Solid shaft AB of the pulley assembly shown in the figure has a diameter of 2.000 in. The length dimensions of the assembly are a = 3.000 in., b = 5.250 in, and c = 4.250 in, and the diameter of the pulley is 4.750 in. The pulley belt tension is P = 155 Ib. Determine the absolute maximum shear stress for point K, which is located on the side of the shaft. b K H B D

Solid shaft AB of the pulley assembly shown in the figure has a diameter of 2.000 in. The length dimensions of the assembly are a = 3.000 in., b = 5.250 in, and c = 4.250 in, and the diameter of the pulley is 4.750 in. The pulley belt tension is P = 155 Ib. Determine the absolute maximum shear stress for point K, which is located on the side of the shaft. b K H B D

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.2.4P: Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.

See similar textbooks

Similar questions

Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 66 mm and G = 33.38 GPa. For the steel segment BC, the diameter is 40 mm and G = 83.55 GPa. Given that a = 2.12 m and b = 1.44 m, compute the largest torque T (in Nm) that can be applied as shown in the figure if the maximum shear stress is limited to 66.04 MPa in the bronze and 81.48 MPa in the steel. Round off the final answer to two decimal places.
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 70 mm and G = 33.29 GPa. For the steel segment BC, the diameter is 40 mm and G = 84.85 GPa. Given that a = 2.03 m and b = 1.38 m, compute the largest torque T (in Nm) that can be applied as shown in the figure if the maximum shear stress is limited to 64.59 MPa in the bronze and 84.39 MPa in the steel. Round off the final answer to two decimal places. d A Bronze B Steel b. Add your answer
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 75 mm and G = 35 GPa. For the steel segment BC, the diameter is 50 mm and G = 83 GPa. Given that a = 2 m and b = 1.5 m, compute the largest torque T in kN-m that can be applied as shown in the figure if the maximum shear stress is limited to 60 MPa in the bronze and 80 MPa in the steel. Answer in 2 decimal places
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 68 mm and G = 34.84 GPa. For the steel segment BC, the diameter is 40 mm and G = 83.59 GPa. Given that a = 2 m and b = 1.5 m, compute the largest torque T (in Nm) that can be applied as shown in the figure if the maximum shear stress is limited to 69.92 MPa in the bronze and 87.06 MPa in the steel. Round off the final answer to two decimal places. d ... A Bronze B Steel b.
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 66 mm and G = 34.74 GPa. For the steel segment BC, the diameter is 45 mm and 6 = 84.1 GPa. Given that a = 2.18 m and b = 1.43 m, compute the largest torque T (in Nm) that can be applied as shown in the figure if the maximum shear stress is limited to 65.48 MPa in the bronze and 81.24 MPa in the steel. Round off the final answer to two decimal places. d ... A Bronze B Steel b–
Q3/ Two shaft is attached to a rigid wall at each end. For the bronze segment AB. the diameter is 75 mm and G = 35 GPa. For the steel segment BC, the diameter is 55 mm and G = 83 GPa. Given that a-2 m and b-1.5 m. compute the largest torque T that can be applied as shown in the figure if the maximum shear stress is limited to 60 MPa in the bronze and 80 MPa in the steel. Bronze Steel
he compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 75 mm and G = 35 GPa. For the steel segment BC, the diameter is 50 mm and G = 83 GPa. Given that a = 2 m and b = 1.5 m, compute the largest torque T in kN-m that can be applied as shown in the figure if the maximum shear stress is limited to 60 MPa in the bronze and 80 MPa in the steel.
3. Four pulleys are attached to the 50-mm-diameter aluminum shaft. If torques are applied to the pulleys as shown in the figure, determine the maximum shear stress in each segment and the angle of rotation of pulley D relative to pulley A. Use G = 28 GPa for aluminum. a. Tab= b. Tbc= C. Tbc= ad= 1100 N·m 800 N·m D C 900 N·m 600 N m B A 2 m3 m2 m
M (1) M 6 mm 2) P= 10 kN. The pin at point M has a radius R. If: 8 mm F.S.=2.5 a=250 mm & b=200 mm Angle between line of action of P and X-axis is 70⁰ Ultimate shearing stress at pin = 60 MPa Ultimate bearing stress at support posts= 150 Mpa Determine the minimum value of R 6 mm
Q1: The shaft BC is hollow with inner and outer diameters of 100 mm and 120 mm respectively. Shaft AB and CD are solid and of diameter d. For the loading shown determine the maximum and minimum shear stress in shaft BC. 0.9 m 0.7 m d 0.5 m A 120 mm T = 10 kN.m i В TB = = 20 KN.m 1 C D Tc = 30 KN.mi Tp = 6 kN - m Figure Question1
4) A 50 mm diameter solid steel shaft supports loads P₁= 1.5 KN and Pc = 3.0 KN, as shown. Assume L₁ = 150 mm, L₂=300 mm, and L3=225 mm. The bearing at B can be idealized as a roller support and the bearing at D can be idealized as a pin support. Determine the magnitude and location of (a) the maximum horizontal shear stress in the shaft and (b) the maximum tension bending stress in the shaft. P Ly B L₂ C Pc L3 D