Q1-Calculate the number of steps for a concrete stair with a space 290 x 310 cm to go up from ground level to first level at 296 cm including thickness of slab, if you know that: -The stair is U shape with first landing at level 148 cm & second landing at level 222 cm -There is a W.C under the landing of the stair. الدماء داللات دفاع اور انشاء کائی

Q1-Calculate the number of steps for a concrete stair with a space 290 x 310 cm to go up from ground level to first level at 296 cm including thickness of slab, if you know that: -The stair is U shape with first landing at level 148 cm & second landing at level 222 cm -There is a W.C under the landing of the stair. الدماء داللات دفاع اور انشاء کائی

Architectural Drafting and Design (MindTap Course List)

7th Edition

ISBN:9781285165738

Author:Alan Jefferis, David A. Madsen, David P. Madsen

Publisher:Alan Jefferis, David A. Madsen, David P. Madsen

Chapter16: Floor Plan Symbols

Section: Chapter Questions

Problem 16.18Q

See similar textbooks

Similar questions

Q5/ In the plan below there is a conventional L shape stair, the distance between slabs is 2.9m. find the followings: A/ Find the number of steps./6*18 B/ Find the riser height. C/ Find the tread width. 804 D/ If the provided area of stair is (2m*3m), check it the area is enough for installation the stair or not? Assume it the stair width is 90 cm. 36 36 36 36 72 72 175290 33.6 S 115 35 10 १९५० 188 HA 1.200 51-341 200 10 27 501-0 54 OPEN BED ROOM 11-7X140 25'-0" 144 144 184 288 +18 (818) LIVING 11-7 XIT-10.5" BATH 6-6*X4²-6² DRAWING 10-0"XII 0 8290 BATH KX5 BED ROOM 117 X14-0 KITCHEN 11-7 X8-0" 18 17 PORCH 13-1.5X20-4.5 36 36 36 33 72 72 18 27 bro 17490 9074 90 144- 14 TU IL 14
A teaching building has two floors in total, each floor is 3.3m high, and the height difference between indoor and outdoor is 500mm; the main stairs are ordinary double running parallel stairs and closed staircases. Please determine the dimensions of the stair and each part of the stairwell, and write out the calculation process. SUBJECT: : BUILDING A STRUCTUREAL DETAILING
Refer to Figure P2.4 for the floor plan. Calculatethe tributary areas for (a) floor beam B3, (b) floor beamB4, (c) girder G3, (d) girder G4, (e) edge column C3, and(f) corner column C4.
Determine the number of blocks needed to build the exterior stacked block wall from the footing to the top of the stacked block wall. Make sure to make calculations that will let you measure the below grade and exposed wall sections. (The stacked block unit is 8-inches x 8-inches x 16-inches; the decorative block has been eliminated and replaced with the stacked block used in the remainder of the structure.) Materials (per 100 s.f. face area Concrete Block Brick Materials 8 x 16 8x 18 5x 12 2.67 x 4 x 8 No. of Units 112.5 100 240 675 Mortar (Cu. Ft.) Face shell bedding 2.3 2.2 3.6 7.2 Mortar (Cu. FR.) Face shell and web bedding 3.2 3.0 2.5 7.2
Draw the following for a stair case: A longitudinal section in a stair that has 8 steps and a horizontal projection of 2.1m and a vertical projection of 1.2 m. The waist slab (flight) has a 20cm thickness. Each landing has a 20cm thickness and 1.3m length. Each landing is supported by a 20cm thick wall. Scale :1:20
Q5/ In the plan below there is a Spiral stair, the distance between slabs is 3m, there is the space for a staircase is 100 cm radius and the angle of rotation is 270°. find the followings: Find the number of steps. Find the riser height. Find the tread width. According to provided data, the stair can install or not?
Each floor of a 6-story residence building is 3.3m , the bay of staircase is 4.0m , the depth of staircase is 6.6m . The passageway is under the first-floor landing. The difference between floor elevation and ground elevation is 600mm , the landing beam's height is 350mm , wall thickness is 240mm, stairwell width is 60mm ( width of floor is at least 500~600mm) Question:- Design and calculation stairs of the residence building .(need answers asap please) The type of staircase wasn't mentioned
Read the question carefully ang give me the complete right solution with clear steps.
1/ For the plan and section of the wall shown below. Calculate quantities for each of the following construction works: 1- Excavation works for foundation. 2- All concrete works from foundation to the roof, take in consideration that there is a continuous tie beam. 3- Brick works (under & above the D.P.C level up to the parapet wall). Parapet Wall 0.60 oo Concrete tiles (0.9 x 0.9) m - 0.10 Isolated earth- 2 layers of asphalt and isolation- 0-15 The slab reinforced concrete (1:2:4) 4.00 0.15 Continuous tie Beam (1:2:4) 0.10 Earth filling- 0.08 Broken bricks- 0.05 The floor concrete (1:2:4) 0.03 Mosaic Tiles (0.25 x 0.25)m 0.10 0.16 G.L. 0-16 10:08 0.08. 0.20 0.08 r=2.00 9.60 Wz 5.50. Plan Section Width (m) Height (m) D 1 2 W1 2 1.5 W2 1.5 1.5
6'-6" 3 ASSUME CONCRETE = 150# / 173 5012 35/43 IS THE WALL STABLE?
You are to construct a Bodega with a rectangular floor plan using CHB (Concrete Hollow Blocks) as a material for walls. The floor area is 18 sq.m. The floor to ceiling height is 3.00m. The length of the North and South side are the same. The lengths of the North/South are twice the same as the East/West side. In the North wall, you have a standard door with dimensions of 0.90mx2.10m. In the South Wall, You have two windows; each has an area of 1sq.m each. How many pieces of CBH do you need in order to construct 4 walls of the bodega if a CBH has a dimension of Length – 40cm, Height – 20cm, Depth 10cm and 15 cm.? If 1 pc, CBH is Php. 15.00 How much do you need to spend to construct 4 walls of the bodega with a 10% contingency fee?
Problem 01. Analyze the building frame shown using Portal Method.