Question 1: a) Use Slope Deflection Method, determine the moment that each member exerts on the joints at B and D, then draw the moment diagram for each member of the frame. Assume the supports at A, C, and E are pins. El is constant. Also, draw the elastic curve for the deformed frame. 12 kN/m 10 kN D 4 m Wi kN/m 15 kN B 3 m 4 m

Question 1: a) Use Slope Deflection Method, determine the moment that each member exerts on the joints at B and D, then draw the moment diagram for each member of the frame. Assume the supports at A, C, and E are pins. El is constant. Also, draw the elastic curve for the deformed frame. 12 kN/m 10 kN D 4 m Wi kN/m 15 kN B 3 m 4 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

ASAP
/stemezcom Lec3 working stres For the beam shown below, determine the concrete and steel stresses at the locations of the maximum positive and negative moments, Use ſ'c = 25Mpa. The answers are MPa, MPa, MPa and MPa. 3okN/m 8m 1m 4-25mmØ- -Top bars -4-16mmØ 250 250 bottom bars 630 630
X Your answer is incorrect. The simply supported beam consists of a W21 x 44 structural steel wide-flange shape [E = 29,000 ksi; I = 843 in.4). Assume that the support at D can provide resistance either up or down. For a loading of w = 7.5 kips/ft, determine: (a) the beam deflection va at point A. (b) the beam deflection vc at point C. Assume LAB = 10 ft, LBC = 5 ft, LCD=5 ft, LDE= 6 ft. D LAB LBC LCD LDE Answers: (a) VA = 10.03 in. (b) vc = -1.197 in.
.The beam is subjected to the loads q0 and P, with the values added to the table below. Point C, where force P is applied, is located at L/2 from points A and B. Knowing, that cross section of the beam has moment on inertia equal to 232*106 mm4. The beam was modified to improve its performance and structural integrity roller support was placed at point B. For the system determine: a) Reaction forces using integration method b) Reaction forces using method of superposition;
Current Attempt in Progress The simply supported beam consists of a W21 x 44 structural steel wide-flange shape [E = 29,000 ksi; 1 = 843 in.4]. Assume that the support at D can provide resistance either up or down. For a loading of w = 5.4 kips/ft, determine: (a) the beam deflection VÀ at point A. (b) the beam deflection vc at point C. Assume LAB = 13 ft, LBc = 7 ft, LcD = 7 ft, Lde = 6 ft. W B Answers: (a) VA = (b) vc= LAB LBC D LCD in. in. LDE E X
The rigid bar AD is supported by two steel wires of in. diameter (E = 29 x 8 in. 106 psi) and a pin and bracket at A. Knowing that the wires were initially taut, determine (a) the additional tension in E 10 in. B each wire when a 220-lb load P is applied at D, (b) the corresponding deflection of point D. 12 in. 12 in. 12 in.
An angle bracket ABC is restrained by a high strength steel wire CD, and it supports a load P at A, as shown in figure. The strength properties of the wire and the shear pin at B are ou = 350 MPa (wire), and t=300 MPa (pin at B). If the wire and pin are to be sized to provide a factor of safety of the wire F.S = 3.3 and a factor of safety of the pin F.S = 3.5. What are the required diameters of the wire (to the nearest mm) and the pin (to the nearest mm)? dw D 90 mm 20° 100 mm View a-a of B P = 2 kN
Design the positive moment of the beam shown below, determine the number of 20mm diameter bars and the tension steel area, As. Assume the loads given are already factored. b=260mm d=420mm fe=21MPA fy=275MPA As = sq mm. n = 50KN 3m 20 KN/m
Q2) For the beam and loading shown, determine (a) the equation of the elastic curve for portion AB of the beam, (b) the slope at A, (c) the slope at B. A B
JC = For the beam and loading shown, determine (a) the deflection at C, PL 0 A P Bt² 2 EI (b) the slope at end 4. PL ↑P -L/3L/3L13 EI D
Your answer is incorrect. The simply supported beam consists of a W21 x 44 structural steel wide-flange shape [E = 29,000 ksi; I = 843 in.4). Assume that the support at D can provide resistance either up or down. For a loading of w = 4.8 kips/ft, determine: (a) the beam deflection Va at point A. (b) the beam deflection vc at point C. Assume LAB = 10 ft, LBc = 7 ft, LcD =7 ft, LDE = 4 ft. В C D |E LAB LBC LCD LDE Answers: (a) vA = 7.504 or 7.16 in. (b) vc = -0.814 or 6.56 in.
The simply supported beam consists of a W21x 44 structural steel wide-flange shape [E = 29,000 ksi; I = 843 in."]. Assume that the support at D can provide resistance either up or down. For a loading of w = 7.5 kips/ft, determine: (a) the beam deflection vA at point A. (b) the beam deflection vc at point C. Assume LAB = 11 ft, LBc = 7 ft, LcD= 7 ft, LDE = 7 ft. 11111111公彩 B. C LAB LBC LCD LDE Answers: (a) VA= in. -19.406, (b) vc 2.016 in.