Answer 20-22 SITUATION IV:A tension member is shown below ands subjected to a dead load of 15 kN anda live load of 20 kN. USE LRFD. Thediameter of the bolts is 16 mm. GrossArea is 150 mm?. Use Fy=250 MPa,Fu=375 MPa.100017. Compute for the safe load thatcould be carried by the tensionmember.a. 150 kNb. 500 kN c. 350 kNd. 550 kN18. Solve for the design loadPbased on yielding of gross section.a. 506.25 kNc. 350.45 kNb. 500 kNd. 316.62 kN19. Solve for the design load Pbased on ruplure of the net area.Use additional 2mm for diameter ofhole and thickness of plate is 5 mm.a. 506.25 kNb. 500 kNc. 350.45 kNd. 316.62 kN20. What is the design strength forLRFD?a. 506.25 kNb. 421.88 kNC. 350.45 kNd. 316.62 kN21. What is the design strength forASD for the rupture of the net area?a. 506.25 kNb. 500 kNc. 350.45 kNd. 264.375 kN22. Compute for the block shearstrength if the plate, see the cutsection 1 for reference.a. 481.50 kNc. 372.50 kNb. 532.50 kNd. 264.38 kN

Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

SITUATION IV: A tension member is shown below and s subjected to a dead load of 15 kN and a live load of 20 kN. USE LRFD. The diameter of the bolts is 16 mm. Gross Area is 150 mm². Use Fy-250 MPa. Fu=375 MPa. 000 17. Compute for the safe load that could be carried by the tension member. a. 150 kN b. 500 kN

SITUATION IV: A tension member is shown below and s subjected to a dead load of 15 kN and a live load of 20 kN. USE LRFD. The diameter of the bolts is 16 mm. Gross Area is 150 mm². Use Fy-250 MPa. Fu=375 MPa. 000 17. Compute for the safe load that could be carried by the tension member. a. 150 kN b. 500 kN

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter3: Tension Members

Section: Chapter Questions

Problem 3.5.2P

See similar textbooks

Similar questions

PROBLEM 7. Determine the largest load P that can be applied the plate and bolts. The bolt has a diameter of 12 mm and an allowable shear stress of 80 MPa. Each plate has an allowable tensile stress of 60 MPa, an allowable bearing stress of 70 MPa, and an allowable shear stress of 30 MPa. Answer: P = 25 kips (controls) P/2 P/2 30 mm- 15 mm P 30 mm
The tension member shown in Figure 3.4-2 is a PL 5/8 x 10, and the steel is A36. The bolts are 7/8-inch in diameter. a. Determine the design strength for LRFD. b. Determine the allowable strength for ASD. | 2" +|+| in seinefrinehich 9 оо SO
The tension member shown is an L150 × 87.5 × 8. The bolts are 19 mm in diameter. If A36 steel is used, is the member adequate for a service dead load of 138 kN and a service live load of 138 kN? a. Use LRFD. b. Use ASD. 50 37.5 37.5 37.5 56.25 62.5
Prob 01: An 18” depth beam is bolted to a 24” depth girder is connected similar to that in figure shown below. Thediameter of the rivet is 20mm and the angles are each 100mm x 100mm x 12mm thick. For each bolt, assume thatthe allowable bearing stress is 220 MPa. Determine the allowable load P in KN on the connection. *show all theload P in kN for bearing stressBeam web thickness = 5mmGirder web thickness =
Problem 2. Using 22 mm diameter bolt, compute: a. t for P alone b. t for moment alone c. Critical shear stress 280KN 3 @ 195m 3 @ 200mm
5. a bolted lap joint shown in the figure below. The bolts are 20m in diameter in 23 mm holes. The plates are 12m thick X350 Allowable stress of Plates: Tenaion in gross area0.60Fy Tension in net area0.50 Fu Shear on Net Area 0.30Fu Yield Strength of plate, Fy 248 Npa Ultinate tensile strength of Plate. Fu400 Mpa x, Find the safe load P based on a- Gross area yielding b. net area rapture c. block shear 2 of 3
From the bolted connection shown, the diameter of bolts is 20 mm with the hole diameter equal to 3mm larger than the bolt diameter, the angular section is 100x75x8mm, with an area of 1340 mm^2. Thickness of gusset plate is 9 mm. the gusset plate. (a)If T = 200KN, compute the shearing stress on the bolts. (b)If the allowable shearing stress on the bolt is 145MPa, compute the value of T.
A bolted connection shown is bolted with a A-325 bolts with an allowable shearing stress of 207 MPa. A-36 steel is used. The applied force "T" is equally divided among the bolts. Assume bolt hole diameter to be 3 mm bigger than bolt diameter. Diameter of bolt is 20 mm. T/2 T T/2 10 mr 10 mm T/2 300 mm T/2 Determine the capacity of the connection if shearing governs in kN. A 1548.58 B 1170.56 1290.62 D 1439.25 000
4. An UPE 300 is to be used as a tension member and it is bolted to a 10mm thick gusset plate with bearing type 8-M20 8.8 bolts as shown in the figure below. a. Check all spacing and edge distance requirements. b. Compute the allowable tensile strength of the channel UPE 300. Don't consider shear strength of the bolts and bearing strength of the bolt holes. [all dimensions are in mm] Material both for gusset plate and UPE 300: S275 F-275N/mm² Fu=430N/mm² UPE 300 Ag = 5660 mm² tw 9.5 mm x = 28.9 mm 70 160 70 + 10mm thick gusset plate +50+ 80 -80-80-50 o +50+80 -80 80-50 UPE 300
Plate A, PL 16mm x 375mm, is connected to another plate B with 10- 22 mm o bolts as shown. The steel is A36 steel with Fy= 250 MPa and F,= 400 MPa. Assume that plate B has adequate strength. Use ASD. Plate B 375a 75 m 2 75mm Plate A 75 mm 75mm 150 50150 Compute the nominal strength based on yielding in KN.O Determine the allowable tensile strength of Plate A in KN.O Compute the allowable tensile strength at section a-1-2-2-4-c in KN.0
P4.002 Three bolts are used in the connection shown in the figure. The thickness of plate (1) is 15 mm. The ultimate shear strength of the bolts is 350 MPa, and the ultimate bearing strength of plate (1) is 375 MPa. Determine the minimum bolt diameter required to support an applied load of P = 155 kN if a minimum factor of safety of 2.8 is required with respect to both bolt shear and plate bearing failure. Answer: dbolt min = (1) mm
H.W The omPound shaft Shown isattached to Kigid SuPprts, for the bronze Segment AB, the diameter is 75mm G=35 GN/m and TS60MNIM. for steel Segment Bc, the dlameter is Somm, G= 836N/mand TS8OMNIMIF a=2m and b= 1.5m,lam Pute the maximum torguelT) that Gan be applier?