Q22: Assuming the diameter of shaft (2) is 30-mm, determine the rotation angle (in degrees) of gearD with respect to gear B. Problem 3The gear system shown below has a motor supplying 38 kW at 340 rpm to gearA. Assume the following information:• Shaft (1) is a solid 45-mm-diameter aluminum [G= 22 GPa] shaft with a length of L₁ = 1230 mm.• Shaft (2) is a solid steel [G = 75 GPa] shaft with a length of L₂ = 700 mm.• Shafts (1) and (2) are connected at flange C, and the bearings shown permit free rotation of theshaft.• Assume NÃ=29 teeth and NB=71 teeth.NBA NABL₁(1)L2SESс(2)DTD

Answered: Image /qna-images/answer/38827624-bc90-4b1c-9103-0e93308f14d0.jpg

Answered: Q22: Assuming the diameter of shaft (2)…

Q22: Assuming the diameter of shaft (2) is 30-mm, determine the rotation angle (in degrees) of gear D with respect to gear B.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem 3 The gear system shown below has a motor supplying 38 kW at 340 rpm to gear A. Assume the following information: • Shaft (1) is a solid 45-mm-diameter aluminum [G= 22 GPa] shaft with a length of L₁ = 1230 mm. • Shaft (2) is a solid steel [G = 75 GPa] shaft with a length of L₂ = 700 mm. • Shafts (1) and (2) are connected at flange C, and the bearings shown permit free rotation of the shaft. • Assume NÃ=29 teeth and NB=71 teeth. NB A NA B L₁ (1) L2 SES с (2) D TD
The figure below shows the power transmitted through a gear drive to multiple output shafts. Gear A is mounted on an electric motor with a rotational speed of 600rpm. Gear A drives a simple gear train consisting in gears B, C, D, and E and transfers the input power to each gear to the shaft on which is mounted. The power delivered from shafts B, C, D, and E are: 8hp, 12hp, 5hp, and 5hp, respectively. For simplicity, all gears have a diametral pitch of 3 and the following numbers of teeth: NA=75, NB=15, NC=120, ND=15, NE=36. The torque on shaft D is most likely: 2015 lb in 105 lb in 250 lb in 630 lb in
The figure below shows the power transmitted through a gear drive to multiple output shafts. Gear A is mounted on an electric motor with a rotational speed of 600rpm. Gear A drives a simple gear train consisting in gears B, C, D, and E and transfers the input power to each gear to the shaft on which is mounted. The power delivered from shafts B, C, D, and E are: 8hp, 12hp, 5hp, and 5hp, respectively. For simplicity, all gears have a diametral pitch of 3 and the following numbers of teeth: NA=75, NB=15, NC=120, ND=15, NE=36. The expected rotational speed on shaft E is most likely: 375 rpm 600 rpm 1250 rpm 3000 rpm
The figure shows a schematic representation of a gear system. The gears are meshed with one another and can therefore not slip. The ring gear R is fixed, i.e. wR = 0. Gear A has an inner hub with radius rA(inner) = 0.3 m which is fixed to the rest of the gear, having a radius of FAlouter) = 0.8 m, and moves together as a unit. Gear A is in mesh with gear B which has a diameter of de = 1.5 m. Gear B has a clockwise angular velocity of wg = 2.1 rad/s. Determine the angular speed of gear A. B TA(outer R
Name: Referring to the given figure, spur gear A receives 5 hp at 650 rpm through its shaft and rotates clockwise. Gear B is an idler and gear C is the driven gear. The pressure angle o is 20° and the gear diameters: DA, DB, and DC are 6", 12", and 9" respectively. Determine: a. The torque each shaft must transmit, b. The tooth load for which each gear must be designed (Fr and Ft), C. The force applied to the idler shaft as a result of the gear tooth loads. C
You design a gearbox with a gear ratio of 5 (GR=5=TGB/Tm) to pull a load (FL) of 76 lbf using a motor and winch (rw=0.25 inches). What is the torque experienced by your motor when pulling the mass up at a constant speed in lbf ft? Note the units
(d) A motor drives the winch drum through a reduction gear with a gear tooth ratio of 0.1 as shown in Figure Q1(d). The friction torque at winch shaft is 15 Nm and at the motor shaft is 10 Nm. At the motor speed of 1500 rpm, the winch complete one rotational cycle in 11 s. (i) Calculate the equivalent moment of inertia of the drive referred to the motor shaft. (ii) Examine the motor torque if the gear and winch has efficiency of 90% and 98%, respectively. (iii) Find total power of the motor. Winch 0.2 m radius Motor Jo = 0.5 kgm? Gear Cable Jg = 0.15 kgm? at the motor speed Load 500 kg Figure Q1(d)
A spur gear set is shown in Figure Q6(a). The pinion 2 rotates at 750 revolutions/minute and transmits 1.8 kW to the driven gear 3. The teeth pressure angle is 20 degrees with a module m = 2.5 mm. 30 Теeth 3 - 20 Teeth Figure Q6(a) i). Determine the forces that act on gear 3 from the pinion. ii). Draw a free-body diagram of gear 3.
(a) Two involute gears of _pressure angle are in mesh. The number of teeth on pinion is 20 and the gear ratio is_. If the pitch expressed in module is 5 mm and the pitch line speed is_m/s, assuming addendum as standard and equal to one module, find : 1. The angle turned through by pinion when one pair of teeth is in mesh 2. The maximum velocity of sliding. D=30 G= 2 V=1.4m/sec
ASAP
Figure Q2 shows the top half of a compound Epicyclic gearset with input shaft I rotating at a constant speed of 700 rpm in clockwise direction and providing 12 kW input power. The Annulus wheel A2 is form a compound wheel with gear O and connected to an auxiliary gear N on shaft X. The Annulus A1 is rotating at a speed of 5,300 rpm in counter-clock clockwise direction. With this condition calculate the following:- (i) The speed and direction of output shaft O (No), shaft X (Nx) and gear ratio (n). (ii) If Annulus wheel A1 is locked calculate the speed and direction of output shaft O (No), shaft X (Nx) and gear ratio (n). (iii) The braking torque (Tb) (magnitude and direction) that must be applied to Annulus wheel A1 to hold it stationary, assuming gear transmission efficiency is 90%.
For the gear train illustrated in Figure, determine the output speed and direction of rotation if the input shaft rotates at 1490 rpm clockwise. Gears A to D have a module of 1.5 and gears E to H a module of 2. TA=20 teeth, TD=38 teeth, TE=18 teeth, TG=18 teeth, TH=30 teeth, dB=67.5mm, dC=27 mm and dF =56 mm.