Q.1) Replace the given force system by a resultant force system acting at point A. Then replace the resultant force system by the simplest resultant (a single force) and find x and y intercepts of its line of action from point A.

Q.1) Replace the given force system by a resultant force system acting at point A. Then replace the resultant force system by the simplest resultant (a single force) and find x and y intercepts of its line of action from point A.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.6P: Find the internal force systems acting on sections 1 and 2.

See similar textbooks

Related questions

Q: 3. For the loaded beam shown below, solve for the reactions at point A (a roller) and point B (a pin…

Q: Vectors represent magnitude and direction. We can solve for either: • The magnitude & direction of…

A: Given:To find:Magnitudes of E and F vectors.

Q: Find the force required to hold the plug in place. The water discharges freely into the atmosphere…

A: water velocity v=3m/sentry diameter D=0.25mplung diameter d=0.2mto find the force required to hold…

Q: Solving dynamics problems in steps: 1. Collect data and assumptions 2. Desired result? 3. Make…

Q: PROB: 1 BOLT CONNECTION DESIGN DETERMINE THE MAXIMUM PORCE THAT CAN BE OSTAINED FOR THE BOLTED…

A: Since you have posted multiple questions, we will provide the solution only to the first question as…

Q: From the figure as shown, determine the stress in psi at the top surface of the second cylinder.…

Q: 1) Bar A has a cross-sectional area of 2 in² and its modulus of elasticity is 10 x 10° psi. Bar B ha…

A: The area of bar A is The modulus of elasticity of A is The uniformly distributed load in bar A and B…

Q: Link 4 moves to the right with constant velocity of 75 ft/s. Using the graphical method, find VB,…

Q: Consider the residential heating, ventilation, and air conditioning (HVAC) system at right. A blower…

A: Given:To find:

Q: In a piston-cylinder system, there is 3 kg of refrigerant-134a initially at 1.2 MPa and 50°C. The…

A: The mass of refrigerant is .The initial pressure of refrigerant is .The initial temperature of the…

Q: A ball of mass m is connected to a rod of length L and swings around the axis O. At some instant,…

A: Given:To find:The tension in the rod andThe rate at which the speed of mass is increasing.

Q: Analytically determine the linear displacement of the piston in the compressor linkage shown in…

Q: The assembly consists of two 12-mm-diameter A992 steel rods AB and CD, a 20-mm-diameter 6061-T6…

A: To determine:The displacement of point Fgiven:The diameter of rods AB and CD is The diameter of rod…

Q: A clockwise couple M = 4.6 N·m is resisted by the shaft of the electric motor. (Figure 1) Figure 150…

A: The moment applied is

Q: a. Inlet, constant area test section with no diffuser b. Inlet, constant area test section with a…

Q: 7. Sketch within a cubic unit cell the following planes (a) (077) (e) (TIT) (b) (112) (f) (122) (g)…

A: Given: Sketch within a cubic unit cell the given planes:

Q: What is the angle of the slope?

A: m = 3000 kg

Q: The mechanical system shown in figure is driven by the applied force fa(t). When x1 = x2 = x3 = 0,…

A: Given:To find:Draw the free body diagrams and write the equations of motion.

Q: Question-3 The following illustration shows the construction parts of the disc brake. From the…

Q: The A-frame is being hoisted into an upright position by the vertical force of F = 40 lb. (Figure 1)…

A: The graphical illustration of the trigonometrical relation of Force F with the axis y' is shown…

Q: For all the following problems, 5. a) b) You need to show at least 3 iterations calculated manually…

Q: The temperature at the beginning of the compression process of an air-standard Otto cycle with a…

Q: (Determination of Pi terms) The flowrate, Q, in an open canal or channel can be measured by placing…

Q: 7.- A block of mass 20 kg is pushed upwards, along an inclined plane, with a horizontal force F of…

A: Given Data:A block of mass, m=200 kgHorizontal force, F=200NCoefficient of kinetic friction, v= 0,…

Q: A piston, with diameter D, is balanced in equilibrium within a cylinder containing water as shown.…

Q: Problem 01.013 - Probability of fatigue failure - DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTS A…

A: Number of specimen=69To determine:Number of specimen are predicated to fail at less than 115…

Q: List 2 double-rocker mechanisms that are used in industry. Justify why each mechanism belongs in the…

A: The two double-rocker mechanisms used in industry are as follows:1. Bell Crank Lever Mechanism:…

Q: A rain gutter is to be made of aluminum sheets that are 16 inches wide by turning up the edges 90°.…

A: From the given diagram of the main gutter,base = 16-2xheight = xThe Area is given as,Area =…

Q: Determine the distance d for placement of the laod P for equilibrium of the smooth bar when it is…

Q: Summarize how at least two reference materials relate to the basic scientific principles of flying a…

A: Reference material - 1:Authors: Laura Katchmark, Elisabeth McCabe, Kristen Matthews, and Michele…

Q: An electric resistance heating element with a length of 60 cm and a power rating of 1000 W, having a…

A: To determine:(a) time required for the heater to elevate water temperature to 70°C(b) Minimum work…

Q: 3. As a robotic engineer, your boss needs you to move the gripper on the UGV to the target object.…

A: Given the transformation matrices:Tsd : Transformation from sensor frame {d} to the fixed frame…

Q: A cantilever steel beam with the triangular cross section is loaded with the concentrated force as…

Q: ▼ Part C - Finding the spring constant As shown, Spring 3, which has an unknown spring constant k3,…

Q: Pipe AB has a diameter of 40 mm. Water flows through it at a rate of 0.017 m³/s. The pipe and water…

A: First we will apply Bernoulli theorem and then apply static equilibrium to get the force.

Q: The resulting stress distribution-along section AB for the bar is shown Figure 1 of 1 From this…

Q: A pipe made of stainless steel (k = 45 W / m*K) with an internal diameter of 5 cm and an outer…

Q: Determine the resultant force stress produces on top flange A and bottom flange B then compute…

A: The moment applied is

Q: In carbon steels, what is “pearlite”? In your explanation, describe both its composition and…

A: In carbon steels, what is “pearlite”? In your explanation, describe both its composition and…

Q: 16-87. If rod CD is rotating with an angular velocity wcD = 4 rad/s, determine the angular…

Q: Two kilograms of air within a piston-cylinder assembly execute a Carnot power cycle with maximum and…

A: For the Carnot power cycle, following data are provided:Heat input to the cycle is 60 kJ.It is…

Q: Given a Brayton cycle, with a pressure ratio equivalent to 12, as shown in the figure, determine its…

Q: Circuit Design - aircraft system application Draw the circuit of the flap and aileron actuation…

A: Ailerons:An aileron is used to control the roll of an aircraft. They are installed on the trailing…

Q: 5. The hoisting drum of diameter d = 20 cm rotates with a constant angular velocity of 4 rad/s and…

A: Write expression for velocity of rope at drum perimeter.Here d is diameter of drum and is angular…

Q: The element in the image has a horizontal force of 20 N and a vertical force of 25 N. The element…

Q: The rotor of a gas turbine is spinning at a speed of 6,300 rpm when the turbine is deactivated. It…

A: Rotor initial speed Ni = 6300 rpm Rotor final speed Nf = 0 rpm ( rotor reaches rest )Time taken t =…

Q: Identify the basic drawing, using the cartesian coordinates ( Absolute and Incremental ) write the…

A: Given:To find:Write the absolute as well as the incremental cartesian coordinates of each point.

Q: The 0.1-1b projectile A is subjected to a drag force of magnitude kv², where the constant k = 0.002…

A: The magnitude of drag force is The weight of projectile is .The constant value is .The velocity is…

Q: At a point in a flowing fluid, the shear stress is 3x10-4 psi and the velocity gradient is 1 s-1.…

Q: Consider the thermocouple properties you found in the question "Temperature of a thermocouple (1/3)"…

A: To Find:the maximum temperature.Given:The room temperature is

Question

Q.1) Replace the given force system by a resultant force system acting at point A.
Then replace the resultant force system by the simplest resultant (a single
force) and find x and y intercepts of its line of action from point A.
60 lb
15"
10"
y
90 lb
A
9"
B -DE
120 lb-in.
12"
X G
12"
70 lb
10"
F
80 lb

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Calculate the Reaction Force and Moment

VIEW

Step 2: Calculate x and y intercepts

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Find the internal force systems acting on sections 1 and 2.
Q.4) A moment and four forces are applied to a two-dimensional frame as shown in figure below. Replace the given force system by a resultant force system acting at point A. Then replace the resultant force system by the simplest resultant and find x and y intercepts of its line of action. 50 lb C 18 in. 75 lb 12 in. B 10 in. E 100 in. lb 80 lb -14 in. -16 in.-16 in.- 90 lb
Q.6) Three forces are applied to bracket as shown in figure below. Replace the given force system by a resultant force system acting at point O. Then replace the resultant force system by the simplest resultant and locate its line of action as it passes through the y-z plane. 75 mm 1000 N 45° 50 mm 50 mm 1200 N 30 700 N 60° 100 mm 100 mm E(150 mm, -50 mm, 100 mm)
Q.5) Three forces are applied to bracket as shown in figure below. Replace the given force system by a resultant force system acting at point O. Then replace the resultant force system by the simplest resultant and locate its line of action as it passes through the y-z plane. y 800 N -ve z 70 mm 40 mm C 40 mm 120 mm Z 245° - X 1000 N 600N 60° D E(150 mm, -50 mm, 100 mm) 110 mm B/ y 1 45° 30° X
2. Determine the following: a) Magnitude of the projected component of along the line of action of F2 b) Angle 0 between the two cables attached to the pipe. F, = MN Ib 120 60° F, = SN Ib 1.5 m 3. The guy wires are used to support the telephone pole. Represent the force in each wire in Cartesian vector form. Neglect the diameter of the pole F= MNN F: = FN N 4 m 2 m D. 4 m 3 m y
Determine the magnitude of the resultant of the system of concurrent forces having the following magnitudes and passing through the origin and the indicated points: P=520 lb (+8,-6,+5), T=270 lb (-3,-4, +10), F=280 lb (+5,-3,-6). a.) 273.272 lb b.) 476.065 lb c.) 466.966 lb d.) 720.675 lb e.) None of the above
Q. 5 Find the resultant and its location w. r. t. point A for the force system given in the figure below- 50N 3 m 20 N 4 m 30N
Reduce the parallel force system shown in the figure to a single resultant force. Which of the following is 40 kN 48 kN 32 kN 72 kN the x coordinate of this 64 kN resultant force? 56 kN 2.4 3.6 2.8 Lutfen birini seçin a. 2.92 b. 6.33 C-2.92 d. -6.33 e. Hiçbiri
Replace the force system shown in figure, with a single resultant force. Determine the distance where its line of action intersects the leg AB measured from point A. 3 ft 190 lb 6 ft 450 lb-ft 75 lb 4 ft 250
Replace the force system by a single force resultant and specify its point of application, measured along the x axis from point P. Given: Fj = 125 N a = 1 m F2 = 350 N b = 3 m F2 F3 = 850 N c = 1.5 m d = 2 m a 1) Find FCR) = N. (+ Point up point down] 2) find distance bet ween FrR) and P
Q3b. Force vectors F1 and F2 act on body P with the resultant force vector R. The resultant force R= 350 N and the angle between R and the x-axis is of 35°. If F1 = 180 N and the angle between F1 and the x-axis is 72º, determine the angle between F2 and the x-axis. Assume coplanar vector forces and give your answer in degrees to two decimal places. F1 R F2 Body, P Answer:
Q2. Find the resultant ( R) of the force system shown in the figure. Show its position with - respect - to point C. Also show where it cuts the x- axis. 400 N 300N 3 m 5 m 2500 N-m 45 600N Lut