is braced by wood shores set at ang angle of 30° and supported by concrete thrust blocks as shown. The shores are evenly spaced, 3m apart. For analysis purposes, the wall and shores are idealized on the second image. Note that the base of the wall and both ends of the shores are assumed to be pinned. The pressure of the soil against the wall I assumed to be triangularly distributed, and the resultant force acting on a 3-meter length of the wall is F= 190KN. If each shore has a 150mmx150mm square cross section, what is the compressive stress in the shores? Retaining wall Soil Concrete Shore thrust block 30 30 1,5 m…
A cast iron beam is of I-section as shown in figure below. The beam is simply supported on a Span of 5 meters. If tensil Stress is not execed 20 N/mm², find the safe uniformly load which the beam can carry. find also the maximum Compressive Stress. 25mm k120mm. 300mm T 50mm ↓ B 25mm ← 240- 키
Q4) A cast iron beam is of I – section as shown in Figure (3). The beam is simply supported on a span of 5 m. If the tensile stress is not to exceed 20 N/mm2, find the safe uniformly load which the beam can carry. Find also the maximum compressive stress. I 80 mm- 20 mm 3 169.34 mm 200 mm 2) 20 mm A 90.66 mm 40 mm 100 mm Figure (3)
The figure below shows a shaft of three segments. It is restrained (fixed support) at both sices and is loaded by two torques. Use Groze -35 GPa, Glum - 28 GPa, and Getee - 83 GPa Aluminum Steel Bronze digmeter = 50 mm diameter = 25 mm diameter = 25 mm T-300 N.m K To =700 N.m4K 2 m 2 m 2.5 m Determine the maximum shearıng stress developed in aluminum. Select the corect response 214.16 MPa 175 MPa 57.12 MPa 111.79 MPa
The rigid bar of negligible weight is supported as shown. The assembly is initially stress-free. Find the stress in each rod if the temperature rises after a load W = 120 kN is applied. Steel rod Bronze rod A (mm²) 350 1500 a (/°C) 11.7 x 10-6 18.9 x 10-6 E (GPa) 200 83 Steel 1.5 m 1.0 m O 2.5 m. 10. Determine the stress at the bronze rod in MPa when there is a temperature rise of AT = 30 °C. W Bronze 3 m 1.5 m-
a. Calculate "P" in KN considering tension failure on gross area Two A36 16mm Thick Steel Plates Are Connected By Four Rivets With Fv=152 MPa As Shown. Given: Rivet Dia 20 mm x=100 mm
A flanged bolt coupling consist of 9 steel bolts evenly spaced around a bolt circle 300 mm. in diameter and 6 bronze bolts on a concentric bplt circle 200 mm. in diameter. What are the sizes of bolts diameters for steel and bronze, if the torque applied is 6,000 N-m and without exceeding the stress of 60 MPa in the steel and 40 MPa for the bronze? The ratio of the bolt diameter db / ds = 0.50. For steel, use Gs = 83 GPa and for bronze, Gb = 28 Gpa.
The rigid bar AB, attached to two vertical rods as shown in Fig. is horizontalbefore the load P is applied. Determine the maximum value for P If the stress must not exceed: 160 MPa for steel and 80 MPa for Bronze. Then determine the vertical movement of P. STEEL Lm A-400 mm E-200 GPa BRONZE L-5m A-500 mm E-80 GPa 3m
The rigid bar of negligible weight is supported as shown. The assembly is initially stress-free. Find the stress in each rod if the temperature rises after a load W = 120 kN is applied. Steel rod Bronze rod A (mm²) 350 1500 a (/°C) 11.7 x 10-6 18.9 x 10-6 E (GPa) 200 83 O Steel 1.5 m 1.0 m- 2.5 m 9. Determine the stress at the steel rod in MPa when there is a temperature rise of AT = 36 °C. W Bronze 3 m 1.5 m-
Determine the load that can be applied at the end of the rigid bar if the stress in either spring shown in the figure shall not exceed 200MPA. Spring 1 20 Spring 2 n 30 d 10mm 20mm D 150mm 120mm G 83GPA 35GPA 2m www
1/2 Problem 1: Two solid cylindrical rods AB and BC are welded together at B and loaded as shown in. If the stress must not exceed 14OMPA in either rod, determine the smallest allowable value of the diameter of rod AB and ВС. 300mm B 40 kN 250mm - d2 30 kN