Steady state temperatures at three nodes are given in K. This object generates heat itself at rate of q = 5×107 W/m³ and has a thermal conductivity of 20 W/m K. Two of its sides are maintained at a constant temperature of 300 K, while the others are insulated. Find temperatures at nodes 1, 2 and 3 in K. 5 mm 2 398.0 348.5 3 374.6 - Uniform temperature, 300 K 5 mm
Q: Explain the concept of entropy and its significance in the second law of thermodynamics. Discuss how…
A: The solution is provided below.
Q: The diameter of a 3/4-10 American Standard thread is to be checked by the three-wire method.…
A: Here is the solution of your question:-Explanation:The three-wire method is commonly used to measure…
Q: A syringe, containing an incompressible fluid, is oriented vertically and the plunger is slowly…
A: Given:At the maximum height point , velocity is zero.Hence, Assume the diameter at point is D and…
Q: The floor of a railroad flatcar is loaded with loose crates having a coefficient of static friction…
A:
Q: Free Body Diagram Problems Problem 1 Draw a proper free body diagram for the curved bar shown below.…
A: Free Body Diagram : Let a body is in contact with some other body or have any type of support, Now…
Q: diatomic gas follows the cycle shown in the figu
A:
Q: How much work is done (by a battery, generator, or some other source of potential difference) in…
A: The work done is 1.14 x 106 JExplanation:Approach to solving the question: Detailed explanation:…
Q: Which of the following is true for the strain gauge alight H R1 R3 Both temperature and axially…
A: Strain gauge alignment refers to the proper orientation and positioning of strain gauges on a…
Q: 7. A guy wire from a smoke stack is 120 feet long. How high is the stack if the wire is attached 10…
A: h≈75.36 ftExplanation:Let us draw the figure,The 120' guy wire is attached 10' from the top of the…
Q: The forked rod is used to move the smooth 3 lb particle around the horizontal path in the shape of a…
A:
Q: Consider a pulley system shown below. The coordinate y is the displacement of center of mass of the…
A:
Q: or the velocity field: u = 3xy, v = -1.5y²+5; for water, ρ = 1000 kg/m³ If the pressure at (0,0) is…
A: The velocity field is .The density of water is .The pressure at is .
Q: Explain the results of the assessment using the time graph and at least three of the measurements…
A: Based on the provided time graph and the measurements collected, we can assess the results as…
Q: Water is discharging through a circular orifice plate 25mm in diameter in the vertical side of the…
A: See an attachment for the solution. Explanation:
Q: A latch is made from steel with 490 Bhn, a machined finish, and a yield strength of 100 ksi. Assume…
A:
Q: slotted link. If x=2 m/s and x = 15 m/s² when x = 1 m, find the acceleration of A with respect to…
A:
Q: Water is the working fluid in a regenerative Rankine cycle with one open feedwater heater. Steam…
A: The inlet condition of steam at 1st stage turbine is The feed water pressure is The exit pressure of…
Q: Determine the Grashof condition and Barker Classification for the following mechanism, if d = 0.1 m,…
A: The solution is provided below.Here P and Q are the rest two link other than the shortest and…
Q: III-A component is subjected to a cyclic loading at the frequency of once every 5 minutes for 5…
A:
Q: • Lengths: O2A-4 in., O3B=8 in, BC=5 in, O2O3-4 in. and offset c=10 in. • Angles: 8-60° and = 45°…
A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…
Q: Two point charges are on the y axis. A 4.90-µC charge is located at y = 1.25 cm, and a -2.04-µC…
A: Detailed solution of the problem is attached below.Explanation: Detailed explanation:
Q: SITUATION 1: As shown in the figure, a weight W = 50 kN hangs from two wires. Given that θ = 30° and…
A:
Q: A 9 kg box moves at constant speed on a plane inclined at 29° Due to a force pulling up the plane,…
A: Given data:The mass of the box The coefficient of friction Determine:The magnitude of the force
Q: O Consider a single-degree-of-freedom overdamped system, which is harmonically excited by a forcing…
A:
Q: Which moment(s) will produce bending stress at H? Select all that apply. y My HK Mx M Mx My Mz x
A: Only M_x will produce a compressive Bending stress at HExplanation:M_x will produce a Compressive…
Q: Three cables are used to tether a balloon as shown in the figure. Knowing that the balloon exerts a…
A: Three cables are used to tether a balloon as shown in the figure. Knowing that the balloon exerts a…
Q: Design and draw a channel jig for mild steel components, as in figure below, to drill a hole of 18…
A: To design and draw the channel jig for mild steel components
Q: The energy flux associated with solar radiation incident on the outer surface of the earth's…
A:
Q: The car passes point A with a speed of 25 m/s after which its speed is defined by v = (25 - 0.15 s)…
A:
Q: 4.44 Consider the 2-degree-of-freedom system defined by: [2]+[233] x=0 3¾ X= Use modal analysis to…
A: The equation of 2 degree of freedom is defined by The initial condition are
Q: 1. Write the equations of incompressible elasticity in unabridged notation. 2. Write the Stokes…
A: To find: The equations of incompressible elasticity in unabridged notation. The Stokes equations in…
Q: 4) Consider the system below. Write the equation of motion and calculate the response assuming that…
A: Given data:
Q: A BMW vehicle consumes 2.5 gallons of gasoline in 60 minutes while operating at3000 RPM. Calculate…
A: Given:The BMW vehicle consumes gallons of gasoline in minutes.Each gallon of gasoline contains of…
Q: Parvinbhai
A: The objective of the question is to determine the displacement at point B of a loaded beam ABC,…
Q: This is not a quiz question. It is part of a review packet. Free Body Diagram and Kinetic Free…
A: So, the results obtained by direct application of Newton's Second Law are consistent with the…
Q: For the mechanism shown below, the hydraulic cylinder DB extends with a constant velocity of vg =…
A: The velocity of point B is
Q: 7. Find the distance a person can be from the wall and still be in equilibrium. Hanging mass = 21 kg…
A:
Q: A cylindrical 4135 cold-rolled steel workpiece has an upsetting load applied at room temperature…
A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…
Q: A pipe is buried underground during summer 20°C. Winter kicks in suddenly, and air at Too the ground…
A:
Q: PROBLEM 4: The boom OC is subjected to tension forces at A and C. It is known that the tension in A…
A: Given:To Find:Unit vector CE. Tension at A in vector formsMoment about O due to the given forces
Q: Make a summary about the welding procedures (properties, scratches, weld quality, appropriate place…
A: The objective of this question is to provide a comprehensive summary of welding procedures,…
Q: 4. The top of a male dovetail is 4 inches wide. If the angle is 55° and the depth is 5/8 inch, what…
A: 4.88''Explanation:Let's illustrate the problem,Given the width of the top of male dovetail which is…
Q: Required information A 920-mm (4) strip of steel (E= 200 GPa) is bent into a full circle by two…
A: Maximum thickness of the strip is 0.615 mmExplanation:
Q: Assume the following objects are pushed with a force such that they all accelerate at the same rate…
A: The objective of the question is to determine which object among a cricket ball, hockey puck, soccer…
Q: This is not a quiz question. It is part of a review packet. Free Body Diagram and Kinetic Free…
A: Answer - The additional deflection of the springs is δ = 2.549(in)Explanation:Step 1:The weight of a…
Q: For some metal alloy, a true stress of 345 MPa (50040 psi) produces a plastic true strain of 0.02.…
A: The step by step solution for this problem is shown below.
Q: (a) If the shaft is subjected to an external torque T at point b, find the angle of twist of point b…
A: To determine the angle of twist, when the external torque at position 'a' and 'b'given the common…
Q: Water pressure in the supply system exerts a downward force of 30 lb on the vertical plug at A.…
A: The downward force at vertical plug A is .
Q: A beam ABC is supported by both a uniformly distributed load and a concentrated load as indicated…
A: Bearing reactions of beam are RA= 11.5 KN RB= 46.5 KN Maximum bending moment in beam = 11.02…
Q: The pump has an er diameter of 8 cr 1750
A: The outer diameter of the pump is .The inner diameter of the pump is .The width of the blade is .The…
Trending now
This is a popular solution!
Step by step
Solved in 1 steps with 2 images
- A plane wall 15 cm thick has a thermal conductivity given by the relation k=2.0+0.0005T[W/mK] where T is in kelvin. If one surface of this wall is maintained at 150C and the other at 50C, determine the rate of heat transfer per square meter. Sketch the temperature distribution through the wall.2.15 Suppose that a pipe carrying a hot fluid with an external temperature of and outer radius is to be insulated with an insulation material of thermal conductivity k and outer radius . Show that if the convection heat transfer coefficient on the outside of the insulation is and the environmental temperature is , the addition of insulation actually increases the rate of heat loss if , and the maximum heat loss occurs when . This radius, is often called the critical radius.To determine the thermal conductivity of a structural material, a large 15-cm-thick slab of the material is subjected to a uniform heat flux of 2500 W/m2 while thermocouples embedded in the wall at 2.5 cm. intervals are read over a period of time. After the system had reached equilibrium, an operator recorded the thermocouple readings shown below for two different environmental conditions: Distance from the Surface (cm) Temperature (C) Test 1 0 40 5 65 10 97 15 132 Test 2 0 95 5 130 10 168 15 208 From these data, determine an approximate expression for the thermal conductivity as a function of temperature between 40 and 208C.
- 1.63 Liquid oxygen (LOX) for the space shuttle is stored at 90 K prior to launch in a spherical container 4 m in diameter. To reduce the loss of oxygen, the sphere is insulated with superinsulation developed at the U.S. National Institute of Standards and Technology's Cryogenic Division; the superinsulation has an effective thermal conductivity of 0.00012 W/m K. If the outside temperature is on the average and the LOX has a heat of vaporization of 213 J/g, calculate the thickness of insulation required to keep the LOX evaporation rate below 200 g/h.A plane wall of thickness 2L has internal heat sources whose strength varies according to qG=qocos(ax) Where qo is the heat generated per unit volume at the center of the wall (x=0) and a is a constant. If both sides of the wall are maintained at a constant temperature of Tw, derive an expression for the total heat loss from the wall per unit surface area.1.3 A furnace wall is to be constructed of brick having standard dimensions of Two kinds of material are available. One has a maximum usable temperature of 1040°C and a thermal conductivity of 1.7 W/(m K), and the other has a maximum temperature limit of 870°C and a thermal conductivity of 0.85 W/(m K). The bricks have the same cost and are laid in any manner, but we wish to design the most economical wall for a furnace with a temperature of 1040°C on the hot side and 200°C on the cold side. If the maximum amount of heat transfer permissible is 950 , determine the most economical arrangement using the available bricks.
- 1.77 Explain each in your own words. (a) What is the mode of heat transfer through a large steel plate that has its surfaces at specified temperatures? (b) What are the modes when the temperature on one surface of the steel plate is not specified, but the surface is exposed to a fluid at a specified temperature?2.30 An electrical heater capable of generating 10,000 W is to be designed. The heating element is to be a stainless steel wire having an electrical resistivity of ohm-centimeter. The operating temperature of the stainless steel is to be no more than 1260°C. The heat transfer coefficient at the outer surface is expected to be no less than in a medium whose maximum temperature is 93°C. A transformer capable of delivering current at 9 and 12 V is available. Determine a suitable size for the wire, the current required, and discuss what effect a reduction in the heat transfer coefficient would have. (Hint: Demonstrate first that the temperature drop between the center and the surface of the wire is independent of the wire diameter, and determine its value.)The heat flow per unit length of a thick cylindrical pipe is 772 W per meter. The pipe has radii ri = 12 cm, ro = 24 cm, outside surface temperature, To = 95 deg C and k = 0.05 + 0.0008T where T is in deg C and k is in W/(m K). Find the inside surface temperature of the pipe, assuming steady state conditions and accounting for the variation of thermal conductivity with temperature. Also determine the temperature of a point midway to the inside and outside radius.
- Find the two-dimensional temperature distribution T(x,y) and midplane temperature T(B/2,W/2) under steady state condition. The density, conductivity and specific heat of the material are p=(1200*32)kg/mº, k=400 W/m.K, and cp=2500 J/kg.K, respectively. A uniform heat flux 9" =1000 W/m² is applied to the upper surface. The right and left surfaces are also kept at 0°C. Bottom surface is insulated. 9" (W/m) T=0°C T=0°C W=(10*32)cm B=(30*32)cmThe initial temperature distribution of a 5 cm long stick is given by the following function. The circumference of the rod in question is completely insulated, but both ends are kept at a temperature of 0 °C. Obtain the heat conduction along the rod as a function of time and position ? (x = 1.752 cm²/s for the bar in question) 100 A) T(x1) = 1 Sin ().e(-1,752 (³¹)+(sin().e (-1,752 (²) ₁ + 1 3π TC3 .....) 100 t + ··· ....... 13) T(x,t) = 200 Sin ().e(-1,752 (²t) + (sin (3). e (-1,752 (7) ²) t B) 3/3 t + …............) C) T(x.t) = 200 Sin ().e(-1,752 (²t) (sin().e(-1,752 (7) ²) t – D) T(x,t) = 200 Sin ().e(-1,752 (²)-(sin().e (-1,752 (²7) ²) t E) T(x.t)=(Sin().e(-1,752 (²t)-(sin().e(-1,752 (²) t+ t + ··· .........) t +.... t + ··· .........) …..)Drive an expression for heat transfer and temperature distribution for steady state one dimensional heat conduction in a plan wall. The temperature is maintained at a temperature Ti at x=0, while the other face X-L is maintained at temperature T2, the thickness of the wall may be taken as L and the energy equation is given by: d²T/dx² = 0. : Sketch a simple diagram for the temperature distribution in plane wall for a steady state one dimensional heat conduction, with heat generation. The surface temperature of the walls Ti and T2, for the cases Ti>T2, T1-T2, and T2>T1. The thickness of the wall may be taken as 2L