Q4 a) Determine the wind speed at a height of 40m over surface terrain with a few trees, if the wind speed at a height of 10m is known to be 5 m/s. For your estimate use two different wind speed estimation methods. b) Using the same methods as part (a), determine the wind speed at 40m if the trees were all removed from the terrain.

Q4 a) Determine the wind speed at a height of 40m over surface terrain with a few trees, if the wind speed at a height of 10m is known to be 5 m/s. For your estimate use two different wind speed estimation methods. b) Using the same methods as part (a), determine the wind speed at 40m if the trees were all removed from the terrain.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.8P

See similar textbooks

Similar questions

MT NUIES ASK YOUR (a) Find a conversion factor to convert from miles per hour to kilometers por hour, mi/h x = km/h (b) Suppose the maximum highway speed is 70 mi/h, Use the conversion factor from part (a) to find the speed in kilometers per hour. km/h (c) Suppose the maximum highway speed has been raised to B5 mi/h in some places. In kilometers per hour, how much of an increase is this over the 70 mi/h limit? km/h
The left and right water edges of a river are 2.75m and 62.45m, respectively, from an initial reference point. Verticals are located at distances 11.25, 19.25 26.75, 34.45, 40.95, 46.95, and 54.45 m, respectively from the reference point. The corresponding depths of verticals are 5.00, 9.60, 9.80, 10.00, 10.40, 10.00, and 4.80m. Mean velocities in the verticals are 0.16, 0.60, 0.75, 0.92, 0.97, 0.98, and 0.65 m/s respectively. A. Determine the Total Discharge of the river. B. Determine the average velocity of the river flow.
1. For a set of experimental data of (x, y), i = 1,.,n, the theoretical analysis suggests that the data should follow a basic form of y = Axmexp(Bx2). (1) Assuming m is a pre-determined constant, how to transform the equation into a linear one? Give the relationships between the new and original coordinates. (2) Based on (1), how to calculate A and B from the slope and intercept of the linearization curve fitting?
Oxygen transfer medium is flowing over large semi-permeable membranes in a blood oxygenator. The membranes are rectangular with dimensions of 2 cm x 10 cm. The flow is along the 2 cm dimension. You can assume the viscosity and density of the medium is similar to that of blood plasma. a) If the velocity of the fluid is 100cm/min, is the flow laminar? b) What is the thickness of the boundary layer halfway across the membrane? c) What is the value of the average friction factor on the membrane? d) How much drag force is the membrane experiencing?
Find the velocity (m/s) at which test should be run in a wind tunnel on a model wing of 11 cm chord in order that RN. shall be the same as for a wing with a 1.16 m chord at 41.4 m/s. Air under standard conditions in both cases. Round-off answer to the nearest hundredths.
PROPAGATION OF ERROR You are tasked to supervise the design of 0.5MW wind turbine to be constructed in a Wind Farm in Pililla, Rizal. Suppose the design criteria are as follows: The air density as surveyed after 2 year period averaged at 1.225 kg / cubic meter. The sweeping diameter of the rotor blades is 125m, and the anemometer reading in the area amounts to 4.2m/s on a 2 year period of survey. What is the theoretical power output of the turbine assuming 100% efficiency of operation? Your answer must be in kW and in two decimal places with correct signs. In the previous problem, if the diameter measurement is off by 0.1m and the anemometer reading is also fluctuating by 0.05m/s and if the error measurement for theoretical power output must be limited to 3%, WHY OR WHY NOT should you accept the design? * Show complete solution in paper.
QUESTION 3 A 7.62 mm caliber bullet travel in two different medium of gas of helium and nitrogen at constant speed of 1,548 miles per hour. The properties of the gas are given in Table 1. Cp (kJ/kg.K) Cv (kJ/kg.K) Temperature (K) Pressure (kPa) Table 1 Helium 5.192 3.115 300 unknown Nitrogen 1.039 0.746 300 unknown a) Calculate the speed of sound in both medium (helium and nitrogen). b) Determine the March number of the bullet for both medium. c) Do you think that the shockwave occurs in this bullet travel for both medium of gas? Sketch your ideas of this bullet travel and the shock wave (if available).
If the velocity varies linearty with distance through this fluid nozzie (vertical nozzle), where the specific gravity of the fluid is S-0.46, what will be the pressure gradient, halfway through the nozzle? Assume steady and inviscid flow 2 m/s 50 cm 6 mis Select one a. 38465.20 O b. -57697.80 O e. 19232.60 O d. 9616.30 e. 76930.40
8 A car starts from rest, accelerates to 30 mph in 4 seconds, travels at 30 mph for 25 seconds, and decelerates to zero in 6 seconds. What's the total distance (in feet) traveled? Type your answer...
a test tank will be used to measure the drag of a scale model ship 0.8 m long. This model bears full resemblance to a 40 m long prototype ship that was designed to sail at a speed of 10 m / s. Evaluate: a) the speed of the modelb) the ratio between the drag forces of the model and the prototypec) the relationship between the powers needed to overcome the drag of the model and the prototype take the number of froud into account in your analysis.
2. Experimental measurements of relationship between velocity gradient and shear stress for different liquids are shown in the table given below. a) Plot the data on Excel and determine the fluid types. (Show your graph!) b) Which model do you use to describe the data? Specify the ranges of values for the coefficients. Velocity gradient Shear stress Fluid A Fluid B Fluid C 0.2 2.60 7.80 61.55 0.5 5.80 17.40 63.67 0.95 10.51 31.53 66.45 1.4 14.52 43.56 69.30 1.9 21.02 56.75 72.89 2.45 28.22 64.91 77.60 3.05 31.50 69.30 80.38 3.7 38.91 71.98 84.50 4.35 45.21 76.86 88.81 5.05 51.71 80.15 93.78
5. An elevator is accelerating downward at (where g = 9.81 in m/s³ ) when suddenly an object drops from its ceiling. If the distance between the floor and the ceiling of the elevator is d (in meters), how long will it take the object to hit the floor of the elevator? 7d A) t= | 2g 7d B) t= 3g 10d 3g C) t= 5d D) t= 2g boln