Steady state handling diagrams are a useful tool to analyse the cornering behaviour of a vehicle. a) Draw a steady state handling diagram for a car which understeers for low lateral acceleration but oversteers for high lateral acceleration. b) On your diagram, indicate where the vehicle behaviour changes from understeer to oversteer and explain possible reasons for this behaviour. c) Comment on the car's stability at the limit of its cornering capabilities and how the driver would have to operate to control the car's behaviour at this limit.

Steady state handling diagrams are a useful tool to analyse the cornering behaviour of a vehicle. a) Draw a steady state handling diagram for a car which understeers for low lateral acceleration but oversteers for high lateral acceleration. b) On your diagram, indicate where the vehicle behaviour changes from understeer to oversteer and explain possible reasons for this behaviour. c) Comment on the car's stability at the limit of its cornering capabilities and how the driver would have to operate to control the car's behaviour at this limit.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Which of the following can be used to building up a three-dimensional prototype model layer by layer from CAD data? O a. All of the above O b. Stereolithography 0 с. Laminated object manufacturing O d. Selective laser sintering
Match 4 correct pairs between List-l and List-ll for questions. No credit will be given for partially correct matching. List-l A. Collision of particles B. Stability C. Satellite motion D. Spinning top List-ll 1. Euler's equation of motion 2. Minimum kinetic energy 3. Minimum potential energy 4. Impulse momentum principle 5. Conservation of moment of momentum
C Dynamic Analysis and Aeroelasticity SECTION B Answer TWO questions from this section ENG2012-N The moment of inertia of a helicopter's rotor is 320kg. m². The rotor starts from rest and at t = 0, the pilot begins by advancing the throttle so that the torque exerted on the rotor by the engine (in N.m) is modelled by as a function of time (in seconds) by T = 250t. a) How long does it take the rotor to turn ten revolutions? b) What is the rotor's angular velocity (in RPM) when it has turned ten revolutions?
(2) lahai Q1-e) Kinetics: is used to predict the motion caused by given forces or to determine the forces required to produce given motion True False
Write down the five requirements of your cars autonomous project in good specification way?
A completely automated Tesla travels up a 3% incline at 30 mph on a road that has good, wet pavement. The car has a wheelbase of 120 inches and a center of gravity that is 55 inches behind the front axle and at a height of 20 inches. The braking efficiency is 88%. It notices a pothole 35 ft ahead of the car and comes to a complete stop. a) Calculate the percentages of braking force that should be allocated to the front and rear brakes to ensure that maximum braking forces are developed. b) Will the car hit the pothole if it has (i) no antilock brakes and (ii) antilock brakes (braking efficiency 100%)? Assume theoretical stopping distance and neglect aerodynamic resistance.
‘The following particulars refer to a two-row velocity-compounded impulse wheel which forms the frst stage of a combination turb Steam velocity at nozzle outlet 1630 mis Mean blade velocity 1125 mls Nozzle angle 116° Outlet angle, first row of moving blades 18 Outlet angle, fixed guide blades 22 Outlet angle, second row of moving blades :36° Steam flow rate 26kg's ‘The ratio of the relative velocity at outlet to that at inlet is 0.84 for all the blade. Determine (a) The velocity of whirl.
After some engine model replacement, an aircraft model is experiencing some aggressive nose up phenomenon which may lead to stall. To combat this problem, a new control system has been introduced to the Flight Control Computer, FCC. When activated, the new system measure the aircraft pitch from an Angle of Attack, AOA sensor to analyze either the aircraft is nosing up or down. If the pitch angle is too high, describing that the aircraft might be in a dangerously nose up position, the FCC will gain control of the horizontal stabilizer using a linear motor (FIG 1), thus bringing the nose of the aircraft down into safer pitch angle range (FIG 2). a. What is the input/output of the control system? b. Is this system is a close loop or open loop? c. What is the actuator used in this control system? d. Draw the Block Diagram to describe the control system. Horizontal stabilizer Pivot Horizontal stabilizer 000000c Jackscrew moves the angle of the horizontal stabilizer up or down. Motor Figure…
Which of the following terms is applied to the study of systems in a constant state of motion? Select one: a. dynamics b. statics c. plyometrics d. anthropometrics
a) Explain what do these terms mean: fmep, mfmep, pmep, amep, imep, bmep. b) Write the equation relating fmep to mfmep, pmep, and amep. c) Write the equation relating fmep to imep and bmep. d) At a given engine speed, the following parameters are obtained as follows: 1600 bmep kPa 228.45 fmep kPa 124.38 mfmep kPa 29.52 amep kPa Calculate the net indicated mean effective pressure at the same engine speed.
Problem 1: You are working in a consulting company that does a lot of hand calculations for designs in Aerospace Industry for mechanical, thermal, and fluidic systems. You took the Virtual engineering course, and you want to convince your boss and the team you work to move to modelling and simulation in computers using a certain software (Ansys, Abaqus, etc). Discuss the benefits and pitfalls of computer based models used within an industrial environment to solve problems in engineering.
Question 45 is based on the following picture. Reprinted with permission from Popular Science magazine, ©2000, Times Mirror Magazines, Inc. 45. Stuart Wilkinson, the engineer of "Chew- Chew" said, "we stole the idea of eating food from the biological world, but we are marrying that idea to useful robotic capabilities." Which of the following would not be an application of Stuart Wilkinson's theory? A. A leaf mulcher that feeds on foliage B. a trash compactor that feeds on garbage dos C. a lawn mower that feeds on grass bos 9D. a garden cultivator that feeds on soil clippings E. a recycling truck that feeds on petroleum conjo