Q22. An object is shot straight up from 7 m above ground level, and returns to the ground after 2.3 s. If the effects of the air are neglected, what is the highest position it has reached (as measured from the ground)? Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point, and proper SI unit. Take g = 9.81 m/s². Your Answer: Answer units

Q22. An object is shot straight up from 7 m above ground level, and returns to the ground after 2.3 s. If the effects of the air are neglected, what is the highest position it has reached (as measured from the ground)? Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point, and proper SI unit. Take g = 9.81 m/s². Your Answer: Answer units

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.18P: The drag on an airplane wing in flight is known to be a function of the density of air (), the...

See similar textbooks

Similar questions

QUESTION 3 A 7.62 mm caliber bullet travel in two different medium of gas of helium and nitrogen at constant speed of 1,548 miles per hour. The properties of the gas are given in Table 1. Cp (kJ/kg.K) Cv (kJ/kg.K) Temperature (K) Pressure (kPa) Table 1 Helium 5.192 3.115 300 unknown Nitrogen 1.039 0.746 300 unknown a) Calculate the speed of sound in both medium (helium and nitrogen). b) Determine the March number of the bullet for both medium. c) Do you think that the shockwave occurs in this bullet travel for both medium of gas? Sketch your ideas of this bullet travel and the shock wave (if available).
Q6 The relationship between the velocity, u, of a construction vehicle (in km/h) and the distance, d (in metre), required to bring it to a complete stop is known to be of the form d = au² + bu + c, where a, b, and c are constants. Use the following data to determine the values of a, b, and c when: a) u 20 and d = 40 b) u = 55, and d = 206.25 c) u = 65 and d = 276.25 [Note: Use an appropriate standard engineering software such as MATLAB, CAS calculator, programmable calculator, Excel software]
A fixed amount of ideal gas is kept in a container of fixed volume. The absolute pressure P, in pascals, of the gas is plotted as a function of its temperature T, in degrees Celsius. Which of the following are properties of a best fit curve to the data? Select two answers. a. Having a positive slope b. Passing through the origin c. Having zero pressure at a certain negative temperature d. Approaching zero pressure as temperature approaches infinity
2. In class, we derived an expression for hR/RT for a gas that obeyed the Pressure Explicit Virial Expansion truncated after the third term. In class, we assumed that B and C were not functions of temperature. a. Please rework the derivation with B = B(T) and C = 0. b. Please continue the derivation under the assumption that B(T) = mT + b. Where m and b are the slope and y-intercept of a straight, respectively. %3D
The Simple Pendulum A H M Sketch a graph to show the predicted relationship. 2² H Task 8 In your group, discuss how to derive an equation to relate the initial pendulum height H to the bob's v 2 at its lowest point. Show the derivation of the equation. Then, again, use your theoretical equation to calculate the expected (theoretical) slope. Use g = 9.79 ± 0.05 m/s2 expected change in the bob's kinetic energy and the expected change in the bob's potential energy during this motion? released from rest and moving from a high position to its lowest position
What should be the surface tension of a liquid if its density, which is 1.44 g/cc, is the same as that of the calibrating liquid? The displacements of the liquid and the calibrating liquid inside the capillary tube are both 0.5 cm. The surface tension of the calibrating liquid is 29.4509 dynes/cm.
As we explained in earlier chapters, the air resistance to the motion of a vehicle is something important that engineers investigate. The drag force acting on a car is determined experimentally by placing the car in a wind tunnel. The air speed inside the tunnel is changed, and the drag force acting on the car is measured. For a given car, the experimental data generally is represented by a single coefficient that is called drag coefficient. It is defined by the following relationship: F, where air resistance for a car that has a listed C, = drag coefficient (unitless) measured drag force (N) drag coefficient of 0.4 and width of 190 cm and height of 145 cm. Vary the air speed in the range of 15 m/s
C Dynamic Analysis and Aeroelasticity SECTION B Answer TWO questions from this section ENG2012-N The moment of inertia of a helicopter's rotor is 320kg. m². The rotor starts from rest and at t = 0, the pilot begins by advancing the throttle so that the torque exerted on the rotor by the engine (in N.m) is modelled by as a function of time (in seconds) by T = 250t. a) How long does it take the rotor to turn ten revolutions? b) What is the rotor's angular velocity (in RPM) when it has turned ten revolutions?
The population of a community is known to increase at a rate proportional to the number of people present at time t. If an initial population P, has doubled in 7 years, how long will it take to triple? (Round your answer to one decimal place.) yr How long will it take to quadruple? (Round your answer to one decimal place.) yr еВook
Q1. The image below shows an example of "absolute dependent motion analysis", where the motions of two objects depend on each other, and the goal is to find the relations in their motions (i.e., in their positions, velocities, and accelerations). Please put the suggested steps of analysis in the correct order. VA A B VB Differentiate the entire equation with respect to time, and extract the relation in velocities. Repeat for acceleration if needed. Set up a coordinate (s) along the direction of motion from a fixed point (O) or a fixed datum line. Represent the positions of the objects respectively. In some cases intermediate objects need to be considered too and their positions need to be represented as well. Recognize the constant length(s) and find the depending geometric relations between the position variables.
An experiment is conducted on the surface of the planet Mars. Assume an isothermal atmosphere, where temperature To= 355 K, RMars= 189m2/s2.K, and the acceleration due to gravity is 3.5 m/s2. Estimate the altitude on Mars (in meters) where the pressure has dropped to 20 percent of its surface value. Numeric Response
One mole of a gas obeys the Ideal Gas Law PV = 20T, where P is pressure, V is volume, and T is temperature. If the temperature T of the gas is increasing at the rate of 5 °C/s and if, when the temperature is 80 °C, the pressure P is 10N/m? and is decreasing at the rate of 2- find the m2 . s rate of change of the volume V with respect to time.