Situation 04. A water hose is used to fill a rectangular tank of width H and height twice as its width. The hose jets out water 45° from the horizontal the same level as the bottom of the tank. If the distance of the hose to the tank is 6 times its width, compute the maximum initial velocity so that the water will still enter the tank. Express your answers in terms of H.

Situation 04. A water hose is used to fill a rectangular tank of width H and height twice as its width. The hose jets out water 45° from the horizontal the same level as the bottom of the tank. If the distance of the hose to the tank is 6 times its width, compute the maximum initial velocity so that the water will still enter the tank. Express your answers in terms of H.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Fluid mechanis Read the question carefully, give me right solution The head loss (hf) in a 1200mm x 600mm pipe (therefore, non-circular) conveying water is estimated to be 0.04m for every 1 meter of its total length. If the said pipe is filled with water and its friction factor f = 0.032, what should be the discharge Q?
Problem II. A proposed elevated tank for a certain community has a diameter of 72 inches and a height of 120 inches. It is to draw water by a pump from an aquifer down below the ground. Two steel hoops, 24.4 in? in cross section, are installed around the tank, one at the bottom and one at the top, to prevent the bursting of the tank by the water pressure inside. (Use unit weight of water, ywater = 62.4 lb/ft³) a) Compute the internal stress at the bottom of the tank (in psf). b) Determine the tensile stress at the top (in psi). c) Determine the tensile stress at the bottom (in psi).
SUPPLEMENTARY QUESTION The figure shows two reservoirs connected by a pipe. The discharge rate in the pipe is known to be equal to SN/100 (m3/s) (where SN is the sum of your student number). Calculate the height of the second reservoir (H2), and the pressure head, velocity head and elevation head at point 3 (mid-point of the pipe). Hi 300 m H datum A = SN/1000 %3D L = 100 x SN (m) %3D D = 0.3 m
Situation 4: A 200 m of rubber cotton lined hose having a diameter of 75 mm is attached to a hydrant at which pressure is 450 kPa during the flow. Assume the hose to be horizontal and f = 0.023 39. At what rate will the water be discharged trough the rubber cotton lined hose 17 L/s 16L/s 15L/s 14 L/s 40. If a 25 mm diameter nozzle is attached to the hose, what would be the expected head lost if a pressure of 500 kPa in the hydrant is maintained? Use Cv = C = 0.96 21.9 m 24.3 m 22.8 m 23.5 m 41. What is the discharge may be expected if the 25 mm nozzle is attached to the hose? 11.3 L/s 12.1 L/s 15.6 L/s 14.5 L/s
A 122-mm-diameter pipe enlarges to a 148-mm-diameter pipe. At section 1 of the smaller pipe, the density of gas in steady flow is 293.454 kg/m3, and the velocity is 23 m/s; at section 2 of the larger pipe, the velocity is 15 m/s. Find the unit weight (in kN/m3) of the gas at section 2. Round off to three decimal places.
Oil (SG=0.82) entering a pump through an 180mm diameter pipe at 35kPa has a flow rate of 0.07 m^3/s. It leaves the pump through a 120mm diameter pipe at 120 kPa. Assuming that the suction and discharge sides of the pump are at the same elevation, find the horsepower delivered to the water by the pump (746 watts = 1 HP). Illustrate the problem and show your complete solution.
A cylindrical tank, containing water, with a diameter of 3 m and a water level of 5 m is to be drained. Calculate : 1.The time taken in minutes to empty the tank if two orifices in the bottom with a diameter of 50 mm and coefficient of discharge Cd=0.785 2.the time taken in minutes to empty the tank, if a pipe with internal diameter of 50 mm, length of 6 m and coefficient of friction of 0,008,respectively, and the outlet 2 m below the bottom. 3.the time taken in minutes to empty the tank, if a pipe with internal diameter of 50 mm and length of 6 m respectively, an outlet 4 m below the bottom,and a valve with a loss factor of 2,8. Kindly note there's no diagram I can provide it's just those questions.
Pipelines 1, 2, and 4 are connected in series, while pipelines 2 and 3 are connected in parallel. The rate flowing from pipe 1 is 20 L/s. The value of the friction factor "f' is 0.003 for all pipes. (4 A B Diameter Length (mm) (m) 200 3000 Pipe 2 300 2200 3 200 3200 4 400 2800 1.Determine flow rate in pipe 2. 2.Find the flow rate in pipe 3. 3.Calculate total head loss of the system. 4.Check the values calculated by equating the calculated flow rate in pipes 2 and 3 to the total flow rate.
11. A 350 mm by 150 mm venturi meter is installed in a vertical pipeline carrying water as shown in the figure. The flow is upward through the meter. A differential manometer containing carbon tetra-chloride (sg=1.5) is attached to inlet and throat. The difference Z in gage level is 700 mm. Neglecting the head loss, compute the discharge of the venturi meter 350 mm 150 mm 300 mm 700 mm
A horizontal venturimeter with a 100 mm diameter throat section is used to measure the volume flow rate of water at 20°C in a 200 mm pipeline. If the pressure in the pipeline at the entrance to the venturi meter is 480 kPa and the pressure in the throat of the venturi meter is measured 400 kPa, estimate the actual flowrate (Qact) in the pipe in liters per second. Assume the velocity coefficient (C) of the venturi meter as 0.98 and the contraction coefficient (CC) as 0.99. Use the density of water at 20°C from Table B.2 (998.2 kg/m³). P1 Section 1 P2 Section 2 (Throat) -Flow- Streamline
Please answer in complete and clear solution thank you Question A fluid is flowing into an inverted conical tank, 14in diameter on top and 24in deep at a rate of7in3/min. Find how fast the water surface is rising when the fluid is 8in deep in the tank.
Two pipes 1 and 2 having the same length and diameter are in parallel. If the flow in pipe 1 is 750 liters per second, what is the flow in pipe 2 if the friction factor f of the second pipe is twice that of the first pipe? Select one: O a. 680 liters per second O b. 530 liters per second O c. 560 liters per second O d. 620 liters per second