Question 3: The figure below shows the outline of a shaping machine in which the driving crank OS rotates clockwise about the fixed centre 0 at 180 rev/min. The tool carrier R slides in horizontal guides and is connected to CD by the rod DR. For your specific Crank angle, determine the Kinematic quantities specified in the summary page. RAll dimensions in mm OS = 150 = 670 = 430 = 660 DC S'C DR S' 320 500

Question 3: The figure below shows the outline of a shaping machine in which the driving crank OS rotates clockwise about the fixed centre 0 at 180 rev/min. The tool carrier R slides in horizontal guides and is connected to CD by the rod DR. For your specific Crank angle, determine the Kinematic quantities specified in the summary page. RAll dimensions in mm OS = 150 = 670 = 430 = 660 DC S'C DR S' 320 500

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider the figure as shown below. O-XoYoZo is the reference frame and O-X₁Y₁Z₁ is the frame attached to the tool. Sketch the tool position after each intermediate position of the operation of the tool about the reference frame: roll π/2(rotate about Zo), pitch -T/2(rotate about Yo), yaw π/2(rotate about Xo). Please write the final rotation matrix expression. ZI,Zo XI,Xo Yı, Yo
Evaluate the 3-DOF wrist as shown in Figure 2, use the conventional method to determine 1. Linear velocity and 2. Angular velocity NOTE: for JOINT 3 ( 03 ) only Connected to robot arm Pitch Roll Yaw Figure 2: Wrist assembly The known position and orientation of the end of the arm point is. C, C2 [-C,S2C3 + S¼S3 -S;S2C3 – C1S3 C2C3 C¡S2S3 + S1C3 S4S2S3 + C,C3 -C2S3 01 S,C2 S2 1 °T3=°T¡'T2²T3
Crack AB of a slider crack mechanism shown in Figure 2 rotate at a constant speed of 300 rpm in clockwise direction. The connecting rod BC has a length of 1 m and incline at 45o to vertically positioned piston C. No angle or length for AB is given in the original question, thus I assume the angle is 70o because of the rough drawing I did here. Draw the displacement diagram of the mechanism shown in Figure 2 to scale. Use a vector diagram to determine the velocity of the piston C and connecting rod BC. Calculate the acceleration of piston C and the angular acceleration of connecting rod BC.
Sketch the 2D figure of cover using AutoCAD and mention all the dimensions 116 5R 90 Dia 12 holes Kid 8R 50 Bia 6R 8R 15R 2 holes 18 Dia 132 Cover
Figure out the 2D sketch of rocker using AutoCAD and mention all the dimensions. Colour the hatched lines which are inside the curve (red) 88 12R 2 holes 12 Dia 40 R 10RY 14R 80 100 34 R 89 120 15
Answer the following in the space provided. 39. Suppose the engine in a vehicle is delivering 550 lb-ft of torque at 5000 rpm, and the manual transmission is in 3rd gear with a gear ratio of 1.5:1. Calculate the transmission output speed and output torque. Transmission output speed %3D Transmission output torque =
A flange used to connect two pipes is shown in Figure Q3. Holes need to be drilled to fix it. Drilling should be done in two steps with each step 6 mm. Using absolute coordinate system and the parameters given in the table below, (i) Determine the coordinates of hole H=3 (ii) Determine the shortest distance between hole H=3 and the center (ii) Write a G code program for drilling hole H=3 only. CNC Drilling Operating Conditions Speed of the spindle 1670 RPM Feed rate of drilling 17 mm/minute Size of the drill bit 8 mm Rack number of drill bit 4 Distance kept between the drill bit and the work piece surface 2.5 mm The flange thickness 12 mm H=2 H=3 H=1 B=30° H=4 B A = 60°. angle = 0°. Center (0, 0) Radius 60 mm %3D
Problem Statement: A car drives on a circular track with radius 270 m. Initially, the displacement s=0 and the speed is 24 m/s. The car then begins to accelerate at At 0.3s (given in m/s? where s is in meters). After 3.4 seconds has passed, determine: (To get this answer you may need to use a table of integrals and/or a numerical equation solver.) The distance traveled: ûn The velocity vector: un The acceleration vector: Be sure to include units with your answers.
Question 1: The crank O1A of a mechanism as shown in figure below rotates uniformly at 955 rpm clockwise. Various links have following dimensions: OjA = 100 mm, AC = 700 mm, O3C = 200 mm, BD = 150 mm and O2D = 200 mm. Point B (Joint) is located on link AC as per figure. a) Make appropriate scale to draw position diagram using graphical method. b) Find the linear velocities (mm/sec) and angular velocities (rad/sec) for links O2D and BD and draw velocity diagram. What will be normal acceleration of Point B (Note: No need to draw Acceleration diagram) c) Identify total number of links and full joints (revolt joints) in the mechanism. 200 mm 200 mm A O2 O3 300 mm 400 mm
The general linkage configuration and terminology for an offset fourbar slider-crank linkage are shown in Figure below. The link lengths and the values of 02 and w2 are defined in. For the row(s) b and c, find the velocities of the pin joints A and B and the velocity of slip at the sliding joint using an analytical method. Draw the linkage to scale and label it before setting up the equations. Link 3 Offset 04 = 90° Link 2 02 Slider position d TABLE P6-2 Data for Problems 6-6 to 6-7† Row Link 2 Link 3 Offset 02 1.4 4 1. 45 10 2 6. -3 60 -12 3 8. -30 -15
Figure out the 2D sketch of housing using AutoCAD and mention all the dimensions. Colour the hatched lines which are inside the curve (red) 37 30 14 R 2 holes 72 Dia 12R 60R 30 R 24 10 R 15R Housing 60 R
Draw a displacement diagram with the following details: Maximum displacement of 60 mm 60 mm rise from 0 degree to 45 degree using simple harmonic motion 60 mm fall from 45 degree to 90 degree using simple harmonic motion Dwell from 90 degree to 120 degree 60 mm rise from 120 degree to 210 degree using uniform acceleration and retardation motion Dwell 60 degrees Return stroke using cycloidal motion Use 3 degree = 2 mm ratio Label the displacement diagram for every 30 degrees (20mm) in the x-axis Provide computations if needed (specially in creating cycloidal motion)