show an arrow pushing mechanism for the reaction between α-phellandrene and maleic anhydride. Explicitly identify which reactant is the diene and which is the dienophile. Mark the chiral carbon on the α-phellandrene with a *. Draw the 4 possible products from the reaction between α-phellandrene and maleic anhydride. These should include an (R)-endo, (R)-exo, (S)-endo, (S)-exo.

Chemistry
10th Edition
ISBN:9781305957404
Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste
Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste
Chapter1: Chemical Foundations
Section: Chapter Questions
Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...
icon
Related questions
icon
Concept explainers
Question

show an arrow pushing mechanism for the reaction between α-phellandrene and maleic anhydride. Explicitly identify which reactant is the diene and which is the dienophile. Mark the chiral carbon on the α-phellandrene with a *.

Draw the 4 possible products from the reaction between α-phellandrene and maleic anhydride. These should include an (R)-endo, (R)-exo, (S)-endo, (S)-exo.

Which set of products would be predicted as the major product, endo- or exo-? Explain your reasoning.

Transfer Hydrogenation of 4-(p-hydroxyphenyl)-3-buten-2-one
Pd/ Alumina Cat.
Sodium Formate
CH3 Methanol K,CO,(sat
CH3
но
но
To a 25 ml round bottom flask equipped with a stir bar is added 7 ml of a 0.25M solution of
potassium carbonate in methanol (Saturated Solution) and 490 mg of sodium formate and 295 mg of 4-
(p-hydroxyphenyl)-3-buten-2-one. Initiate stirring. Next add 120 mg of 5% Palladium on alumina. Fit a
water cooled condenser to the round bottom flask. Heat the solution to reflux (boiling) on a sand bath
set to 120°C. Note the time the solution starts to boil. Reflux the solution for an additional 60 minutes.
Remove the reaction from the heat and allow it to cool. Pour the reaction mixture into a separtory
funnel. Rinse the round bottom flask with 25 mL of MTBE and add to the separtory funnel. Add 15 mL
of water to the separatory funnel and shake well with periodic venting to avoid pressure buildup.
Separate the layers. Extract the aqueous layer with 15 ml of fresh MTBE. Separate the layers and then
combine the two MTBE layers from each extraction. Extract the combined organic layer with 15 mL of
saturated NaCl solution. Dry the organic layer with anhydrous sodium sulfate. Transfer the organic
layer into a pre weighed beaker with a boiling chip.
Boil off the solvent on a sand bath set to 120°C.
The product will be a thick liquid that should solidify on cooling. Carefully waft the air over the beaker
to see what your product smells like. After getting its weight obtain a MP and IR spectra of your
product.
Transcribed Image Text:Transfer Hydrogenation of 4-(p-hydroxyphenyl)-3-buten-2-one Pd/ Alumina Cat. Sodium Formate CH3 Methanol K,CO,(sat CH3 но но To a 25 ml round bottom flask equipped with a stir bar is added 7 ml of a 0.25M solution of potassium carbonate in methanol (Saturated Solution) and 490 mg of sodium formate and 295 mg of 4- (p-hydroxyphenyl)-3-buten-2-one. Initiate stirring. Next add 120 mg of 5% Palladium on alumina. Fit a water cooled condenser to the round bottom flask. Heat the solution to reflux (boiling) on a sand bath set to 120°C. Note the time the solution starts to boil. Reflux the solution for an additional 60 minutes. Remove the reaction from the heat and allow it to cool. Pour the reaction mixture into a separtory funnel. Rinse the round bottom flask with 25 mL of MTBE and add to the separtory funnel. Add 15 mL of water to the separatory funnel and shake well with periodic venting to avoid pressure buildup. Separate the layers. Extract the aqueous layer with 15 ml of fresh MTBE. Separate the layers and then combine the two MTBE layers from each extraction. Extract the combined organic layer with 15 mL of saturated NaCl solution. Dry the organic layer with anhydrous sodium sulfate. Transfer the organic layer into a pre weighed beaker with a boiling chip. Boil off the solvent on a sand bath set to 120°C. The product will be a thick liquid that should solidify on cooling. Carefully waft the air over the beaker to see what your product smells like. After getting its weight obtain a MP and IR spectra of your product.
Expert Solution
trending now

Trending now

This is a popular solution!

steps

Step by step

Solved in 3 steps with 2 images

Blurred answer
Knowledge Booster
Reactive Intermediates
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, chemistry and related others by exploring similar questions and additional content below.
Similar questions
  • SEE MORE QUESTIONS
Recommended textbooks for you
Chemistry
Chemistry
Chemistry
ISBN:
9781305957404
Author:
Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste
Publisher:
Cengage Learning
Chemistry
Chemistry
Chemistry
ISBN:
9781259911156
Author:
Raymond Chang Dr., Jason Overby Professor
Publisher:
McGraw-Hill Education
Principles of Instrumental Analysis
Principles of Instrumental Analysis
Chemistry
ISBN:
9781305577213
Author:
Douglas A. Skoog, F. James Holler, Stanley R. Crouch
Publisher:
Cengage Learning
Organic Chemistry
Organic Chemistry
Chemistry
ISBN:
9780078021558
Author:
Janice Gorzynski Smith Dr.
Publisher:
McGraw-Hill Education
Chemistry: Principles and Reactions
Chemistry: Principles and Reactions
Chemistry
ISBN:
9781305079373
Author:
William L. Masterton, Cecile N. Hurley
Publisher:
Cengage Learning
Elementary Principles of Chemical Processes, Bind…
Elementary Principles of Chemical Processes, Bind…
Chemistry
ISBN:
9781118431221
Author:
Richard M. Felder, Ronald W. Rousseau, Lisa G. Bullard
Publisher:
WILEY