Q.2 A bipolar PWM single-phase full-bridge DC/AC inverter has Va = 300V, ma = 1.0, andftri = 2550 Hz. The inverter is used to feed RL load with R = 100 and L = 15mH atfundamental frequency is 50 Hz. Determine:a) The rms value of the fundamental frequency load voltage and current?b) The highest current harmonic (one harmonic)?c) An additional inductor to be added so that the highest current harmonic is 10% of its inpart b?

Data given is DC input voltage, Vd=300V Index, ma=1.0 Triggering frequency, ftri=2550 Hz…

Q.2 A bipolar PWM single-phase full-bridge DC/AC inverter has Va feri = 2550 Hz. The inverter is used to feed RL load with R = fundamental frequency is 50 Hz. Determine: = 300V, ma = 1.0, and 102 and L = 15mH at a) The rms value of the fundamental frequency load voltage and current? b) The highest current harmonic (one harmonic)? c) An additional inductor to be added so that the highest current harmonic is 10% of its in part b?

Q.2 A bipolar PWM single-phase full-bridge DC/AC inverter has Va feri = 2550 Hz. The inverter is used to feed RL load with R = fundamental frequency is 50 Hz. Determine: = 300V, ma = 1.0, and 102 and L = 15mH at a) The rms value of the fundamental frequency load voltage and current? b) The highest current harmonic (one harmonic)? c) An additional inductor to be added so that the highest current harmonic is 10% of its in part b?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A square wave output single phase bridge inverter supplies an 80 resistor with 40mH inductance load. Load fundamental rms voltage is 135V at 60HZ.Calculate: (a) Voltage of the dc supply. (b) rms value of load voltage, load current and third harmonic voltage. (c) Load power.
4) A single phase full bridge inverter will be used to generate 50 Hz square wave voltage. Inverter the input voltage is 400 V and the load consists of inductance and resistance connected in series. (R=10Ω, L=31.83 mH) a) Draw the circuit b) Plot the load current, showing the load voltage and semiconductor currents. c) Load voltage is effective calculate the value d) Calculate the effective value of the main harmonic of the load current. e) Calculate the average load current. f) Find the THD of the load voltage
QUESTION SEVEN A single-phase bridge inverter is fed from 230 V dc. In the output voltage wave, only fundamental component of voltage is considered. Determine the rms current ratings of an SCR and the diode of the bridge for the following types of loads: (a) R = 20 (b) wL = 29. Find also the repetitive peak voltage that may appear across a thyristor in parts (a) and (b).
2. A single-phase half--bridge inverter is connected to a 600V d.c. source. A series connected R-L load has R = 60 ohm, L= 70mH. The inverter frequency is 60 Hz. Determine the values of the rms load current, the load power and the total harmonic distortion factor, up to the 11th harmonic.
For single phase voltage source bridge inverter 1. Draw the circuit. 2 With R 100. I SOmH frequency is 50 Hz and supply voltage is 380V. With square wave output draw the waveforms of output voltage v1 and load current i . 3 Calculate the RMS value of output voltage and mean output power.
Q2 (a) Figure Q2(a) shows a single-phase full-bridge square-wave voltage source inverter has resistor (R) and inductor (L) load of 10 Q and 5 mH respectively connected in series. The inverter output frequency is 50 Hz. The transistor switching scheme is complementary bipolar. (i) Draw the output voltage and current waveforms. (ii) Obtain an expression of the rms output voltage at the fundamental frequency. (iii) If the fundamental AC output voltage is 220 V, find the required DC input voltage for the inverter. (iv) Find the instantaneos load current by considering until the 9th harmonics number. (v) Calculate the total harmonics distortion (THD) of the load current. Use only the first three odd harmonics. (vi) Sketch the harmonics spectrum for output current. (vii) Show the displacement angle a, if 5th harmonic is to be eliminated.
3. A single-phase to single-phase cycloconverter "bridge type" with input voltage and frequency 150V and 50Hz. respectively. The output frequency is 10Hz and the firing angle equal to 45°. The load is resistance with the value of 1002 in series with reactive inductance of the value of 20mH. Assume the extinction angle equal 180°. a. Draw the waveforms output voltage, output current, source current, the thyristors currents (iT, IT, IT and in) b. Calculate the rms of output voltage. c. The rms current of each thyristor. d. The input power factor
iv. For six-phase half-wave rectifier circuit, the preferred circuit from the point of harmonics reduction in the supply currents is: (a) Simple six-phase half-wave circuit. (b)Double-star six-phase half-wave circuit. (c) Six-phase fork connection circuit. v. The DC supply of single phase bridge inverter is 350V. For quasi-square wave output voltage with a 70 percent ON time and frequency is 50HZ, the RMS value of output voltage is: (a) 292.8V (b) 220.5V (c) 250.6V
Design a series inverter circuit for operation in the frequency range 50Hz to 90 Hz. The load resistance may vary from 20 Ohm to 80 Ohm. :Thepeak load current is limited to 4 A and the supply voltage is 120 V
Q1- For single phase voltage source bridge inverter: 1- Draw the circuit. 2- With R=102 , L=50mH, frequency is 50 Hz , supply voltage is 450V and quasi-square wave output and a 50 percent on time, draw the waveforms of output voltage (VL.) and load current (iL) when I=25.05A , Io= -9.217A. 3- Calculate the RMS value of output voltage and mean output power.
In a single phase VSI bridge Inverter, the load current is Io =200 sin(wt-45°)mA. The d.c. supply voltage is 220 V. What is the power drawn from the supply ?
4. A DC link inverter has an AC rms line input of 600 V, 50HZ. The inverter load is a balanced star connection of 1950 resistors. Determine load current and power for a converter firing angle delay of a) Determine load current, voltage and power for a converter firing angle delay of 12.5 degrees. b) Determine load current, voltage and power for a converter firing angle delay of 62 degrees.