Show your step by step solutions. 6. With a wooden ruler, you measure the length of a rectangular piece of sheet metal to be 16 mm. With micrometer calipers, you measure the width of the rectangle to be 5.98 mm. Consider 4 significant figures only. Determine: (d) the difference between the length and the width; and (e) the ratio of the length to the width?

Show your step by step solutions. 6. With a wooden ruler, you measure the length of a rectangular piece of sheet metal to be 16 mm. With micrometer calipers, you measure the width of the rectangle to be 5.98 mm. Consider 4 significant figures only. Determine: (d) the difference between the length and the width; and (e) the ratio of the length to the width?

Glencoe Physics: Principles and Problems, Student Edition

1st Edition

ISBN:9780078807213

Author:Paul W. Zitzewitz

Publisher:Paul W. Zitzewitz

Chapter1: A Physics Toolkit

Section1.3: Measurement

Problem 19SSC

See similar textbooks

Similar questions

(a) A person's blood pressure is measured to be 1202 mm Hg. What is its percent uncertainty? (b) Assuming the same percent uncertainty, what is the uncertainty in a blood pressure measurement of 80 mm Hg?
2.) A single reading taken with a meter stick for the length of a cylinder is 5.5 cm. What is the prsable percent error in the reading? 3.) The following readings were taken with a meter stick for the length of a cylinder: 5.5 cm, 5.3 cm, 5.4 cm, 5.5 cm and 5.6 cm. Calculate the standard deviation of the mean, the stand error and the probable percent error. 4.) How many significant figures should be given in reporting the length of the cylinder in question 3? 5.) If the radius of the cylinder in question 2 is 2.4 ± 0.2 cm and its mass is 32.6 ± 0.5 gm, what will be the probable percent error in the density of the cylinder? What will be the probable error in density? How many significant figures should be given in reporting the density? Conclusions?? 02 6) (figure3) 6a)Befer to Figure 3. Given a track length of 90 cm and a height difference of 18 cm, what is sin 6 02 01 Fig. 2 Z)(figure 2) plane (see Figure 2). Attach the diagram in question#8 below. What would be the acceleration given…
If the number of significant figures is 6, what is the value of the pre-specified Error(?s) Select one: O a 0.000005% O b. 0.0005% O c. 0.005% ০ d 0.00005%
Please answer 1-3 sub-units.7. A box measures 3.12 ft m length, 0.0455yd in width and 7.87in in height. What is it volume in cubic centimeter?8. A block occupied 0.2587ft3. What is its volume in mm3?9. If you are going 55mph. What is your speed in nm per second?
Problem 4: Significant Figures A block of gold has length 5.62 cm, width 6.35 cm, and height 2.78 cm. a. Calculate the base area and round up the answer to the appropriate number of significant figures. b. Now multiply the rounded result of part (a) by the height and again round, obtaining the volume. Let this be ?1. c. Now obtain volume 2, ?2, by first finding the width times the height, rounding up to appropriate significant figures, and multiply by the length. d. Explain why the answers don’t agree with the third significant figure.
State the number of significant digits and the implied precision of the given number. The number 1.928×10^4 has........ significant digits (type a whole number) B. What is the implied precision of the number 1.928×10^4 s? A. The number is precise to the nearest hundred seconds B. The number is precise to the nearest second. C. The number is precise to the nearest ten seconds
SEND THE ANSWER IN 10 MINUTES PLEASE Assume that you measure the dimensions of a cylinder with a vernier caliper many times and obtain the following average values in cm: Height : 6 Diameter:1.13 Using these values, calculate the volume of cylinder in cm. Express your result with 3 significant figures. Take PI as 3.14
The following data sets are the length measurements of a raw material. The actual length of the part is supposed to be 3.2 mm. Which sets) do you prefer to the others? Briefly explain.HINT: Check the accuracy and the precision of each data set.Data Set 1: 2.91, 3.00, 3.50, 2.85, 3.22, 3.15, 3.49, 2.90, 3.27, 3.15Data Set I1: 3.13, 3.22, 3.19, 4.17, 3.21, 2.62, 3.25, 2.80, 2.40, 3.81Data Set I: 3.24. 3.18. 3.22. 3.20. 3.17, 3.23, 3.19, 3.20, 3.16, 3.24Data Set IV: 2.90. 3.00. 2.92. 2.95. 2.93. 2.97. 2.94. 2.99. 2.96, 3.00 Please donot provide solution in image format and it should be in step by step format and provide fast solution
The radius of a circular disk is given as 19 cm with a maximum error in measurement of 0.2 cm. (a) Use differentials to estimate the maximum error in the calculated area of the disk. (Round your answer to two decimal places.) 23.88 cm? (b) What is the relative error? (Round your answer to four decimal places.) 0.021 What is the percentage error? (Round your answer to two decimal places.) 2.10% X % Enhanced Feedback Please try again. Keep in mind that for a disk of radius r, its area is given by A Tr. You can take the differentials on both sides of this formula to obtain an expression for dA. This differential is a good estimate of the largest possible error AA. Finally, use the given values of r and dr (measurement error) to approximate the error, AA = dA, relative error, dA dA x 100% . A AA ΔΑ and percentage error, A x 100% = A A Need Help? Read It
Part B: Adora needs to find the area of a table top. She measures the table width to be 0.8673m and the table length is 1.405m. If the known value for the area of the table is 1.185 sq. meter, what is the percent error between the area Adora finds and the known area?
B. Solve the following problems using differentials and linear approximations. Show complete solutions 4. The dimensions of a rectangle are measured to be 8 0.1 by 4 0.2 inches. What is the approximate uncertainty in the area measured?
Hi could you please answer these with complete solution PROBLEM : Several carpet installers make measurements for carpet installation in the different rooms of a restauran reporting their measurements with inconsistent accuracy, as compiled in Table 1.6. Compute areas for (a) the banquet hall, (b) the meeting room, and (c) the dining room, taking into account significant figures. (d) What total area of carpet is required for these rooms?