Q: The soil element with known stress conditions is shown in following figure. (i) construct Mohr's circle for the soil element and determine (ii) stress condition of the plane AC (use double angel method); (iii) major and minor principal stresses; (iv) the angle between major principal plane and the plane "AD"; (v) maximum shear stress. Provide your answer up to one decimal point. [use graph paper to draw Mohr's circle] 6 kN/m²

Q: The soil element with known stress conditions is shown in following figure. (i) construct Mohr's circle for the soil element and determine (ii) stress condition of the plane AC (use double angel method); (iii) major and minor principal stresses; (iv) the angle between major principal plane and the plane "AD"; (v) maximum shear stress. Provide your answer up to one decimal point. [use graph paper to draw Mohr's circle] 6 kN/m²

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Given a stress state of ø, = -4 MPa, øy = 12 MPa, ty = 7 MPa ccw 1) Draw a properly oriented stress element illustrating this state of stress 2) Using Mohr's circle, find the principal stresses and directions, and show these on a stress element correctly aligned with respect to the xy coordinates. Draw another stress element to show zi and 72, find the corresponding normal stresses, and label the drawing completely. 3) Use the plane-stress transformation equations to validate your answers in part 2
(b) Mohr's circle, invented by Christian Otto Mohr, is a graphical representation of the transformation law for the stress system. Use Mohr's circle to determine the stresses on an element inclined at 30° clockwise to the state of plane stress system as shown in Figure 1 and show the corresponding stress elements. Q2 (a) It is important im 80 MPa 50 MPa Ľ 50 MPa Figure 1 80 MPa 25 MPa
The state of stress at a point on a thin plate is as shown in the left side of the Figure below. Determine the state of stress (ox, oy, txy) represented on the element oriented as shown on the right. 120 Sigma_x^prime (MPa) 200 Sigma_y^prime (MPa) 60 Tau_xy^prime (MPa) 30 Alpha (degrees) O x' Oy Txy' Txy Ox
1. Given a combination of stresses on an element shown in the figure, (a) draw a Mohr's circle representing the complete state of stress of the element, i.e. show prinicpal stresses (01,02), maximum shear stresses (Tmax), principal direction (0p), original orientation, and original stresses (Ox, Oy, Txy). (b) draw three-dimensional Mohr's circles showing the three principal stresses and absolute maximum shear stress. Oy = -50 MPa Txy 20 MPa Ox = -150 MPa
Q2 The state of stress at a point of an elastic solid is given in the x-yz coordinates by: (a) Using the matrix transformation law, determine the state of stress at the same point for an element rotated about the x-axis 60° clockwise from its original position;(b) Calculate the stress invariants and write the characteristic equation for the originalstate of stress;(c) Calculate the deviatoric invariants for the original state of stress;(d) Calculate the principal stresses and the absolute maximum shear stress at the point;(e) What are the stress invariants and the characteristic equation for the transformed state of stress.
The internal loadings at a section of the beam in (Eigure 1) are shown Figure 20 mm 100 mm 200 mm 20 mm 10 kNm 20 mm 10/12 60 kN 80 KN 500 N-m Determine the in-plane principal stresses at point C. Also compute the maximum in-plane shear stress at this point Express your answers, separated by commas, to three significant figures. VAZ Ivec 4 d Submit Provide Feedback T Wha Bequest Answer ? MPA, MPA, MPA
A round solid bar has a diameter of 30mm. A tensile force of 120kN is applied at the centroid of area . A) Calculate the stress in the bar and sketch the stress distribution through its thickness along the centre line[ANS : 170 MPa] B) The force in Q1 is re-applied to the same round solid bar but 5mm above the centroid of area. Calculate the stress in the bar and sketch the stress distribution through its thickness along the centre line[ANS:+396, -56 MPa] HOW to answer part two I did not get the answer !!
Pressure vessels are very common in many industries. The purpose of this exercise is to examine how stresses evolve within the walls of a pressure vessel as a function of position within the wall and wall thickness. Recall the thick-walled cylinder solution developed in class. Re-write the solution to the case of a thick-walled cylinder with inner radius a, outer radius b, internal pressure p₁, and external pressure, p2. Orr = 000 = + a²p₁-b²p2 (P2₂ - P₁)a²b² 1 (b²-a²) (6²-a²) ²¹ a²p₁b²p2 (b²-a²) 1 axis (P2 - P₁)a²b² 1 (b²-a²) r² (a) Draw a diagram showing the evolution of orr and σ00 from a to b when a/b=0.5 and P2 = 0. (b) Make the assumption that p₂ = 0, a + b ≈ 2r, ba≈t, and a b≈r to derive the expression for orr and one for a thin-walled pressure vessel. For a sanity check, your solution should be arr 0 and σ00 = pir/t. = (c) Now consider the classical strength of materials approach to pressure vessels. Imagine the pressure vessel shown in Fig. 2 (note, the radius of the…
Angle 1 Tyx Tyx Figure 1 Point A- x-direction stress 60MPA(compression), y-direction stress 40MPA(tension), negative shear stress 30MPA Using your assigned point determine the following for the yz-plane: a) From basic priciples determine the stresses on the plane of the indicated angle 1-30°, Show al calculations. Draw the orientation of the stress block for this scenario. b) Repeat question (a) using a Mohr circle. c) Using a Mohr circle, determine and draw the maximum stress block of the in-plane maximum shear and principle stresses. d) Determine the stresses and orientation of the stress block where the normal stress is zero. Make use of the stress transformation equations. e) Determine the values of absolute maximum shear stress and corresponding normal stress.
A laminae is considered a plate with only biaxial stresses in plane stress conditions. From Generalized Hooke’sLaw that you learnt in Strength of Materials, we know these equations to be true in such conditions. Or in other words, we know the Compliance matrix that represents the laminae. Find the Stiffness matrix of thesame laminae. Or in other words, prove that the equations below are true for the same laminae. The equationsbelow are what we discussed in Lecture. Assume the laminae has isotropic properties.
The state of stress at a point in an engine piston is given in the x-y-z coordinates by: 90 180 [0]=0, MPa = 180 240 yx yy 120 zy Using the matrix transformation law, determine the state of stress at the same point for an element rotated about the x-axis (in the y-z plane) 60° clockwise from its original position. Calculate the stress invariants and write the characteristic equation for the original state of stress, Calculate the deviatoric invariants for the original state of stress, Calculate the principal stresses and the absolute maximum shear stress at the point. What are the stress invariants and the characteristic equation for the transformed state of stress, а. b. С. d. e
The state of stress at a given point is given in the following figure. Use Mohr’s circle to find: a) The principal stresses b) The maximum in-plane shear stresses. For both cases you must draw a rotated element including all stresses and the angle of rotation. You must draw a properly labeled Mohr’s circle.