Fast pls Show by dimensional analysis that this leads to the logarithmic overlap relation (6.28).The following turbulent flow velocity data u(y), for air at24°C and 1 atm near a smooth flat wall were taken in theUniversity of Rhode Island wind tunnel:Y, mm0.640.891.191.401.65и, m/s15.616.517.317.618.0Estimate (a) the wall shear stress and (b) the velocity u aty = 5.6 mm.

Given DataT=24°Ckinematic viscosityϑ=1.543×10-5m3/sDensityρ=1.225kg/m3

Answered: Show by dimensional analysis that this…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In the field of air pollution control, one often needs to sample the quality of a moving airstream. In such measurements a sampling probe is aligned with the flow as sketched in Fig. A suction pump draws air through the probe at volume flow rate V· as sketched. For accurate sampling, the air speed through the probe should be the same as that of the airstream (isokinetic sampling). However, if the applied suction is too large, as sketched in Fig, the air speed through the probe is greater than that of the airstream (super iso kinetic sampling). For simplicity consider a two-dimensional case in which the sampling probe height is h = 4.58 mm and its width is W = 39.5 mm. The values of the stream function corresponding to the lower and upper dividing streamlines are ?l = 0.093 m2/s and ?u = 0.150 m2/s, respectively. Calculate the volume flow rate through the probe (in units of m3/s) and the average speed of the air sucked through the probe.
Consider laminar flow through a long section of pipe, as in Fig. For laminar flow it turns out that wall roughness is not a relevant parameter unless ? is very large. The volume flow rate V· through the pipe is a function of pipe diameter D, fluid viscosity ? , and axial pressure gradient dP/dx. If pipe diameter is doubled, all else being equal, by what factor will volume flow rate increase? Use dimensional analysis.
(b) A wind-tunnel experiment is performed on a small 1:5 linear-scale model of a car, in order to assess the drag force F on a new full-size car design. A dimensionless "drag coefficient" Ca is defined by C, =- pu'A where A is the maximum cross-sectional area of the car in the flow. With the model car, a force of 3 N was recorded at a flow velocity u of 6 m s. Assuming that flow conditions are comparable (i.e., at the same Reynolds number), calculate the expected drag force for the full-sized car when the flow velocity past it is 31 m s (equivalent to 70 miles per hour). [The density of air p= 1.2 kg m.]
Dimensional analysis can be used in problems other than áuid mechanics ones. The important variablesaffecting the period of a vibrating beam (usually designated as T and with dimensions of time) are the beamlength `, area moment of inertia I, modulus of elasticity E, material density , and Poissonís ratio , so thatT = f cn(`; I; E; ; )Recall that the modulus of elasticity has typical units of N/m2 and Poissonís ratio is dimensionless.(a) Find dimensionless version of the functional relationship.(b) If E and I must always appear together (meaning that EI is e§ectively a single variable), Önd a dimensionless version of the functional relationship.
Mott ." cometer, which we can analyze later in Chap. 7. A small ball of diameter D and density p, falls through a tube of test liquid (p. µ). The fall velocity V is calculated by the time to fall a measured distance. The formula for calculating the viscosity of the fluid is discusses a simple falling-ball vis- (Po – p)gD² 18 V This result is limited by the requirement that the Reynolds number (pVD/u) be less than 1.0. Suppose a steel ball (SG = 7.87) of diameter 2.2 mm falls in SAE 25W oil (SG = 0.88) at 20°C. The measured fall velocity is 8.4 cm/s. (a) What is the viscosity of the oil, in kg/m-s? (b) Is the Reynolds num- ber small enough for a valid estimate?
A tiny aerosol particle of density ?p and characteristic diameter Dp falls in air of density ? and viscosity ?. If the particle is small enough, the creeping flow approximation is valid, and the terminal settling speed of the particle V depends only on Dp, ? , gravitational constant g, and the density difference (?p − ? ). Use dimensional analysis to generate a relationship for V as a function of the independent variables. Name any established dimensionless parameters that appear in your analysis.
A liquid of density ? and viscosity ? is pumped at volume flow rate V· through a pump of diameter D. The blades of the pump rotate at angular velocity ? . The pump supplies a pressure rise ΔP to the liquid. Using dimensional analysis, generate a dimensionless relationship for ΔP as a function of the other parameters in the problem. Identify any established nondimensional parameters that appear in your result. Hint: For consistency (and whenever possible), it is wise to choose a length, a density, and a velocity (or angular velocity) as repeating variables.
Q.5 A plate 1 mm distance from a fixed plate, is moving at 500 mm/s by a force induces a 2 shear stress of 0.3 kg(f)/m. The kinematic viscosity of the fluid (mass density 1000 kg/ 3. m) flowing between two plates (in Stokes) is
An underwater device which is 2m long is to be moved at 4 m/sec. If a geometrically similar model 40 cm long is tested in a variable pressure wind tunnel at a speed of 60 m/sec with the following information, Poir at Standard atmospheric pressure = 1.18kg/m³ Pwater = 998kg/m3 Hair = 1.80 x 10-5 Pa-s at local atmospheric pressure and Hwater = 1 × 10-3 Pa-s then the pressure of the air in the model used times local atmospheric pressure is
Question 3 The aerodynamic derivative X, may be determined from the following expression: X -pU SCD %3D where p is the air density, S is the wing area, U is the airspeed, and Cp is the drag coefficient. Consider an aircraft of weight 68 kN and wing area 43 m?, flying straight and level under international standard atmosphere (ISA) conditions, where p 1.018 kg/m, at an airspeed of 155 m/s. The aircraft %3D has a drag polar Cp = 0.011 + where Ci is the lift coefficient. Calculate the value of X, at this flight condition. Give your answer in units of Ns/m.
Particles in liquids achieve terminal speed very quickly. One can measure the time it takes for a particle to fall a certain distance and then calculate the constant B. Suppose a steel ball bearing (mass=0.86 grams) is dropped in a container of motor oil. It takes 12 s to fall 0.60 m. (a) Estimate the terminal speed, Viem, assuming the ball bearing reaches terminal speed almost immediately. (answer: Vterm 0.050 m/s) (b) Calculate B. (answer: 0.17 kg/s) (e) What is the speed of the ball bearing 11 ms after it is dropped? (answer: 0.044 m/s)
Ex. The force required to tow a 1:30scale model of a motor boat in a lake at a speed of 2m/s is 0.5 N, Assuming that the viscosity resistance due to water and air is negligible in comparison with the wave resistance, calculate the corresponding speed of the prototype for dynamically similar conditions. What would be the force required to propel the prptype at that velocity in the same lake? Ans.: 10.95m/s, 13500N

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS