Q.4. A single-phase half-wave-controlled converter is operated from a 120V, 50HZ supply. Load resistance R = 10N. If the average output voltage is 25% of the maximum possible average output voltage, determine: (a) Firing angle (b) RMS and average output currents (c) Average and RMS SCR currents. Also draw the waveforms. (3)

Q.4. A single-phase half-wave-controlled converter is operated from a 120V, 50HZ supply. Load resistance R = 10N. If the average output voltage is 25% of the maximum possible average output voltage, determine: (a) Firing angle (b) RMS and average output currents (c) Average and RMS SCR currents. Also draw the waveforms. (3)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A thyristor half-wave controlled converter has a supply voltage of 240V at 50Hz and a load resistance of 100 ohms. What are the average values of load voltage and current when firing delay angle is; 1. 140 degrees. 2. 30 degrees.
A 3-phase half wave controlled AC to DC converter is supplied from a 250V, supply. Assume the thyristor voltage drop to be 1.6V and the load current to be continuous. Evaluate the mean output voltage when firing angle is varied at 45(degree) , 60(degree) and 90(degree)
Input voltage of a boost converter 80 V, output voltage 140 V and switchingits frequency is 20 kHz. The converter efficiency is known to be 95%.a) Continuous conduction (current) in operation when the load resistance changes between 14 - 20ohmThe lowest inductance (L) value and output that should be used to maintain the operation.the peak-to-peak value of the voltage ripple should be used to be 2% of the output voltage.Calculate the capacitor's capacity (C).
Drive the expression for the average output voltage of a single phase full converter and draw the waveform of output voltage. please explain in details
A fully controlled, single-phase bridge rectifier is powered from an ideal 220V, 50Hz source. The rectifier is triggered with a trigger angle of 60 degrees and provides a smooth current of 50A to the load at the output. According to this: a) Draw the waveform of the output voltage in scale and calculate the average value of the output voltage. Combine the average voltage signal with the output voltage wave signal. Show on the same figure. b) Draw the waveforms of the thyristor currents, the gap diode current and the current drawn from the source in scale. c) Calculate the value of the filter inductance used at the output when the ripple in the load current is 3A. (Do the operations by showing the output voltage shapes and areas on the figure. The answers should be in the system and order in the solved examples.)
In a single-phase half-wave ac-dc converter, the average value of the load current is 1.78 A. If the converter is operated from a 240 V, 50 Hz supply and if the average value of the output voltage is 27% of the maximum possible value, calculate the following, assume the load to be resistive. (a) Load resistance (b) Firing angle (c) Average output voltage (d) The rms load voltage (e) The rms load current (f) DC power (g) AC power (h) Rectifier efficiency (i) Form factor (j) Ripple factor
The average (DC) value of a half-wave rectified voltage with a peak value of 200 V is: a. 63.7 V b. 127.3 V c. d. OV 141 V 2. Voltage regulation is determined by: a. load current b. Zener current and load current c. changes in load resistance and output voltage d. changes in no-load voltage and full-load voltage When a 60-Hz sinusoidal voltage is applied to the input of a full-wave rectifier, the output frequency is: a. 120 Hz b. 60 Hz c. 240 Hz d. 0 Hz
what is the difference of MOSFET and Diode in Boost Converter. Can you also sight an example?
3. A single phase half-wave converter is operated from 230V, 50 Hz source and the load R=1202. For a firing angle of 30°, determine: (a) Rectification efficiency (b) Form factor (c) Voltage ripple factor.
DERIVE AVERAGE OUTPUT VOLTAGE EQUATIONS FOR 3-PHASE SEMI CONVERTERS.
Q: Design a regulated power supply with an input voltage of 220 V (RMS value) and output regulated voltage of 12V. Use Zener diode as regulating device. Provide the following for your design: a. Block diagram b. Schematic diagram c. Manual computation per section with corresponding output waveform. d. Show comparison of the input and output signal waveforms.
Q2: A buck converter has an input voltage of 50V and output of 25V. The switching frequency is 10KHZ. The power output is 125w. Determine (a)the duty cycle, (b) the value of L to limit the peak inductor current to 6.25A, (c) the value of capacitance to limit the output voltage ripple factor to 0.5 %.