Solve the problem in a short bond paper. A Generator supplies power to a 12-kW load 183 meters away and a second load of 8kW was 122 meters farther from load 2. For the given voltages calculate; a.Resistance of each wire of feeder from load 1 to 2 b.Resistance of each feeder from load 2 to the generator c.Efficiency of the transmission

Solve the problem in a short bond paper. A Generator supplies power to a 12-kW load 183 meters away and a second load of 8kW was 122 meters farther from load 2. For the given voltages calculate; a.Resistance of each wire of feeder from load 1 to 2 b.Resistance of each feeder from load 2 to the generator c.Efficiency of the transmission

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.33P: Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage...

See similar textbooks

Similar questions

A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and L=40mH. (a) Determine the power factor of the circuit and state whether it is lagging or leading. (b) Determine the real and reactive power absorbed by the load. (c) Calculate the peak magnetic energy Wint stored in the inductor by using the expression Wint=L(Irms)2 and check whether the reactive power Q=Wint is satisfied. (Note: The instantaneous magnetic energy storage fluctuates between zero and the peak energy. This energy must be sent twice each cycle to the load from the source by means of reactive power flows.)
The reactance of a generator is given as 0.1 pu based on the generator of 17 KV, 300 MVA. Determine the pu reactance on a base of 17 KV, 250 MVA. New pu reactance is.......
1. A single-phase power system as shown in Figure 1 consists of a 240 V, 60 Hz generator supplying a load, Zod = 8 + j6 Q through a transmission line of impedance, Zne = 0.08 + j0.14 Q. Answer the following questions: (1) transformer, T; and T2. Determine the voltage at the load and transmission line losses without the (ii) Determine the voltage at the load and transmission line losses with the transformer, T, and T2. T1 T2 1:10 10:1 IG Zaine Zioad source Figure 1
If the load draws a current of 2727 A, in phase, from a generator, which of the following statement is true? O A. The reactive power is flowing from generator to the load and the real power is flowing from the load to the generator. O B. Since the current is in phase with the generator voltage, both the real and reactive power is flowing from the generator to the load. O .Since the current is leading the generator, both the real and reactive power is flowing from the load to the generator. O D. The real power is flowing from generator to the load and the reactive power is flowing from the load to the generator. O E. None of the other choices are correct
In a Three-phase alternator, a given field current produces an armature current of 250 A on short-circuit and a generated e.m.f. of 1500 V on open-circuit. Calculate the terminal p.d. when a load of 250 A at 6.6 kV and 0.8 p.f. lagging is switched off. Calculate also the regulation of the alternator at the given load. Subject: Electrical engineering
A three phase 500 MVA, 22 kV generator has winding reactance of 1.065 Ω. Find its per-unit reactance. a. 1.002 b. 1.1002 c. 1.2002 d. 1.3002
Q2) A 13.2-kV single-phase generator supplies power to a load through a transmission line. The load's impedance is Zload = 500 236.87° ohm, and the transmission line's impedance is Zline = 60 253.1° ohm. To reduce transmission line losses to 0.0103 of its losses without using the transformers design and use two transformers T1 between the generator and the transmission line and T2 between the transmission line and the load.
e = 0 Q1: What does happen if we change two currents? a. Q2: What does happen if we have a three-phase four poles machine? Q3: What does happen if we have a two-phase two poles machine? e = 0 Q4: What does happen if we apply a capacitance in phase b and then use same voltage for both phase. Dr. Ali Ki. pw --
Q2) A 13.2-kV single-phase generator supplies power to a load through a transmission line. The load's impedance is Ztoad 500 236.87° ohm , and the transmission line's impedance is Zine = 60 253.1° ohm. To reduce transmission line losses to 0.0103 of its losses without using the transformers design and use two transformers T1 between the generator and the transmission line and T2 between the transmission line and the load.
5. Solve the following problem: A THREE-PHASE GENERATOR SUPPLIES THREE LOADS IN PARALLEL BY MEANS OF A TRANSMISSION LINE (CONDUCTORS) OF 0.4 + J0.5 OHMS. LOAD No1 5.0 KVA AND POWER FACTOR OF 0.85 BACK. LOAD No2 8.0 KW AND 3.0 KVAR. LOAD No3 6.0 KVA, POWER FACTOR OF 0.80 BACK AND 480 VOLTS. DETERMINE THE GENERATOR PARAMETERS (POWER, POWER FACTOR, OHMS, CURRENT AND VOLTAGE MAGNITUDE).
In the system shown in Figure 1, the transformers are connected star-star with both star points grounded and the generator is connected in star with its star points grounded. The per unit impedances of each element on a 40 MVA base are given in Table 1 and the voltage levels are given in Table 2. Z [p.u.] 0 2 tööt Generator 0.01 +j0.08 p.u. L Figure 1: A section of the distribution system Transformer T1 Line V BASE [KV] 0.04 + j 0.03 + j 0.15000000000000002 0.06000000000000000 Generator Table 1: Sequence impedances (p.u. on 40 MVA base) 3 T2 181. Line 3 10 Table 2: Voltage bases (kV) Load 1 Transformer T2 Load Current A load current of 11.316 kA is flowing with a lagging power factor of 90 %. Convert this to a current vector in per-unit. IL = 0.04 + j 0.06000000000000000
The input power to a 3-phase load is measured as 16kW. If the line current and power factor of the load are 21 A and 0.8 , then the value of line voltage is The field winding of DC. generator has capable of carrying the full-load current and it is usually made few turns of heavy gauge wire. separately excited Compound Shunt O Series