Please help me with this question its urgen QUESTION 2:2.1 A shaft is to transmit 190 kW at 180 rev/min. If the maximum torque transmitted is 50%more than the mean torque, the shear stress should not exceed 45 MPa nor an angle oftwist of greater than 1.2° per metre length. Determine the required diameter if:2.1.1 The shaft is solid2.1.2 The shaft is hollow with the ratio of inner to outer diameters of 3:5. Take modulus ofrigidity=80 GPa.2.2 A compound steel shaft is formed by attaching a solid and a hollow shaft as shown inbelow figure. The maximum allowable shear stress in the shaft should not exceed 70 MPaand the total angle of twist should not exceed 2.08°. If the length x is 2.28 m and thelength y is 1.69 m, calculate for a value of G-83 GPa:2.2.1 The magnitude of the allowable maximum torque2.2.2 The angle of twist of the hollow shaft.2.2.3 The stiffness of each shaft.100 mm70 mmC70 mmy

Answered: Image /qna-images/answer/7b67bf4f-e500-43ac-81e5-918f23268704.jpg

QUESTION 2: 2.1 A shaft is to transmit 190 kW at 180 rev/min. If the maximum torque transmitted is 50% more than the mean torque, the shear stress should not exceed 45 MPa nor an angle of twist of greater than 1.2° per metre length. Determine the required diameter if: 2.1.1 The shaft is solid 2.1.2 The shaft is hollow with the ratio of inner to outer diameters of 3:5. Take modulus of rigidity=80 GPa.

QUESTION 2: 2.1 A shaft is to transmit 190 kW at 180 rev/min. If the maximum torque transmitted is 50% more than the mean torque, the shear stress should not exceed 45 MPa nor an angle of twist of greater than 1.2° per metre length. Determine the required diameter if: 2.1.1 The shaft is solid 2.1.2 The shaft is hollow with the ratio of inner to outer diameters of 3:5. Take modulus of rigidity=80 GPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The dimensions of a stepped shaft are shown below. The maximum shear stress specification of the material is 67.1 MPa. Calculate the allowable torque for the shaft. r= 2.4 mm 12 mm 15 mm
A hollow steel shaft is stressed to 35 MPa by a torque of 200000Nm. Determine the outside diameter in mm if the inside diameter is 2/3 of the outside diameter both in mm.
An automobile engine develops a maximum torque of 162Nm. The low gear ratio of transmission is 2.75, while the back axle ratio is 4.25. The effective wheels radius is 0.325m and the co-efficient of friction between the tyre and the road surface is 0.6. If the permissible shear stress is 32373 X 104Pa. Determine the maximum shaft diameter. Assuming that the load is nearly torsional. What is maximum load permissible on each wheel?
A solid constant-diameter circular shaft is subjected to the torques of TA = 480 lb-ft, TB = 1060 lb-ft, Tc= 860 lb-ft, and Tp = 280 lb-ft, acting in the directions shown. The bearings shown allow the shaft to turn freely. (a) Plot a torque diagram showing the internal torque in segments (1), (2), and (3) of the shaft. Use the sign convention presented in %D Section 6.6. (b) If the allowable shear stress in the shaft is 5800 psi, what is the minimum acceptable diameter for the shaft? TB TA Tc (1) Tp (3) В C D Answer: (a) T1 = Ib-ft T2 = Ib-ft T3 = Ib-ft (b) d = in.
2. A Cast iron shaft transmits 30kW at 300 rpm. It carries a central load of 1000N and is simply supported between the bearings 3 meters apart. Determine the size of the shaft, if the allowable shear stress is 50MPa and the maximum tensile or compressive stress is not to exceed 60MPa.
3. The two identical shafts, 1 and 2, are built into supports at their left ends. Gears mounted on their right ends engage a third gear that is attached to shaft 3. Determine the torques in shafts 1 and 2 when the 500N -m torque is applied to shaft 3. 40 500 Nm 80 Dimensions in mm 4. A 4-ft-long tube with the cross section shown in the figure is made of aluminum. Find the torque that will cause a maximum shear stress of 10 000 psi. Use G = 4 x 106 psi for aluminum. +4 in. → 0.04 in. 0.08 in.´ 5. Two steel springs are arranged in series as shown. The upper spring has 36 turns of 100-mm- diameter wire on a mean radius of 350 mm. The lower spring consists of 24 turns of 75-mm diameter wire on a mean radius of 245 mm. If the ultimate shearing stress in either spring must not exceed 692 MPa, (a) compute the maximum value of P and total elongation using factor of safety equal to 1.5. (b) What is the equivalent spring constant? Use G = 83 GPa. 2 of 2 4 in. wwwww.-
Question 3 A hollow shaft for marine applications has outer and inner diameters of 400 mm and 200 mm respectively and transmits 8000 kW at 100 r/min. 3.1 Calculate the maximum shear stress in the hollow shaft. /4/ 3.2 Calculate the shear stress on the inner surface of the hollow shaft. /2/ an 3.3 Determine the maximum length of this shaft if the maximum shear stress as well angle of twist of 30 is not to be exceeded. (G = 80 GPa) /3/ 3.4 If this shaft is connected to a similar shaft, 1 m long, through a 10-bolt rigid flange coupling, determine the minimum standard bolt diameter if the pitch circle diameter of the coupling is pcd = 450 mm and the allowable shear stress in the bolts should not exceed 55 MPa. /3/ 3.5 Determine the equivalent torsional stiffness of the shaft assembly. /3/ [15]
(6) A solid shaft is used to transmit 75kW @ 550rpm. If the shaft design stress will not exceed 26N/mm2 , determine the diameter of the solid shaft.
1.A hollow steel shaft transmits 600 kW at 500 r.p.m. The maximum shear stress is 62.4 MPa. Find the outside and inside diameter of the shaft, if the outer diameter is twice of inside diameter, assuming that the maximum torque is 20% greater than the mean torque. 2. A motor car shaft consists of a steel tube 30 mm internal diameter and 4 mm thick. The engine develops 10 kW at 2000 r.p.m. Find the maximum shear stress in the tube when the power is transmitted through a 4 : 1 gearing. 3.A line shaft rotating at 200 r.p.m. is to transmit 20 kW. The allowable shear stress for the material ofthe shaft is 42 MPa. If the shaft carries a central load of 900 N and is simply supported between bearing 3 metre apart, determine the diameter of the shaft. The maximum tensile or compressive stress is not to exceed 56 MPa. 4.A cast gear wheel is driven by a pinion and transmits 100 kW at 375 r.p.m. The gear has 200 machine cut teeth having 20° pressure angle and is mounted at the centre of a 0.4 m…
À solid 0.96-in.diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Determine the shear stress magnitude in shaft (1). 10 Ib-A 50 Ib-ft 70 Ib-ft (1) (2) 30 Ib-f (3) 827 psi O 880 psi O 956 psi 691 psi O 739 psi
A shaft is used to transmit 67 kw at a speed of 2,281 rev/min. Using a maximum allowable shear stress of 57 MPa, find the shaft diameter in mm.
Determine the minimum diameter that can be used for a solid circular steel shaft which is limited to an allowable shear stress of 70 MPa and a maximum angle of twist of 1.5o (degrees) per meter length. Applied maximum torque is 25 KN-m and the overall shaft length is 1.25 meters. Shear modulus = G= 80 GPa Note: When using torsion stress formulas, you must convert the angle of twist from degrees to radians.