Question Five A 50mm diameter solid bar is drilled axially and concentrically to a depth of 90 mm with a 20mm diameter hole. The bar is then loaded by a torque, which produces a maximum shear stress of 86 MN/m² in the bar. The total angle of twist is measured to be 0.65 degrees. Determine a) the applied torque b) the total length of the bar Take the Modulus of Rigidity as 75 GN/m2

Question Five A 50mm diameter solid bar is drilled axially and concentrically to a depth of 90 mm with a 20mm diameter hole. The bar is then loaded by a torque, which produces a maximum shear stress of 86 MN/m² in the bar. The total angle of twist is measured to be 0.65 degrees. Determine a) the applied torque b) the total length of the bar Take the Modulus of Rigidity as 75 GN/m2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A flange bolt coupling consists of 12-14mm diameter steel bolts on a bolt circle 320mm in diameter and 8-12mm diameter on a concentric bolt circle 260mm in diameter. What torque can be applied without exceeding a shearing stress of 60MPa in the bolts? B) Determine the number of 10mm steel bolts that must be used on the 320mm bolt circle of the coupling to increase the torque capacity by 6KN-m.
A solid steel bar with a circular cross-section has diameter 50 mm, length 1.5 m and shear modulus of 80 GPa. If the allowable shear stress is 48 MPa and the allowable angle of twist is 2.0 degrees, then what is the maximum permissible torque? State your answer in Nm to 1 decimal place.
EHide blocks Lets consider a solid circuiar shalt subjected to the torque loads as shown. Determine the minimum required diameter "Dif the shaft is made of a material having a shear modulus G 50 GPa, so that the maximum angle of twist at its end will not exceed -0.35° (calculated according to the positive sign convention). 100 N.m 500 N.m 200 N.m 300 mm 600 mm 600 mm Select one: O 40 mm O 70 mm O 80 mm O 60 mm O 50 mm
A flanged bolt coupling consists of eight d-mm diameter steel bolts on a bolt circle 262 mm in diameter, and four d-mm diameter steel bolts on a concentric bolt circle 200 mm in diameter. If the torque that can be applied is 7381 Nm without exceeding a shearing stress of 44.07 MPa in the bolts, what is the diameter of the bolts? Round off the final answer to two decimal places.
A flanged bolt coupling consists of eight d-mm diameter steel bolts on a bolt circle 261 mm in diameter, and four d-mm diameter steel bolts on a concentric bolt circle 194 mm in diameter. If the torque that can be applied is 8728 Nm without exceeding a shearing stress of 52.59 MPa in the bolts, what is the diameter of the bolts? Round off the final answer to two decimal places. Add vour answer
The Am1004-T61 magnesium tube is bonded to the A-36 steel rod. the allowable shear stresses for the magnesium and steel sre Tallow mg =45Mpa ve Tallow st=72MPa, respectively. The shear modulus of elasticity for Am1004-T61magnesium alloy is 18Gpa and for A-36 steel is 75Gpa. a)Determine the maximum allowable torque that can be applied at A. b)Find the corresponding angle of twist of end A.
The steel shaft is formed by attaching a hollow shaft to a solid shaft. Determine the maximum torque T (in Nm) that can be applied to the ends of the shaft without exceeding a shear stress of 70081031 Pa and angle of twist of 2.31°. Use G= 83000000000 Pafor the shaft, x = 2.5 m, and y = 1.71 m. Round off the final answer to two decimal places. T ... 100 mm 70 mm 70 mm T y
A 40-mm diameter hole is drilled 3-m deep into the steel shaft. When the first torque is removed at point B with 6000-N-m and the second torque is applied at point C with 2000-N-m, determine the following: a) The Maximum Shear Stress in the shaft. b) The angle of rotation of the free end of the shaft. 60 mm 40 mm B 2 m 3 m
Question 4. The shaft is made from a solid steel section AB and a tubular portion made of steel and having a brass core. If it is fixed to a rigid support at A, and a torque of T 50 kN.m is applied to it at C, determine the angle of twist that occurs at C and compute the maximum shear stress and maximum shear strain in the brass and steel. Take Gst 115 GPa, Gbr 56 GPa. 3 m %3D 2 m 100 mm 50 mm T= 50 kN. m
5) Find the maximum shear stress in each shaft for the following arrangement. Assume the diameter value of all shafts is same (50 mm) and material is steel (G-85 GPa) Dimensions in mm 40 500 Nm
SS mm 5.) Determine the thickness of a outside diameter of 100 mm hollow shaft having an if it is subjected to a maximum torque of 5403.58 N-m without exceeding sheaving stress of 60 MPa or a twist of 0.5 degree. meter length of shaft. G= 83,000 MPa. a per
A constant torque of 75 lb-in. is applied to the circular rod below, with a radius of 2 in. The shear modulus G = 3.5 x 106 psi. What is the angle of twist, p, at the end of the 6 foot long rod? 0.117 rad 0.056 rad 0.234 rad 0.314 rad T