R12-1. Sketch the intensity of the shear-stress distributionacting over the beam's cross-sectional area, and determinethe resultant shear force acting on the segment AB. Theshear acting at the section is V - 175 kN. Show thatINA - 0.3408(10) m.200 mm150 mm75 mm75 mmso mm

The given figure is shown below:

Answered: R12-1. Sketch the intensity of the…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

If the wide flange is subjected to a shear force of V = 30 kN, Draw the shear stress distribution in the beam and identify the maximum shear stress tmax-. Set w 200 mm. 300 mm A 20 mm 20 mm V 400 mm 20 mm W-
7-1. If the wide-flange beam is subjected to a shear of V = 20 kN, determine the shear stress on the web at A. Indicate the shear-stress components on a volume element located at this point. 200 mm 20 mm B 200 mm -20 mm 300 mm 20 mm
Problem 4: A high-strength steel wire CD is restraining an angle bracket ABC which supports a load P at A. Diameter of wire CD is 1/8 of an inch and the diameter of the pin at B is 1/8 of an inch. Determine the tensile stress in wire CD and the direct shear stress in the pin at B. 150 P=300lb. -5 in- dw ↓ 1 4 in. D View a-a of B
3) The plate shown is fixed connected along AB and held in the horizontal guides at its top and bottom, AD and BC. If its right side CD is given a uniform horizontal displacement of 4 mm, determine (a) the average normal strain along the diagonal AC, and (b) the shear strain at E relative to the x, y axes y. i= 340 mm j= 479 mm D k = 170 mm A k E j k B i 4тm
Problem 4: A high-strength steel wire CD is restraining an angle bracket ABC which supports a load P at A. Diameter of wire CD is 1/8 of an inch and the diameter of the pin at B is 1/8 of an inch. Determine the tensile stress in wire CD and the direct shear stress in the pin at B. dw C 4 in. dp B 15° 5 in: View a-a of B P = 200 lb.
calculate the location of the centroid, the second moments and product of area for the cross- section if; D = 67 mm, B = 41 mm & t = 2.41 mm A L Test beam A Strain gauge W (a) Unsymmetrical cantilever beam with weight applied at the free end and at the "shear centre", so that there is no torsion induced. Section A-A Strain gauge 1 Strain gauge 2 b Strain gauge 3 a B (b) Location of Huggenberger strain gauges From these, calculate the orientation and position of neutral axis for pure bending in the vertical plane (i.e. bending about a horizontal axis).
The rigid bar AD is supported by two steel wires of 1.5 mm diameter (E = 200 GPa) and a pinand bracket at D. Knowing that the wires were initially taut, determine the stress in each wirewhen a 1200 N load P is applied at D. What is the corresponding deflection of point D?
The symmetrical beam cross-section shown is loaded by a transverse shear force V 25 kip. Calculate the maximum transverse shear stress acting on the sec- tion. ΝΑ -+-1 in.|-- H V 6 in. 1 in. - 1 in.|-—_ 6 in.
The right angle bar is supported by a pin at B and a roller at C as shown in figure. The 30 mm diameter pin is in double shear. The shear stress in the pin is limited to 120 MPa. Neglect torsional effect. 400 mm BC The maximum safe value of Pis 30° P 480 mm kN. (Round off to one decimal place)
6–119. Determine the maximum allowable intensity w of the uniform distributed load that can be applied to the beam. Assume w passes through the centroid of the beam's cross-sectional area, and the beam is simply supported at A and B. The allowable bending stress is o allow = 165 MPa. %3D A 15° 6 m w(6 m) 15° 15 mm 100 mm 100 mm 10 mm 15 mm 15° 100 mm Probs. 6–118/119
The lap joint is fastened with four 3/4-in.-diameter rivets. The working stresses are 14 ksi for the rivets in shear and 18 ksi for the plates in bearing. a. TA Find the maximum safe axial load P that can be applied to the joint. Assume that the load is equally distributed among the rivets. b. Find the maximum average tensile stress in each plate. P 7 in. O 4 in. in. P
If the load P on the beam below causes the end C to be displaced 10mm downward, determine the normal strain in wires CE and BD. D 4 m A. B 3 m 2 m 2 m

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

R12-1. Sketch the intensity of the shear-stress distribution acting over the beam's cross-sectional area, and determine the resultant shear force acting on the segment AB. The shear acting at the section is V - 175 kN. Show that INA - 0.3408(10) m. 200 mm 150 mm 75 mm 75 mm so mm