4 mBP₁SetP1=2.7kN,P2=5.2kN.E4 mP₂4 m6 mDetermine the force in member AB,AE,BC,BE,CD,CE,DE, andstate if the member is in tension or compression.

Given : P1 = 2.7 kN and P2 = 5.2 kN Determine forces in member AB, AE, BC, BE, CD, CE, DE ?

Answered: SetP1=2.7kN, P2=5.2kN. Determine the…

SetP1=2.7kN, P2=5.2kN. Determine the force in member state if the member is in tension or compression. AB,AE,BC,BE,CD,CE,DE, and

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: What is the strain energy of the massless stepped bar as shown in the figure below? [Take E = 200…

Q: Q. A bar 500 mm long and 30 mm in diameter hangs vertically and has a collar securely

A: Given- l = 500mm d = 30mm W = 150N E = 2X105 N/mm2 Free Fall Height (h) = 60 mm

Q: 3) Given the data in Table 2, what are the reduced HCR, VCRS, SDs, and HDs? Table 2: Traverse…

A: Given data:- Instrument @ C HI=1.533 m HR=1.300 m Station HCR VCR SD A 0°00'03" 84°18'09"…

Q: Q. 10. A rectangular channel 2m wide has a specific energy of 1.50m when carrying discharge of…

A: Given data: Rectangular channel Width (b)= 2 m Specific energy (E)=1.5 m Discharge velocity (Q) =…

Q: A collapsible soil sub-grade sample was tested using Standard California Bearing Ratio apparatus;…

A: Given data- The load carried by standard specimen L=1370 kg, Test results given for Standard…

Q: Compute the y-component of the resultant of the concurrent forces shown in N. P1 214 N, P2 = 421 N,…

A: The given figure is shown below:

Q: maximum in plane shear stress.

A: Given data, Inner radius of the cylindrucal tank with closed ends is, R= 1 m Thickness,t= 4 mm…

Q: this is the answer I need solutions a) no stirrup needed b) s = 275 mm c) s = 275 mm d) s = 90…

Q: A truss (Truss) is subjected to force as shown in the figure below. Try to calculate the vertical…

A: A=200mm2 E=200GPa To find vertical displacement at point C

Q: Average free flow speed and the jam density observed on a road stretch are 60 km/h and 120…

A: Given data : Average free flow speed, Vf=60 km/h Jam density, kj=120 veh/km

Q: is placed in the rain. During the rain the volume of the sample rem but the degree of saturation…

Q: projectile is launched from point A with the initial conditions shown in the figure. Determine the…

Q: Explain systematic and random error in a unique way.

A: Error: It is the devation of the value from actual value. It can be either due to mismanagement or…

Q: What is the material all about? ARTICLES…

A: Material is about Engineers at the workplace asking for help at work from their coworkers is…

Q: Which of the following indicates the correct value of precise closing error if e = 0.54 and lengths…

A: Given data Clossing error (e) = 0.54 Length of slides = 92.69m, 119.23m, 92.64m, 42.96m, and…

Q: Draw the shear and moment diagrams for the following beam.

A: Given : we are asked to draw the shear and moment diagram for the beam given above ?

Q: Cylindrical tank with closed ends is filled with compressed air at a pressure of 480 KPa. The inner…

Q: DRAW THE SHEAR AND MOMENT DIAGRAM F A 100 KN B

Q: [p = [SN5 +40]°, 0 = [SN +30]°, F₁ = 10[SN₂ +50] N, a = [SNg +46]°, B = [SN, +61]°, F₂ = 10[SN10…

Q: Find 5 internal forces of the truss members. Estimate the value and the location of 3 external axial…

Q: What will be the value of DMD for B if DMD for A is -22.87, departures for A and B will be -22.87,…

A: Using formula for DMD

Q: The maximum speed of a train on B.G. track having a curvature of 3° and cant of 10 cm with allowable…

A: Given data- B.G track- Degree of the curve D=3o, Cant=10 cm=100 mm, Allowable cant deficiency=76 mm,…

Q: For 12 mm thick cement plastering 1: 6 on 100 sq. m, new brick work, the quantity of cement required…

A: To find out the quantity of cement plastering of 12 mm thick for area of 1002.

Q: A cantilever beam has the square cross section of 10 mm x 10 mm. It carries a transverse load of 10…

Q: A rigid retaining wall of 6m height has a saturated backfill of soft clay soil. What is the critical…

A: Given data H= 6m C = 18 KN/m2 Ysat = Y = 17.56 KN/m3 Find critical height (Hc)

Q: From the following observations, what is the closing error? Line AB BC CA O Length (m) 92.96 157.63…

Q: 10 m thick confined aquifer gives the steady state discharge of 0.03 m³/s through the well of 50 cm…

A: Given- Radius of influence R=500 m, Width B=10 m, K=permeability Head H=15 m, & h=10 m, Radius…

Q: The magnitude of the vertical reaction

A: Given, Find the magnitude of the vertical reaction force in N at the left support. Where, Distance…

Q: maximum in plane shear stress.

A: Given data, Cylindrical tank with closed ends is filled with compressed air, Pressure,P= 480 KPa…

Q: Equations: F₁=M S F₁ = 3V 2A M=WL² 8 M=Pa V=WL² 2 Calculate the Maximum Shear & Moment 1. What is…

A: Point load and udl is given. Length of the beam also given. Find out minimum area of c/s and…

Q: What is the depth of the flow (m) in a circular channel of diameter 2.0 m for the maximum velocity?…

A: Given data- Circular Channel- Diameter D= 2m, To Find- The value of the depth of the flow (y).

Q: A trapezoidal section has a bottom width of 20 ft and side slope of inclination 1:1.5. Its friction…

Q: Q. 22. An irrigation channel having a trapezoidal section having side slopes 1.5 H:1V, is to carry a…

A: To design the most economic section of irrigation channel having discharge of 20 m³.

Q: Find the increment inn vertical stress

A: Given data, As per the 2:1 dispersion method of stress distribution. Determine the increment in…

Q: Q. A bar 500 mm long and 30 mm in diameter hangs vertically and has a collar securely attached at…

A: When an elastic body is loaded it undergoes deformation to resist the load. For the time it is being…

Q: 3.4 The required flexural (bending moment) strength is of a reinforced concrete beam is Mu= 260…

Q: What is the method of compaction used in bulk unit weight and voids in aggregate?

A: There are several types of method of compaction 1. Smooth wheel roller 2. Pneumatic wheel roller 3.…

Q: Find the work done if force applied on crate to displace crate through 5 m is 21 N

A: Given data : The value of displacement d=5 m The value of force applied F=21 N Required : Work…

Q: Q. A bar 500 mm long and 30 mm in diameter hangs vertically and has a collar securely attached at…

Q: Q. 10. A rectangular channel 2m wide has a specific energy of 1.50m when carrying discharge of…

Q: Utilize moment of areas method. Sketch the shear force and bending moment diagrams of the cantilever…

Q: A cantilever beam has the square cross section of 10 mm x 10 mm. It carries a transverse load of 10…

Q: In the figure shown assuming clockwise moments are positive, compute the moment of force F = 391 kN…

A: GIVEN: figure Force(F) = 391 KN Force( P)=289 KN Clockwise moment are positive To determine:…

Q: an undisturbed sample of soil has a volume of 29 cm³ and weighs 48 g. The dry weight of the sample…

Q: Problem 2-48 For the tank shown in the figure, compute the pressure at points B, C, D, and E in kPa.…

Q: Determine the y-component of the resultant of the concurrent forces in kN below. F1 = 252 kN, 01 =…

Q: Assuming a Lapple standard conventional cyclone, specify the body diameter required to achieve an…

A: Given data:- Air coming from a sugar refinery, Q = 24000 acfm Inlet velocity, v= 6000 ft/min

Q: A soil sample's liquid limit (LL) is 40 and its plastic limit (PL) is 20, the soil's plasticity…

Q: Estimate the 1998 total installed cost for the baghouse of Problem 6.4, assuming it is mild steel…

A: Given:- flow rate of air=2000m3/minconcentration of lime stone=1.50…

Q: What is the correction for the latitude of BC using the transit method? Line AB BC CA a. 183.789 b.…

A: To Determine :- correction for the latitude of BC using the transit method.

Concept explainers

Load on Structures

Civil engineers primarily deal with beams in their day-to-day applications. A beam is a structural member that resists shear loadings. There are various types of beams such as cantilever beam, simply supported beam, and over the hanging beam. All these beams have a different end and loading conditions.

Question

4 m
B
P₁
SetP1=2.7kN,P2=5.2kN.
E
4 m
P₂
4 m
6 m
Determine the force in member AB,AE,BC,BE,CD,CE,DE, and
state if the member is in tension or compression.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The truss is loaded by concentrated forces as shown in the figure. Use E = 30 x 106 psi and A = 0.90 in² for all the members. Determine the deformation sustained by members CG and FG. 12 kips 14 kips 16 kips A B с 10 kips |-6R-|-6A 8 ft ļE 5 ft ——6 ft—6 ft--6 ft-
All bars in the truss have the same cross section and material properties. Find the total change in length of the cord A-B-C, and the stress at point p in the coordinate system given. ⁹00 lb AABC = σ= in ksi A = 0.64 in² E 30000 ksi V = 0.29 point p A Y 800 lb. 5 ft B 11200 lb 5 ft C 800 lb F 4 ft 4 ft
Q3 The truss ABC shown in the figure supports a horizontal load P-900 lb and a vertical load P2= 300 lb. Both bars have cross-sectional area A-2.4 in. and are made of steel with E-20 X 10 psi. (a) Determine the strain energy U, of the truss when the load P, acts alone (P2 -0). (b) Determine the strain energy U2 when the load P2 acts alone (P 0). (c) Determine the strain energy Uz when both loads act simultaneously. 30 B P =900 lb P2 300 lb 40 in.
key answer: T2=71.15 N tension at A T2=20.21 N tension at B
If the force in member AG of the truss in the figure below is 6 kN (C), then the :force (in kN) in member BG is d1=6.1 6 kN 3 kN 3 kN 1.5di 1.5di F di В di D -0.75d1 1.5di 0.75di
Rigid bar ABC is supported by two identical solid bronze [oy = 331 MPa; E = 105 GPa; a = 22.0 x 10-6/°C] rods and a single solid steel [oy = 250 MPa; E = 200 GPa; a = 11.7x10-6/°C] rod. Bronze rods (1) each have diameters of d₁= 16 mm and lengths of L₁ = 3.1 m. Steel rod (2) has a length of L₂ = 4.2 m. (a) Calculate the diameter d2 required for steel rod (2) so that the deflection of joint B is zero for any change in temperature. (b) Using the value of d2 determined in part (a), determine the maximum temperature decrease that is allowable for this assembly if a factor of safety of 2.5 is specified for the normal stress in each rod. Since the temperature is decreasing, the answer should be negative. (1) (1) L₁ A C Answer: (a) d₂= (b) ΔT = i MI (2) B a L2 mm °℃
3. For the truss shown in the figure for this question, members AB and CD shown in bold each have a weight of 2 N. 4 m IC Establish the force in members BC, E I 3. CG, DE, and GH. Ans. FBC = 8 N (tension) FCG = 1.67 N (compression) FDE = 0 FGH = 6.67 N (compression) %3D 5 N 2N 7 N %3D %3D
Rigid bar ABC is supported by two identical solid bronze [oy = 331 MPa; E = 105 GPa; a = 22.0 x 10-6/°C] rods and a single solid steel [oy = 250 MPa; E = 200 GPa; a = 11.7x10-6/°C] rod. Bronze rods (1) each have diameters of d₁ = 25 mm and lengths of L₁ = 4.0 m. Steel rod (2) has a length of L2 = 5.4 m. (a) Calculate the diameter d₂ required for steel rod (2) so that the deflection of joint B is zero for any change in temperature. (b) Using the value of d2 determined in part (a), determine the maximum temperature decrease that is allowable for this assembly if a factor of safety of 1.6 is specified for the normal stress in each rod. Since the temperature is decreasing, the answer should be negative. (1) (1) L₁ A a (2) B a L2
Determine the forces in all bars of the truss shown in the given figure. Indicate tension or compression. Given: X=30 kN. XAN 60 LN The force in member AB (FAB) is The force in member BC (FBC) is The force in member AC (FAC) Is[ 6m kN. (Click to select) kN. (Click to select) kN (Click to select)
Problem 1: Determine the force in members DE,EI, JI, FI, and FE of the truss. 4 6 6→十44 +6-+ 6 4> 100 75 kN kN 75 kN 25 kN 25 kN E 3 F B K H 14 Dimensions in meters
Rigid bar ABC is supported by two identical solid bronze [oy = 331 MPa; E = 105 GPa; α = 22.0 x 10-6/°C] rods and a single solid steel [Oy = 250 MPa; E = 200 GPa; a = 11.7x10-6/°C] rod. Bronze rods (1) each have diameters of d₁= 15 mm and lengths of L₁ = 4.0 m. Steel rod (2) has a length of L₂ = 5.4 m. (a) Calculate the diameter d₂ required for steel rod (2) so that the deflection of joint B is zero for any change in temperature. (b) Using the value of d₂ determined in part (a), determine the maximum temperature decrease that is allowable for this assembly if a factor of safety of 2.3 is specified for the normal stress in each rod. Since the temperature is decreasing, the answer should be negative. (1) A a (2) B a L2 (1) C L₁
An aluminum alloy pipe AB [EAB = 12,000 ksi]with a cross-sectional area of AAB = 6.40 in.2 isconnected at flange B to a steel pipe [EBC =50,000 ksi] with a cross-sectional area of ABC= 7.60 in.2. The assembly is connected to rigidsupports at A and C.[LAB = 86 in.; LBC = 146 in.; PB = 177 kips ⇾]Determine the normal stresses in aluminumpipe AB and steel pipe BC.